ANTLUX AntLux 4FT LED Wraparound Light Flush Mount LED Shop Lights, 50W 5600 Lumens, 4000K Neutral White, 4 Foot Integrated Wrap Linear Puff Office Ceiling Lighting, Fluorescent Tube Replacement, 8 Pack User manual

Brand
ANTLUX
Model
AntLux 4FT LED Wraparound Light Flush Mount LED Shop Lights, 50W 5600 Lumens, 4000K Neutral White, 4 Foot Integrated Wrap Linear Puff Office Ceiling Lighting, Fluorescent Tube Replacement, 8 Pack
Category
Motorcycle Accessories
Type
User manual
INSTRUCTION MANUAL
Wraparound
SAFETY INFORMATION
IMPORTANT: Read all safety precautions and installation instructions carefully before installing
◆Do not install the fixture with power on, also do not operate by wet hands.
◆Ensure that the fixture is mounted onto a good structurally surface that will support the fixture.
◆The fixture is designed for using 120VAC. 60Hz.
◆Product can be used in shops, supermarkets, Hospitals, airports, office buildings, government buildings,
subway etc.
◆Do not install on radiant-heating type ceiling.
WARNING: IF NOT FOLLOW THE INSTRUCTION MAY LEAD TO A POTENTIALLY FATAL
ELECTRICAL SHOCK OR PROPERTY DAMAGE
PRE-INSTALLATION
HARDWARE INCLUDED
INSTALLATION
CAUTION: Before beginning installation turn off the circuit breaker and light switch
Junction box is required for assembly
1. Remove diffuser (Part C) from housing (Part A) side by side carefully.
AA: Screws (2pcs)
BB: Wire Nut (3pcs)
CC: Screws (4pcs)
DD: Wall Anchors (4pcs)
Figure 1
EE: Expansion screws (2pcs)
INSTALLATION(CONTINUED)
CONNECTING THE WIRES
1. Install the two screws(AA) into the junction box.(Figure2)
2.Wiring connection by using the wire nut (BB). Ground wire connects the yellow/green ground wire of the light.
White wire connects the white wire of the light, and black wire connects the black wire of the light.
NOTE: For proper connection, place the wire nuts (BB) over wires and twist clockwise until tight (Figure 3).
OPTIONAL: Wrap connected wire nuts with electrical tape.
INSTALLATION(CONTINUED)
ATTACHING THE HOUSING
1.Attach the housing to the junction box by aligning the hoes on the Housing (Part A) with the screws on the junction box.
2.Turn housing clockwise to lock in right place and tighten screws to ensure the fixture is secure and stable .(Figure4)
3.InstallationⅠ:Put the screws (CC) through the housing (Part A), attaching it in the ceiling. Fasten all the four screws (CC)
with screwdriver. （Figure 5）
InstallationⅡ:Put the screws (EE) through the housing (Part A), attaching into the bolts (EE) in the ceiling. Fasten all the
four screws (EE) with screwdriver. （Figure 5）
ATTACHING THE DIFFUSER
4.Install diffuser (Part C) starting at one side of housing, insert diffuser slot onto edge of housing (see Fig1) carefully, and
squeeze diffuser to engage opposite side of the housing. Continue this action down length of diffuser until fully installed
onto housing. (Figure6)
Figure 3
Figure 4
Figure 6
Figure 2
Figure 5
Figure 3
  • Page 1 1
  • Page 2 2

ANTLUX AntLux 4FT LED Wraparound Light Flush Mount LED Shop Lights, 50W 5600 Lumens, 4000K Neutral White, 4 Foot Integrated Wrap Linear Puff Office Ceiling Lighting, Fluorescent Tube Replacement, 8 Pack User manual

Brand
ANTLUX
Model
AntLux 4FT LED Wraparound Light Flush Mount LED Shop Lights, 50W 5600 Lumens, 4000K Neutral White, 4 Foot Integrated Wrap Linear Puff Office Ceiling Lighting, Fluorescent Tube Replacement, 8 Pack
Category
Motorcycle Accessories
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents