Telit Wireless Solutions ME910C1-AU Reference guide



ME910C1

AT Commands Reference Guide

80529ST10815A

Rev.2-2017-09-14



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page2of233



APPLICABILITY TABLE

PRODUCT

ME910C1-NA

ME910C1-NV

ME910C1-E1

ME910C1-AU

ME910C1-J1

ME910C1-K1

ME910C1-N1

ME910C1-E2

ME910C1-WW

NE910C1-E1



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page3of233



Contents

1 Introduction ...................................................................................................................................................................... 10

1.1 Scope.....................................................................................................................................10

1.2 Audience................................................................................................................................10

1.3 Contact Information, Support..............................................................................................10

1.4 Document Organization........................................................................................................11

1.5 Text Conventions..................................................................................................................11

1.6 Related Documents...............................................................................................................11

1.7 Document History.................................................................................................................12

2 Overview 13

2.1 About the document..............................................................................................................13

3 AT COMMANDS ............................................................................................................................................................. 14

3.1 Definitions.............................................................................................................................14

3.2 AT Command Syntax............................................................................................................14

 String Type Parameters.......................................................................................................................................15

 Command Lines..................................................................................................................................................15

 ME Error Result Code - +CME ERROR: <err>...................................................................................................18

Message Service Failure Result Code - .............................................................................................. 20

+CMS ERROR: <err> ............................................................................................................................... 20

 Information Responses and Result Codes............................................................................................................21

 Command Response Time-Out............................................................................................................................22

 Command Issuing Timing...................................................................................................................................23

3.3 Storage..................................................................................................................................24

 Factory Profile and User Profiles.........................................................................................................................24

3.4 AT Commands References....................................................................................................26

3.4.1 Command Line General Format....................................................................................................26

3.4.1 Command Line Prefixes .................................................................................................................... 26

 Starting a Command Line - AT ....................................................................................................... 26

 Last Command Automatic Repetition - A/ ...................................................................................... 26

 Hayes Compliant AT Commands........................................................................................................................27

Generic Modem Control .................................................................................................................. 27

 Set To Factory-Defined Configuration - &F ................................................................................... 27

 Soft Reset - Z .................................................................................................................................... 27

 Default Reset Full Profile Designation - &P ................................................................................... 27

 Manufacturer Identification - +GMI ................................................................................................ 28

 Model Identification - +GMM ......................................................................................................... 28

 Revision Identification - +GMR ...................................................................................................... 28

 Serial Number - +GSN ..................................................................................................................... 28

 Display Current Base Configuration and Profile - &V ................................................................... 29

DTE - Modem Interface Control ....................................................................................................... 29



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page4of233



Command Echo - E .......................................................................................................................... 29

 Quiet Result Codes - Q .................................................................................................................... 29

 Response Format - V ........................................................................................................................ 30

 Identification Information - I ........................................................................................................... 31

 Data Carrier Detect (DCD) Control - &C ....................................................................................... 3 1 

 Data Terminal Ready (DTR) Control - &D .................................................................................... 31

 Flow Control - &K ........................................................................................................................... 32

 Fixed DTE Interface Rate - +IPR .................................................................................................... 32

 DTE-Modem Local Flow Control - +IFC ....................................................................................... 33

 DTE-Modem Character Framing - +ICF ......................................................................................... 34

Call Control ................................................................................................................................... 34

 Dial - D ............................................................................................................................................. 34

S Parameters .................................................................................................................................. 37

 Number of Rings to Auto Answer - S0 ........................................................................................... 38

 Command Line Termination Character - S3 ................................................................................... 39

 Response Formatting Character - S4 ............................................................................................... 39

 Command Line Editing Character - S5 ........................................................................................... 39

 3GPP TS 27.007 AT Commands.........................................................................................................................40

General .......................................................................................................................................... 40

 Request Manufacturer Identification - +CGMI ............................................................................... 40

 Request Model Identification - +CGMM ........................................................................................ 40

 Request Revision Identification - +CGMR ..................................................................................... 40



Request Product Serial Number Identification - +CGSN

.................................................................... 40

 Select TE Character Set - +CSCS .................................................................................................... 41

 Request International Mobile Subscriber Identity (IMSI) - +CIMI................................................ 42

 Read ICCID (Integrated Circuit Card Identification) - #CCID ...................................................... 42

 Serial and Software Version Number - +IMEISV .......................................................................... 42

 PCCA STD-101 Select Wireless Network - +WS46 ...................................................................... 43

Network Service Handling ............................................................................................................... 43

 Subscriber Number - +CNUM ......................................................................................................... 43

 Read Operator Names - +COPN ...................................................................................................... 44

 Operator Selection - +COPS ............................................................................................................ 44

 Facility Lock/Unlock - +CLCK ....................................................................................................... 45

 Change Facility Password - +CPWD .............................................................................................. 47

 Preferred Operator List - +CPOL .................................................................................................... 48

 Selection of preferred PLMN list - +CPLS ..................................................................................... 4 9 

Mobile Equipment Control .............................................................................................................. 50

 Set Phone Functionality - +CFUN ................................................................................................... 50

 Enter PIN - +CPIN ........................................................................................................................... 51

 Signal Quality - +CSQ ..................................................................................................................... 53

 Extended Signal Quality - +CESQ ................................................................................................. 54

 Mobile Equipment Event Reporting - +CMER ............................................................................... 56

 Clock Management - +CCLK .......................................................................................................... 57

 Restricted SIM Access - +CRSM .................................................................................................... 58

 Available AT Commands - +CLAC ................................................................................................ 6 0 

Mobile Equipment Errors ................................................................................................................ 60

 Report Mobile Equipment Error - +CMEE ..................................................................................... 60

Commands for GPRS ...................................................................................................................... 62

 GPRS Attach or Detach - +CGATT ................................................................................................ 62

 GPRS Event Reporting - +CGEREP ............................................................................................... 6 2 

 GPRS Network Registration Status - +CGREG .............................................................................. 64

 Printing IP Address Format - +CGPIAF ......................................................................................... 6 6 



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page5of233



Define PDP Context - +CGDCONT ............................................................................................... 67

 Define Secondary PDP Context - +CGDSCONT ........................................................................... 68

 PDP Context Activate Or Deactivate - +CGACT ........................................................................... 69

 PDP Context Modify - +CGCMOD ................................................................................................ 70

 Show PDP Address - +CGPADDR ................................................................................................. 71

 Set mode of operation for EPS - +CEMODE .................................................................................. 71

 3GPP TS 27.005 AT Commands for SMS and CBS............................................................................................73

General Configuration ..................................................................................................................... 73

 Select Message Service - +CSMS ................................................................................................... 73

 Preferred Message Storage - +CPMS .............................................................................................. 74

 Message Format - +CMGF .............................................................................................................. 75

Message Configuration .................................................................................................................... 75

 Service Center Address - +CSCA .................................................................................................... 75

 EPS – Network Registarion Status - +CEREG ............................................................................... 76

 PDP Context Read Dynamic Parameters +CGCONTRDP ............................................................. 78

 Secondary PDP Context Read Dynamic Parameters - +CGSCONTRDP ..................................... 80

 Set Text Mode Parameters - +CSMP .............................................................................................. 81

 Show Text Mode Parameters - +CSDH .......................................................................................... 81

 Save Settings - +CSAS .................................................................................................................... 82

 Restore Settings - +CRES ................................................................................................................ 82

Message Receiving and Reading ...................................................................................................... 83

 New Message Indications to Terminal Equipment - +CNMI ......................................................... 83

 List Messages - +CMGL .................................................................................................................. 87

 Read Message - +CMGR ................................................................................................................. 89

Message Sending and Writing .......................................................................................................... 91

 Send Message - +CMGS .................................................................................................................. 91

 Write Message to Memory - +CMGW ............................................................................................ 94

 Delete Message - +CMGD .............................................................................................................. 97

 PSM and eDRX Commands................................................................................................................................99

PSM AT Commands ....................................................................................................................... 99

 Power Saving Mode Setting - +CPSMS .......................................................................................... 99

eDRX AT Commands ................................................................................................................... 101

 eDRX setting - +CEDRXS ............................................................................................................ 101

 eDRX read dynamic parameters - +CEDRXRDP ......................................................................... 103

 Custom AT Commands.....................................................................................................................................104

