Broadcom HFBR-0541Z Evaluation Kit User guide

Type
User guide
HFBR-0541Z Evaluation Kit
DC to 16MBd Sercos 650nm Fiber Optics Eval Kit
User Guide
Introduction
HFBR-0541Z evaluation kit is used to evaluate Avago ber optic device HFBR-1506AMZ and HFBR-2506AMZ. The evalu-
ation kit is equipped with necessary documents and accessories to ease product evaluation and verication.
Evaluation Kit
HFBR-0541Z contains:
1. Evaluation board
2. HFBR-1506AMZ and HFBR-2506AMZ unit
3. HCS Cable with SMA connector
4. HFBR-1506AMZ /2506AMZ datasheet
5. User guide document
Evaluation Board
The basic evaluation board that you receive from Avago incorporates transmitter driver IC SN75451BD, some passive
components, and SMA connectors for the TX input (TXD) and RX output (RXD) port connection. This basic evaluation
board allows you to connect waveform/pattern generator to the TXD with TTL input signal. Receivers output signal can
be monitored from the RXD or RXout with oscilloscope by using high impedance setting.
Initial Setup
1. Connect 5V supply voltage to TXVCC and RXVCC
2. Connect 0V to TXGND and RXGND
3. Connect TXD to pattern generator output
4. Connect RXout to Oscilloscope with high impedance probe
Bit Error Rate Test Setup
Though the transmitter driver IC’s input and receivers output is based on TTL logic (high impedance), the board can be
modied to connect 50ohm load instrument by doing the following steps:
1. Put R2 (50 ohm resistor).
2. Remove R3 (0 ohm resistor).
3. Put R4 (0 ohm resistor) and R7 (50 ohm resistor).
4. Put U3 (SN74LVC2G125).
5. Connect BVCC (5V) and BGND (0V).
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2010 Avago Technologies. All rights reserved.
AV02-2721EN - November 4, 2010
5
6
7
8
1 4
TX
HFBR-1 506AMZ
5
6
7
8
1 4
RX
HFBR-2 506AMZ
TXVCC
RXVCC
TXGND
RXGND
TXGND
RXGND
TXGND
TXGND
RXGND
RXGND
100nF
C3
Cap Semi
TXGND
RXGND
2
2
1
1
Jack
TXVCC
Test_Jack
2
2
1
1
Jack
TXGND
Test_Jack
2
2
1
1
Jack
RXVCC
Test_Jack
2
2
1
1
Jack
RXGND
Test_Jack
TXGND TXGND
TXVCC TXVCC
RXVCC RXVCC
RXGND RXGND
47
R1
Res Semi
1OEb
1
1A
2
2Y
3
GND
4
2A
5
1Y
6
2OEb
7
VCC
8
U3
SN74 LVC2G12 5
0
R3
Res Semi
50
R7
Res Semi
0
R4
Res Semi
BGND
BGND
BVCC
2
2
1
1
Jack
BVCC
Test_Jack
2
2
1
1
Jack
BGND
Test_Jack
BVCC BVCC
BGND BGND
BGND
50
R5
Res Semi
Pin
1
GND
2
TXin
Pin
Pin
1
GN D
2
RXo ut
Pin
TXGND
RXGND
0.1uF
C2
1
1
2
3
4
5
TXD
SMA
1
1
2
3
4
5
RXD
SMA
0
R6
Res Semi
1A
1
2A
6
1B
2
2B
7
VCC
8
GND
4
1Y
3
2Y
5
U1
SN75 451BD
50
R2
Res Semi
TXVCC
TXGND
10uF
C1
T491B106K0 16AT
2.7
R8
Res Semi
  • Page 1 1
  • Page 2 2

Broadcom HFBR-0541Z Evaluation Kit User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI