Advantech Computer Hardware PCI-1710 User manual

PCI-1710/1710HG

Multifunction DAS Card for

PCI Bus

User's manual

Copyright

This documentation and the software included with this product are

copyrighted 1998 by Advantech Co., Ltd. All rights are reserved.

Advantech Co., Ltd. reserves the right to make improvements in the

products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written

permission of Advantech Co., Ltd. Information provided in this manual

is intended to be accurate and reliable. However, Advantech Co., Ltd.

assumes no responsibility for its use, nor for any infringements of the

rights of third parties which may result from its use.

Acknowledgments

PC-LabCard is a trademark of Advantech Co., Ltd. IBM and PC are

trademarks of International Business Machines Corporation. MS-DOS

and Windows are trademarks of Microsoft Corporation. Intel and

Pentium are trademarks of Intel Corporation.

CE notification

The PCI-1710/1710HG, developed by ADVANTECH CO., LTD., has

passed the CE test for environmental specifications when shielded

cables are used for external wiring. We recommend the use of shielded

cables. This kind of cable is available from Advantech. Please contact

your local supplier for ordering information.

On-line Technical Support

For technical support and service please visit our support website at

http:/support.advantech.com

Part No. 2003171010 2nd Edition

Printed in Taiwan Feburary 1999

Contents

Chapter 1: General Information ............................. 1

1.1 Introduction ............................................................... 2

1.2 Features .................................................................... 3

1.3 Specifications............................................................. 4

1.4 Block Diagram........................................................... 8

Chapter 2: Installation.............................................. 9

2.1 Initial Inspection ....................................................... 10

2.2 Unpacking ............................................................... 10

2.3 Installation Instructions ............................................. 11

Chapter 3: Signal Connections.............................. 13

3.1 Overview................................................................. 15

3.2 I/O Connector ......................................................... 15

3.3 Analog Input Connections ........................................ 19

3.4 Analog Output Connections ..................................... 23

3.5 Trigger Source Connections ..................................... 25

3.6 Field Wiring Considerations...................................... 25

Chapter 4: Register Structure and Format ......... 27

4.1 Overview................................................................. 28

4.2 I/O Port Address Map............................................. 28

4.3 Channel Number and A/D Data ............................... 33

4.4 Software A/D Trigger............................................... 33

4.5 A/D Channel Range Setting ...................................... 34

4.6 MUX Control .......................................................... 37

4.7 Control Register....................................................... 39

4.8 Status Register ......................................................... 40

4.9 Clear Interrupt and FIFO ......................................... 41

4.10 D/A Channel 0 Output ............................................. 42

4.11 D/A Channel 1 Output ............................................. 42

4.12 D/A Reference Control ............................................ 43

4.13 Digital I/O Registers................................................. 44

4.14 Programmable Timer/Counter Registers .................... 44

Chapter 5: Calibration............................................ 45

5.1 Introduction ............................................................. 46

5.2 VR Assignment ........................................................ 46

5.3 A/D Calibration ....................................................... 47

5.4 D/A Calibration ....................................................... 48

5.5 Self A/D Calibration................................................. 49

Appendix A: 82C54 Counter Chip Functions ......51

A.1 The Intel 82C54 ...................................................... 52

A.2 Counter Read/Write and Control Registers ............... 53

A.3 Counter Operating Modes ....................................... 56

A.4 Counter Operations ................................................. 58

Chapter 1 General Information 1

1

General Information

CHAPTER

2 PCI-1710 /1710HG User's Manual

1.1 Introduction

The PCI-1710/1710HG is a multifunction DAS card for the PCI bus.

Advanced circuit design brings you higher quality and more func-

tions, including the five most desired measurement and control

functions: 12-bit A/D conversion, D/A conversion, digital input,

digital output, and counter/timer.

PCI-bus Plug and Play

The PCI-1710/1710HG uses a PCI controller to interface the card with

the PCI bus. The controller fully implements the PCI bus specifica-

tion Rev 2.1. All bus relative configurations, such as base address

and interrupt assignment, are automatically controlled by software.

No jumper or DIP switch setting is required for user configuration.

Flexible Inputs Types and Ranges Setting

The PCI-1710/1710HG features an automatic channel/gain scanning

circuit. The circuit, rather than your software, controls multiplexer

switching during sampling. The on-board SRAM stores different gain

values and configuration for each channel. This design lets you

perform multi-channel high-speed sampling (up to 100 kHz) with

different gains for each channel with free combination of single-ended

and differential inputs.

On-board FIFO (First In First Out) Memory

The PCI-1710/1710HG has an on-board FIFO buffer which can store

up to 4K A/D samples. The PCI-1710/1710HG generates an interrupt

when the FIFO is half full. This feature provides continuous high-

speed data transfer and more predictable performance on Windows

systems.

Chapter 1 General Information 3

On-board Programmable Counter

The PCI-1710/1710HG provides a programmable counter for generat-

ing a pacer trigger for the A/D conversion. The counter chip is an

82C54 or equivalent, which includes three 16-bit counters on a 10

MHz clock. One counter is used as an event counter for counting

events coming from the input channels. The other two are cascaded

together to make a 32-bit timer for a pacer trigger.

1.2 Features

• 16 single-ended or 8 differential analog inputs, or a combination

• 12-bit A/D converter, with up to 100 kHz sampling rate

• Programmable gain for each input channel

• Automatic channel/gain scanning

• On-board 4K samples FIFO buffer

• Two 12-bit analog output channels

• 16 digital inputs and 16 digital outputs

• Programmable pacer/counter

4 PCI-1710 /1710HG User's Manual

1.3 Specifications

Analog Input:

• Channels: 16 single-ended or 8 differential (software programma-

ble)

• Resolution: 12-bit

• On-board FIFO: 4K samples

• Conversion time: 8 µs

• Input range: (V, software programmable)

• Maximum Input Overvoltage: ±30 V

• Common Mode Rejection Ratio (CMRR)

PCI-1710 PCI-1710HG

Bipolar

±10, ±5, ±2.5, ±1.25,

±0.625

±10, ±5, ±1, ±0.5, ±0.1, ±0.05,

±0.01, ±0.005

Unipolar

0 ~ 10, 0 ~ 5, 0 ~ 2.5,

0 ~ 1.25

0 ~ 10, 0 ~ 1, 0 ~ 0.1, 0 ~ 0.01

PCI-1710 PCI-1710HG

Gain CMRR Gain CMRR

0.5, 1 75dB 0.5, 1 75dB

2 80dB 10 90dB

4 84dB 100 106dB

8 84dB 1000 106dB

Chapter 1 General Information 5

• Maximum data throughput:

PCI-1710: 100 kHz

PCI-1710HG: (variable, depending on PGIA settling time)

PCI-1710HG

Gain Speed

0.5, 1 100 kHz

5, 10 35 kHz

50, 100 7 kHz

500, 1000 770 Hz

PCI-1710 PCI-1710HG

Gain Accuracy Gain Accuracy Remark

0.5, 1

0.01% of

FSR ±1 LSB

0.5, 1

0.01% of

FSR ±1 LSB

S.E./D*

2

0.02% of

FSR ±1 LSB

5, 10

0.02% of

FSR ±1 LSB

S.E./D

4

0.02% of

FSR ±1 LSB

50, 100

0.04% of

FSR ±1 LSB

D

8

0.04% of

FSR ±1 LSB

500, 1000

0.08% of

FSR ±1 LSB

D

• Accuracy: (depending on gain)

*S.E. = Single-ended D = Differential

• Linearity error: ±1 LSB

• Input impedance: 1 GΩ

• Trigger mode: Software, on-board programmable pacer or external

6 PCI-1710 /1710HG User's Manual

Analog Output:

• Channels: 2

• Resolution: 12-bit

• Relative accuracy: ±1/2 LSB

• Gain error: ±1 LSB

• Maximum update rate: 100 K samples/s

• Slew rate: 10 V/µs

• Output range: (software programmable)

With internal reference: 0 ~ +5 V, 0 ~ +10 V

With external reference: 0 ~ +x V @ -x V (-10 ≤ x ≤ 10)

Digital Input:

• Channels: 16

• Input voltage:

Low: 0.4 V max.

High: 2.4 V min.

• Input load:

Low: -0.2 mA @ 0.4 V

High: 20 µA @ 2.7 V

Digital Output:

• Channels: 16

• Output voltage:

Low: 0.4 V max. @ 8.0 mA (sink)

High: 2.4 V min. @ -0.4 mA (source)

Chapter 1 General Information 7

Programmable Timer/Counter

• Counter chip: 82C54 or equivalent

• Counters: 3 channels, 16 bits, 2 channels are permanently

configured as programmable pacers; 1 channel is free

for user application

• Input, gate: TTL/CMOS compatible

• Time base:

Channel 1:10 MHz

Channel 2:Takes input from output of channel 1

Channel 0:Internal 1 MHz or external clock (10 MHz max.)

selected by software.

General:

• I/O Connector: 68-pin SCSI-II female connector

• Power consumption: +5 V @ 850 mA (Typical),

+5 V @ 1.0 A (Max.)

• Dimensions: 175 mm x 107 mm (6.9” x 4.2”)

• Operating temperature: 0 ~ +60 °C (32 ~ 140 °F) ( refer to IEC 68-

2-1, 2 )

• Storage temperature: -20 ~ +70 °C (-4 ~ 158 °F)

• Operating humidity: 5 ~ 95%RH non-condensing ( refer to IEC 68-

2-3 )

• MTBF: over 64,770 hrs @ 25 °C, grounded, fixed environment

8 PCI-1710 /1710HG User's Manual

1.4 Block Diagram

Figure 1-1: PCI-1710/PCI-1710HG block diagram

PCI Controller

Address Decoder

16-bit Digital Output

16-bit Digital Input

12-bit D/A Output 0

12-bit D/A Output 1

Data Bus

PCIBus

A/D & D/A Status

Control Logic

4K Samples

FIFO

12-bit A/D

Convertor

IRQ Control

Logic

A/D Trigger

Logic

10 MHz

OSC

10 MHz/10=

1 MHz

PGIA

+

-

Gain Control RAM

Channel Scan Logic

Multiplexer

16 S/E

or

8 DIFF

COUNTER

2

COUNTER

1

COUNTER

0

AI15

AI0

AI1

EXT_TRG

CNT0_GATE

CNT0_OUT

CNT0_CLK

Address Bus

INT

PACER_OUT

Chapter 2 Installation 9

2

Installation

CHAPTER

10 PCI-1751/1710HG User's Manual

2.1 Initial Inspection

Before installing the PCI-1710/1710HG, check the card for visible

damage. We have carefully inspected the card both mechanically and

electrically before shipment. It should be free of marks and in perfect

order upon receipt.

As you unpack the PCI-1710/1710HG, check it for signs of shipping

damage (damaged box, scratches, dents, etc.). If it is damaged or fails

to meet specifications, notify our service department or your local

sales representative immediately. Also, call the carrier immediately and

retain the shipping carton and packing materials for inspection by the

carrier. We will then make arrangements to repair or replace the unit.

2.2 Unpacking

The PCI-1710/1710HG contains components that are sensitive and

vulnerable to static electricity. Discharge any static electricity on your

body to ground by touching the back of the system unit (grounded

metal) before you touch the board.

Remove the PCI-1710/1710HG card from its protective packaging by

grasping the card's rear panel. Handle the card only by its edges to

avoid static discharge which could damage its integrated circuits.

Keep the antistatic package. Whenever you remove the card from the

PC, protect the card by storing it in this package.

You should also avoid contact with materials that hold static electricity

such as plastic, vinyl and styrofoam.

Check the product contents inside the packing. There should be one

card, one CD-ROM, and this manual. Make sure nothing is missing.

Chapter 2 Installation 11

2.3 Installation Instructions

The PCI-1710/1710HG can be installed in any PCI slot in the

computer. However, refer to the computer user's manual to avoid any

mistakes and danger before you follow the installation procedure

below:

1. Turn off your computer and any accessories connected to the

computer.

Warning! TURN OFF your computer power supply whenever

you install or remove any card, or connect and

disconnect cables.

2. Disconnect the power cord and any other cables from the back of

the computer.

3. Remove the cover of the computer.

4. Select an empty 5 V PCI slot. Remove the screw that secures the

expansion slot cover to the system unit. Save the screw to secure

the interface card retaining bracket.

5. Carefully grasp the upper edge of the PCI-1710/1710HG. Align the

hole in the retaining bracket with the hole on the expansion slot and

align the gold striped edge connector with the expansion slot socket.

Press the card into the socket gently but firmly. Make sure the card

fits the slot tightly.

6. Secure the PCI-1710/1710HG by screwing the mounting bracket to

the back panel of the computer.

7. Attach any accessories (68-pin cable, wiring terminal, etc.) to the

card.

8. Replace the cover of your computer. Connect the cables you

removed in step 2.

9. Turn the computer power on.

12 PCI-1751/1710HG User's Manual

Chapter 3 Signal Connections 13

3

Signal Connections

CHAPTER

14 PCI-1710/1710HG User's Manual

3.1 Overview

Correct signal connections are one of the most important factors in

ensuring that your application system is sending and receiving data

correctly. A good signal connection can avoid much unnecessary and

costly damage to your valuable PC and other hardware devices. This

chapter will provide some useful information about how to connect

input and output signals to the PCI-1710/1710HG card via the I/O

connector.

3.2 I/O Connector

The I/O connector for the PCI-1710/1710HG card has 68 pins that you

can connect to 68-pin accessories with the PCL-10168 shielded cable.

Note! The PCL-10168 shielded cable is specially designed

for the PCI-1710/1710HG for reducing noise in the

analog signal lines. Its wires are all twisted pairs,

and the analog lines and digital lines are seperately

shielded, providing minimal cross talk between

signals and the best protection against EMI/EMC

problems.

Pin Assignment

Figure 3-1 shows the pin assignments for the 68-pin I/O connector on

the PCI-1710/1710HG card.

Chapter 3 Signal Connections 15

Figure 3-1: I/O connector pin assignments for the PCI-1710/1710 HG card

AI0

AI2

AI4

AI6

AI8

AI10

AI12

AI14

AIGND

DA0_REF

DA0_OUT

AOGND

DI0

DI2

DI4

DI6

DI8

DI10

DI12

DI14

DGND

DO0

DO2

DO4

DO6

DO8

DO10

DO12

DO14

DGND

CNT0_CLK

CNT0_OUT

CNT0_GATE

+12V

68

67

66

65

64

63

62

61

60

59

58

57

56

55

54

53

52

51

50

49

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

AI1

AI3

AI5

AI7

AI9

AI11

AI13

AI15

AIGND

DA1_REF

DA1_OUT

AOGND

DI1

DI3

DI5

DI7

DI9

DI11

DI13

DI15

DGND

DO1

DO3

DO5

DO7

DO9

DO11

DO13

DO15

DGND

PACER_OUT

TRG_GATE

EXT_TRG

+5V

16 PCI-1710/1710HG User's Manual

I/O Connector Signal Descriptions

Signal

Name

Reference Direction Description

AI<0…15> AIGND Input

Analog Input Channels 0 through 15. Each

channel pair, AI<i, i+1> (i = 0, 2, 4...14), can be

configured as either two single-ended inputs or

one differential input.

AIGND - -

Analog Input Ground

. These pins are the

reference points for single-ended

measurements and the bias current return point

for differential measurement. The three ground

references (AIGND, AOGND, and DGND) are

connected together on the PCI-1710/1710HG

card.

DA0_ REF AOGND Input

Analog Output Channel 0 External

Reference. This is the external reference input

for the analog output channel 0 circuitry.

DA1_ REF AOGND Input

Analog Output Channel 1 External

Referenc

e. This is the external reference input

for the analog output channel 1circuitry.

DA0 _OUT AOGND Output

Analog Output Channel 0. This pin supplies

the voltage output of analog output channel 0.

DA1 _OUT AOGND Output

Analog Output Channel 1. This pin supplies

the voltage output of analog output channel 1.

AOGND - -

Analog Output Ground. The analog output

voltages are referenced to these nodes. The

three ground references (AIGND, AOGND, and

DGND) are connected together on the PCI-

1710/1710HG card.

Page is loading ...

Advantech Computer Hardware PCI-1710 User manual

This manual is also suitable for

Advantech Computer Hardware PCI-1710 User manual

Related papers

Other documents