Configuration AT Commands ........................................................................................................ 104

 Manufacturer Identification - #CGMI ........................................................................................... 104

 Model Identification - #CGMM .................................................................................................... 104

 Revision Identification - #CGMR ................................................................................................. 104

 Product Serial Number Identification - #CGSN ............................................................................ 105

 International Mobile Subscriber Identity (IMSI) - #CIMI ............................................................ 106

 Display PIN Counter - #PCT ......................................................................................................... 106

 Software ShutDown - #SHDN ....................................................................................................... 107

 Rebbots the unit - #REBOOT ........................................................................................................ 107

 Periodic Reset - #ENHRST ........................................................................................................... 107

 General Purpose Input/Output Pin Control - #GPIO .................................................................... 108

 Read Analog/Digital Converter Input - #ADC .............................................................................. 111

 Battery and Charger Status - #CBC ............................................................................................... 112

 V24 Output Pins Configuration - #V24CFG ................................................................................. 112

 V24 Output Pins Control - #V24 ................................................................................................... 113

 Cell Monitor - #MONI ................................................................................................................... 113

 Packet Service Network Type - #PSNT ........................................................................................ 116



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page6of233



Read Current Network Status in 3G Network - #RFSTS ............................................................. 118

 Temperature Monitor- #TEMPMON ............................................................................................ 122

 Temperature Monitor CONFIGURATION - #TEMPCFG........................................................... 123

 Wake from Alarm Mode - #WAKE .............................................................................................. 127

 AlARM PIN - #ALARMPIN ......................................................................................................... 127

 Serving Cell Information - #SERVINFO ...................................................................................... 128

 Query SIM Status - #QSS .............................................................................................................. 129

 Network Timezone - #NITZ .......................................................................................................... 130

 Clock Mode - #CCLKMODE ........................................................................................................ 131

 Calculate and update date and time - #NTP .................................................................................. 133

 Alarm Management - +CALA ....................................................................................................... 134

 Delete Alarm - +CALD ................................................................................................................. 136

 Generic SIM access - +CSIM ........................................................................................................ 136

 Select Band - #BND ....................................................................................................................... 139

 Skip Escape Sequence - #SKIPESC .............................................................................................. 1 4 1 

 PPP-GPRS Connection Authentication Type - #GAUTH ............................................................ 141

 SIM Detection Mode-#SIMDET ................................................................................................... 1 4 2 

 Write to I2C - #I2CWR .................................................................................................................. 142

 Read to I2C - #I2CRD ................................................................................................................... 143

 Enable Test Mode command in not signalling mode - #TESTMODE ......................................... 144

 Update PLMN List - #PLMNUPDATE ........................................................................................ 146

 Select IoT technology - #WS46 ..................................................................................................... 147

 Set Active Firmware Image - #FWSWITCH ................................................................................ 147

Multisocket AT Commands ........................................................................................................... 148

 Socket Status - #SS ........................................................................................................................ 148

 Socket Info - #SI ............................................................................................................................ 148

 Socket Type - #ST .......................................................................................................................... 150

 Context Activation - #SGACT ...................................................................................................... 150

 Socket Shutdown - #SH ................................................................................................................. 152

 Socket Configuration - #SCFG ...................................................................................................... 152

 Context activation configuration extended - #SGACTCFGEXT ................................................. 153

 PAD forward character - #PADFWD ............................................................................................ 154

 PAD command features - #PADCMD .......................................................................................... 155

 Socket Configuration Extended - #SCFGEXT ............................................................................. 155

 Socket Configuration Extended 2 - #SCFGEXT2 ........................................................................ 157

 Socket Configuration Extended 3 - #SCFGEXT3 ........................................................................ 159

 Socket Dial - #SD ........................................................................................................................... 160

 Socket Accept - #SA ...................................................................................................................... 161

 Socket Restore - #SO ..................................................................................................................... 162

 Socket Listen - #SL ........................................................................................................................ 162

 Detect the Cause of a Socket disconnection - #SLASTCLOSURE ............................................. 163

 Socket Listen UDP - #SLUDP ....................................................................................................... 164

 Receive Data in Command Mode - #SRECV ............................................................................... 165

 Send UDP data to a specific remote host - #SSENDUDP ............................................................ 167

 Send UDP data to a specific remote host extended - #SSENDUDPEXT .................................... 168

 Send Data in Command Mode - #SSEND .................................................................................... 168

 Send data in Command Mode extended - #SSENDEXT .............................................................. 169

 Context Activation and Configuration - #SGACTCFG ................................................................ 171

SSL Commands ............................................................................................................................ 172

 Enable a SSL socket - #SSLEN ..................................................................................................... 172

 Opens a socket SSL to a remote server - #SSLD .......................................................................... 173

 Send data through a SSL socket - #SSLSEND ............................................................................. 174



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page7of233



Read data from a SSL socket - #SSLRECV .................................................................................. 176

 Report the status of a SSL socket - #SSLS .................................................................................... 1 7 7 

 Close a SSL socket - #SSLH ......................................................................................................... 177

 Restore a SSL socket after a +++ - #SSLO ................................................................................... 178

 Configure general parameters of a SSL socket - #SSLCFG ......................................................... 179

 Configure security parameters of a SSL socket – #SSLSECCFG ................................................ 179

 Manage the security data - #SSLSECDATA ................................................................................ 180

FTP AT Commands ...................................................................................................................... 182

 FTP Time – Out - #FTPTO ............................................................................................................ 182

 FTP Open - #FTPOPEN ................................................................................................................ 182

 FTP Close - # FTPCLOSE ............................................................................................................. 183

 FTP Config - #FTPCFG ................................................................................................................. 183

 FTP Put - #FTPPUT ....................................................................................................................... 184

 FTP Get - #FTPGET ...................................................................................................................... 184

 FTP Get in command mode - #FTPGETPKT ............................................................................... 185

 FTP Type - #FTPTYPE ................................................................................................................. 185

 FTP Delete - #FTPDELE ............................................................................................................... 186

 FTP Print Working Directory - #FTPPWD ................................................................................... 186

 FTP Change Working Directory - #FTPCWD .............................................................................. 186

 FTP List - #FTPLIST ..................................................................................................................... 187

 Get file size from FTP - #FTPFSIZE ............................................................................................. 187

 FTP Append - #FTPAPP................................................................................................................ 187

 Set restart position for FTP GET - #FTPREST ............................................................................. 188

 Receive Data In Command Mode - #FTPRECV ........................................................................... 189

 FTP Append Extended - #FTPAPPEXT ....................................................................................... 190

 FTP Read Message - #FTPMSG.................................................................................................... 1 9 2 

AT Commands ............................................................................................................................. 192

 Query DNS - #QDNS .................................................................................................................... 192

 DNS Response Caching - #CACHEDNS ...................................................................................... 193

 Manual DNS Selection - #DNS ..................................................................................................... 193

 Socket Listen Ring - #E2SLRI ...................................................................................................... 194

 Firewall Setup - #FRWL ................................................................................................................ 195

 GPRS Data Volume - #GDATAVOL ........................................................................................... 196

 DNS from Network - #NWDNS .................................................................................................... 1 9 7 

Easy Scan® Extension AT Commands ............................................................................................ 198

 Network survey - #CSURV ........................................................................................................... 198

 Network Survey (Numeric Format) - #CSURVC ......................................................................... 202

 Network Survey Format - #CSURVF ........................................................................................... 205

 <CR><LF> Removing On Easy Scan® Commands Family -#CSURVNLF .............................. 206

 Extended network survey - #CSURVEXT .................................................................................... 206

HTTP AT COMMANDS ............................................................................................................... 207

 Configure HTTP parameters - #HTTPCFG .................................................................................. 207

 Send HTTP GET, HEAD or DELETE request - #HTTPQRY ..................................................... 208

 Send HTTP POST or PUT request - #HTTPSND ........................................................................ 210

 Receive HTTP server data - #HTTPRCV ..................................................................................... 212

GPS AT Commands Set ................................................................................................................ 213

 GPS Power Management - $GPSP ................................................................................................ 213

 GPS Module Reset - $GPSR ......................................................................................................... 213

 Get Acquired Position - $GPSACP ............................................................................................... 214

 Unsolicited NMEA Data Configuration - $GPSNMUN ............................................................... 216

 Save GPS Parameters Configuration - $GPSSAV ........................................................................ 217

 Restore to Default GPS Parameters - $GPSRST ........................................................................... 217



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page8of233



GPS Antenna Supply Voltage Readout - $GPSAV ...................................................................... 218

 GPS Antenna Type Definition - $GPSAT ..................................................................................... 218

 Set the GNSS (or GLONASS) Capability - $GPSGLO ................................................................ 218

 Unsolicited NMEA Extended Data Configuration - $GPSNMUNEX ......................................... 219

 GPS Quality of Service - $GPSQOS ............................................................................................. 2 2 0 

 GPS Start Location Service Request-$GPSSLSR ......................................................................... 221

 GPS Stop Location Service Request - $GPSSTOP ....................................................................... 224

 Update SLP address - $SLP ........................................................................................................... 224

 Update SLP address - $LCSSLP ................................................................................................... 225

 Update SLP address type - $SLPTYPE ......................................................................................... 225

 Set the User Plane Secure Transport - $SUPLSEC ....................................................................... 226

 Configure SUPL TLS and Hash - $SUPLCFG ............................................................................. 226

 Set the version of supported SUPL - $SUPLV ............................................................................. 227

 Update location information - $LCSLUI ....................................................................................... 227

 Update terminal information - $LCSTER ..................................................................................... 227

 Enable/Disable unsolicited response - $LICLS ............................................................................. 228

 LCS certificate - $LTC .................................................................................................................. 229

 Lock context for LCS use - $LCSLK ............................................................................................ 2 2 9 

 Clear GPS Data - $GPSCLRX ....................................................................................................... 230

3.5 AT parser abort...................................................................................................................231

4 List of acronyms ............................................................................................................................................................. 232



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page9of233



DISCLAIMER

The information contained in this document is the proprietary information of Telit Communications S.p.A. and its

affiliates (“TELIT”).

The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors

of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited.

Telit makes every effort to ensure the quality of the information it makes available. Notwithstanding the foregoing, Telit

does not make any warranty as to the information contained herein, and does not accept any liability for any injury, loss

or damage of any kind incurred by use of or reliance upon the information.

Telit disclaims any and all responsibility for the application of the devices characterized in this document, and notes that

the application of the device must comply with the safety standards of the applicable country, and where applicable,

with the relevant wiring rules.

Telit reserves the right to make modifications, additions and deletions to this document due to typographical errors,

inaccurate information, or improvements to programs and/or equipment at any time and without notice.

Such changes will, nevertheless be incorporated into new editions of this document.

Copyright: Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents

and communication thereof to others without express authorization are prohibited. Offenders will be held liable for

payment of damages. All rights are reserved.



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page10of233



1 Introduction

1.1 Scope

This document is aimed at providing a detailed specification and a comprehensive listing as a Reference for the whole

set of AT command

1.2 Audience

Readers of this document should be familiar with Telit modules and their ease of controlling by means of AT Commands.

1.3 Contact Information, Support

For general contact, technical support, to report documentation errors and to order manuals, contact Telit’s Technical

Support Center (TTSC) at:

[email protected]

TS-NORTHAMER[email protected]

[email protected]

Alternatively, use:

http://www.telit.com/en/products/technical-support-center/contact.php

For detailed information about where you can buy the Telit modules or for recommendations on accessories and

components visit:

http://www.telit.com

To register for product news and announcements or for product questions contact Telit’s Technical Support Center

(TTSC).

Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for

improvements.

Telit appreciates feedback from the users of our information.



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page11of233



1.4 Document Organization

This document contains the following chapters:

Chapter 1: “Introduction” provides a scope for this document, target audience, contact and support

information, and text conventions.

Chapter 2: “Overview” about the aim of this document and implementation suggestions.

Chapter 3: “AT Commands” The core of this Reference guide.

1.5 Text Conventions

Danger – This information MUST be followed or catastrophic equipment failure or bodily injury may occur.

Caution or Warning – Alerts the user to important points about integrating the module, if these points are not followed,

the module and end user equipment may fail or malfunction.

Tip or Information – Provides advice and suggestions that may be useful when integrating the module.

All dates are in ISO 8601 format, i.e. YYYY-MM-DD.

1.6 Related Documents

 ETSI GSM 07.07 specification and rules

http://www.3gpp.org/ftp/Specs/archive/07_series/07.07/

 ETSI GSM 07.05 specification and rules

http://www.3gpp.org/ftp/Specs/archive/07_series/07.05/

 Hayes standard AT command set



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page12of233



1.7

Document History

Revision Date SW release Changes

ISSUE #0 2017-03-10

30.00.xx0-Bxxx

First release

ISSUE #1 2017-08-14 30.00.xx1-Bxxx Updated applicability table

ISSUE #2 2017-09-14

30.00.xx1-Bxxx

30.00.xx2

Updated applicability table

Updated Commands and Aligned to first Mass Production

Release 30.00.xx2



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page13of233



2 Overview

2.1 About the document

This document is to describe all AT commands implemented on the Telit wireless modules listed on the

applicability table.



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page14of233



3 AT COMMANDS

The Telit wireless modules family can be controlled via the serial interface using the standard AT commands

1

.

The Telit wireless modules family is compliant with:

1. Hayes standard AT command set, in order to maintain the compatibility with existing SW programs.

2. ETSI GSM 07.07 specific AT command and GPRS specific commands.

3. ETSI GSM 07.05 specific AT commands for SMS (Short Message Service) and CBS (Cell Broadcast Service)

4. FAX Class 1 compatible commands

Moreover Telit wireless modules family supports also Telit proprietary AT commands for special purposes.

The following is a description of how to use the AT commands with the Telit wireless module family.

3.1 Definitions

The following syntactical definitions apply:

<CR> Carriage return character, is the command line and result code terminator character, which value, in

decimal ASCII between 0 and 255,is specified within parameter

S3. The default value is 13.

<LF> Linefeed character, is the character recognised as line feed character. Its value, in decimal ASCII between

0 and 255, is specified within parameter

S4. The default value is 10. The line feed character is output after

carriage return character if verbose result codes are used (

V1 option used). Otherwise, if numeric format result

codes are used (

V0 option used) it will not appear in the result codes.

<...> Name enclosed in angle brackets is a syntactical element. It does not appear in the command line.

[...] Optional subparameter of a command or an optional part of TA information response is enclosed in square

brackets. Brackets themselves do not appear in the command line. When subparameter is not given in AT

commands which have a Read command, new value equals to its previous value. In AT commands which do

not store the values of any of their subparameters (called action type commands), and so don’t have a Read

command, action should be done on the basis of the recommended default setting of the subparameter.

3.2 AT Command Syntax

The syntax rules followed by Telit implementation of either Hayes AT commands or GSM/WCDMA

commands are very similar to those of standard basic and extended AT commands. There are two types of

extended command:



1

The AT is an ATTENTION command and is used as a prefix to other parameters in a string. The AT command

combined with other parameters can be set up in the communications package or typed in manually as a

command line instruction.



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page15of233



- Parameter type commands. This type of commands may be “set” (to store a value or values for later use),

“read” (to determine the current value or values stored), or “tested” (to determine ranges of values

supported). Each of them has a test command (trailing ‘=?’) to give information about the type of its

subparameters; they also have a Read command (trailing ‘?’) to check the current values of subparameters.

- Action type commands. This type of command may be “executed” or “tested”:

 “executed“ to invoke a particular function of the equipment, which generally involves more than the

simple storage of a value for later use

 “tested” to determine whether or not the equipment implements the Action Command (in this case

issuing the correspondent Test command - trailing =? - returns the OK result code), and if

subparameters are associated with the action, the ranges of subparameters values that are supported.

Action commands do not store the values of any of their possible subparameters.

Moreover:

o The response to the Test Command (trailing =?) may be changed in the future by Telit to allow

the description of new values/functionalities

o If all the subparameters of a parameter type command +CMD (or #CMD or $CMD) are

optional, issuing AT+CMD=<CR> (or AT#CMD=<CR> or AT$CMD=<CR>) causes the OK

result code to be returned and the previous values of the omitted subparameters to be retained.

String Type Parameters

A string must be enclosed between quotes or it will not be considered as a valid string type parameter input.

According to V25.ter, space characters are ignored on the command line and may be used freely for

formatting purposes, unless they are embedded on numeric or quoted string constants. Therefore a string

containing a space character has to be enclosed between quotes to be considered a valid string type

parameter (e.g. typing AT+COPS=1,0,”A1” is the same as typing AT+COPS=1,0,A1; typing

AT+COPS=1,0,”A BB” is different from typing AT+COPS=1,0,A BB).

A small set of commands always requires writing the input string parameters within quotes. This is

explicitly reported in the specific descriptions.

Command Lines

A command line is made up of three elements: the prefix, the body and the termination character.

The command line prefix consists of the characters “AT” or “at”, or, to repeat the execution of the previous

command line, the characters “A/” or “a/”.



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page16of233



The termination character may be selected by a user option (parameter S3), the default being <CR>.

The basic structures of the command line are:



ATCMD1<CR> where AT is the command line prefix, CMD1 is the body of a basic command

(nb: the name of the command never begins with the character “

+”) and <CR> is the command line

terminator character



ATCMD2=10<CR> where 10 is a subparameter



AT+CMD1 ;+CMD2=, ,10<CR> These are two examples of extended commands (nb: the name

of the command always begins with the character “

+”

2

).

They are delimit with semicolon. In the second command, the subparameter omitted.



+CMD1?<CR> This is a Read command for checking current subparameter values



+CMD1=?<CR> This is a test command for checking possible subparameter values

These commands might be performed in a single command line as shown below:

ATCMD1 CMD2=10+CMD1;+CMD2=, ,10;+CMD1?;+CMD1=?<CR>

Anyway it is always preferable to separate into different command lines the basic commands and the extended

commands.

Furthermore it is suggested to avoid placing several action commands in the same command line, because if

one of them fails, then an error message is received but it is not possible to argue which one of them has failed

the execution.

If command

V1 is enabled (verbose responses codes) and all commands in a command line have been

performed successfully, result code

<CR><LF>OK<CR><LF> is sent from the TA to the TE.

If subparameter values of a command are not accepted by the TA or command itself is invalid, or command

cannot be performed for some reason, result code

<CR><LF>ERROR<CR><LF> is sent and no

subsequent commands in the command line are processed.

If command

V0 is enabled (numeric responses codes) and all commands in a command line have been

performed successfully, result code

0<CR> is sent from the TA to the TE.

If sub-parameter values of a command are not accepted by the TA or command itself is invalid, or command

cannot be performed for some reason, result code

4<CR> and no subsequent commands in the command line

are processed.



2

ThesetofproprietaryATcommandsdifferentiatesfromthestandardonebecausethenameofeachofthem

beginswitheither“@”,“#”,“$”or“*”.ProprietaryATcommandsfollowthesamesyntaxrulesasextended

commands



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page17of233



In case of errors depending on ME operation, ERROR (or 4) response may be replaced by +CME ERROR:

<err> or +CMS ERROR: <err>

.

NOTE: The command line buffer accepts a maximum of 80 characters. If this number is

exceeded none of the commands will be executed and TA returns ERROR.



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page18of233



ME Error Result Code - +CME ERROR: <err>

This is NOT a command it is the error response to +Cxxx 3gpp

TS 27.007 commands.

Syntax: +CME ERROR: <err>

Parameter: <err> - error code can be either numeric or verbose (see +CMEE).The possible values

of <err> are reported in the below table:

Numeric Format Verbose Format

General errors:

0

p

hone failure

1

N

o connection to

p

hone

2

p

hone-ada

p

tor link reserve

d

3 o

p

eration not allowed

4 o

p

eration not su

pp

orted

5 PH-SIM PIN re

q

uired

10 SIM not inserted

11 SIM PIN re

q

uired

12 SIM PUK re

q

uired

13 SIM failure

14 SIM bus

y

15 SIM wron

g

16 incorrect

p

assword

17 SIM PIN2 re

q

uired

18 SIM PUK2 re

q

uired

20 memor

y

full

21 invalid index

22 not found

23 memor

y

failure

24 text strin

g

too lon

g

25 invalid characters in text strin

g

26 dial strin

g

too lon

g

27 invalid characters in dial strin

g

30 no network service

31 network time-out

32 network not allowed - emer

g

enc

y

calls onl

y

40 network

p

ersonalization PIN re

q

uired

41 network

p

ersonalization PUK re

q

uired

42 network subset

p

ersonalization PIN re

q

uired

43 network subset

p

ersonalization PUK re

q

uired

44 service

p

rovider

p

ersonalization PIN re

q

uired

45 Service

p

rovider

p

ersonalization PUK re

q

uired

46 cor

p

orate

p

ersonalization PIN re

q

uired

47 cor

p

orate

p

ersonalization PUK re

q

uired

General

p

ur

p

ose error:

100 unknown

770 SIM invalid

GPRS related errors to a failure to

p

erform an Attach:

103 Ille

g

al MS

(

#3

)

*



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page19of233



Numeric Format Verbose Format

106 Ille

g

al ME

(

#6

)

*

107 GPRS service not allowed

(

#7

)

*

111 PLMN not allowed

(

#11

)

*

112 Location area not allowed

(

#12

)

*

113 Roamin

g

not allowed in this location area

(

#13

)

*

GPRS related errors to a failure to Activate a Context and others:

132 service o

p

tion not su

pp

orted

(

#32

)

*

133 re

q

uested service o

p

tion not subscribed

(

#33

)

*

134 service o

p

tion tem

p

oraril

y

out of order

(

#34

)

*

148 uns

p

ecified GPRS erro

r

149 PDP authentication failure

150 invalid mobile class

Eas

y

GPRS® related errors

550

g

eneric undocumented erro

r

551 wron

g

state

552 wron

g

mode

553 context alread

y

activated

554 stack alread

y

active

555 activation failed

556 context not o

p

ened

557 cannot setu

p

socket

558 cannot resolve DN

559 time-out in o

p

enin

g

socket

560 cannot o

p

en socket

561 remote disconnected or time-out

562 connection faile

d

563 tx erro

r

564 alread

y

listenin

g

Network surve

y

errors

657

N

etwork surve

y

error

(

No Carrier

)

*

658

N

etwork surve

y

error

(

Bus

y)

*

659

N

etwork surve

y

error

(

Wron

g

re

q

uest

)

*

660

N

etwork surve

y

error

(

Aborted

)

*

Su

pp

lementar

y

service related error

257 network re

j

ected re

q

uest

258 retr

y

o

p

eration

259 invalid deflected to numbe

r

260 deflected to own numbe

r

261 unknown subscribe

r

262 service not available

263 unknown class s

p

ecifie

d

264 unknown network messa

g

e

AT+COPS test command related error

680 LU

p

rocessin

g

681

N

etwork search aborte

d

682 PTM mode

AT+WS46 test command related error

683 Active call state

684 RR connection Established



AT Commands Reference Guide

80529ST10815A Rev.2– 2017-09-14



ReproductionforbiddenwithoutTelitCommunicationsS.p.A.writtenauthorization‐AllRightsReserved  page20of233



*(Values in parentheses are 3gpp TS 24.008 cause codes) Message Service Failure Result Code - +CMS ERROR:

<err>

Message Service Failure Result Code -

+CMS ERROR: <err>

This is NOT a command; it is the error response to +Cxxx

3gpp TS 27.005 commands.

Syntax: +CMS ERROR: <err>

Parameter: <err> - numeric error code. The <err> values are reported in the below table:

Numeric Format Meaning

0...127 3gpp TS 24.011 Annex E-2 values

128...255 3gpp TS 23.040 sub clause 9.2.3.22 values

300 ME failure

301 SMS service of ME reserved

302 operation not allowed

303 operation not supported

304 invalid PDU mode parameter

305 invalid text mode parameter

310 SIM not inserted

311 SIM PIN required

312 PH-SIM PIN required

313 SIM failure

314 SIM busy

315 SIM wrong

316 SIM PUK required

317 SIM PIN2 required

318 SIM PUK2 required

320 memory failure

321 invalid memory index

322 memory full

330 SMSC address unknown

331 no network service

332 network time-out

340 no +CNMA acknowledgement expected

500 unknown error

Page is loading ...

Telit Wireless Solutions ME910C1-AU Reference guide

This manual is also suitable for

Telit Wireless Solutions ME910C1-AU Reference guide

Related papers

Other documents