Furniture of America IDF-4848-3PK Installation guide

Brand
Furniture of America
Model
IDF-4848-3PK
Type
Installation guide
EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM4848-3PK
Assembly Instructions
Tools Required for Assembly:
Rev.14-10-20
Page 1 of 8
DIFFICULT
ASSEMBLY RATING
Allen Wrench
2 PERSONS RECOMMENDED
(Included)
Page 2 of 8
Parts List
Hardware List
#1 x 1 pc
C/T Cross Stand A
#2 x 1 pc
C/T Cross Stand B
#3 x 1 pc
C/T Stand B Support
#A x 3 pcs
Bolt 1/4”x2”
#B x 1 pc
Bolt 1/4”x7/8”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 2 pcs
Flat Washer M12
MD
#D x 2 pcs
Flat Washer M16
#4 x 1 pc
C/Table Glass Top
Page 3 of 8
#E x 4 pcs
Lock Washer
#F x 1 pc
Allen Wrench
#G x 4 pcs
Suction Cup
Due to the size and/or weight of this product,
it is highly recommended that the assembly
should be done near the area of its intended
location. Make sure you have enough space
to move around during the assembly.
ALWAYS have at least two people to help
with transporting and assembling the product
to avoid any potential injury and/or damage.
#H x 2 pcs
Bolt Cover
Page 4 of 8
I. Align the coffee table stand B
support (#3) with the pre-
drilled holes of the coffee
table cross stand B (#2).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt
(#A) and then the flat washer
(#C) onto the SAME bolt
(#A), in that order.
III. Insert the bolt assemblies
through the coffee table
cross stand B (#2) using the
Allen wrench (#F) to lock
them with the coffee table
stand B support (#3) follow
by 2 bolt covers (#H).
#A x 1 pc
#D x 1 pc
#E x 1 pc
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
I. Align the coffee table cross
stand B (#2) with the pre-drilled
hole of the coffee table cross
stand A (#1).
II. Prepare a bolt assembly by
inserting FIRST the lock
washer (#E) onto the bolt #A)
and then the flat washer (#D)
onto the SAME bolt (#A), in
that order.
III. Insert the bolt assembly
through the coffee table cross
stand A (#1) using the Allen
wrench (#F) to lock it with the
coffee table cross stand B (#2).
#A x 2 pcs
#C x 2 pcs
#E x 2 pcs
#H x 2 pcs
.
I. Insert 4 suction cups (#G)
into the coffee table cross
stand A (#1) and coffee table
cross stand B (#2).
II. Carefully place the glass top
(#4) on top of the suction
cups (#G). The glass top
should be evenly centered
and rested flat.
III. Make sure the table is rested
on a flat surface and does
not feel loose or wobbly. If it
does, double check that the
bolts/screws are secured and
properly tightened.
Turn right (clockwise) to tighten
Page 5 of 8
COFFEE TABLE ASSEMBLY IS COMPLETED
#B x 1 pc
#D x 1 pc
#E x 1 pc
I. Prepare a bolt assembly by inserting FIRST the lock washer (#E)
onto the bolt (#B) and then the flat washer (#D) onto the SAME bolt
(#B), in that order.
II. Insert the bolt assembly through the coffee table stand B support
(#3) using the Allen wrench (#F) to lock it with the coffee table
cross stand A (#1).
#G x 4 pcs
#3
Parts List
Hardware List
#1 x 2 pcs
E/T Cross Stand A
#2 x 2 pcs
E/T Cross Stand B
#3 x 2 pcs
E/T Stand B Support
#A x 6 pcs
Bolt 1/4”x2”
#B x 2 pcs
Bolt 1/4”x7/8”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 4 pcs
Flat Washer M12
MD
#D x 4 pcs
Flat Washer M16
#4 x 2 pcs
E/Table Glass Top
Page 6 of 8
#E x 8 pcs
Lock Washer
#F x 1 pc
Allen Wrench
#G x 8 pcs
Suction Cup
#H x 4 pcs
Bolt Cover
X 2
Page 7 of 8
I. Align the end table stand B
support (#3) with the pre-
drilled holes of the end table
cross stand B (#2).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt #A)
and then the flat washer (#C)
onto the SAME bolt (#A), in
that order.
III. Insert the bolt assemblies
through the end table cross
stand B (#2) using the Allen
wrench (#F) to lock them
with the end table stand B
support (#3) follow by 2 bolt
covers (#H).
#A x 2 pcs
#D x 2 pcs
#E x 2 pcs
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
I. Align the end table cross stand
B (#2) with the pre-drilled hole
of the end table cross stand A
(#1).
II. Prepare a bolt assembly by
inserting FIRST the lock
washer (#E) onto the bolt #A)
and then the flat washer (#D)
onto the SAME bolt (#A), in
that order.
III. Insert the bolt assembly
through the end table cross
stand A (#1) using the Allen
wrench (#F) to lock it with the
end table cross stand B (#2).
#A x 4 pcs
#C x 4 pcs
#E x 4 pcs
#H x 4 pcs
.
I. Insert 4 suction cups (#G)
into the end table cross
stand A (#1) and end table
cross stand B (#2).
II. Carefully place the glass top
(#4) on top of the suction
cups (#G). The glass top
should be evenly centered
and rested flat.
III. Make sure the table is rested
on a flat surface and does
not feel loose or wobbly. If it
does, double check that the
bolts/screws are secured and
properly tightened.
Turn right (clockwise) to tighten
Page 8 of 8
END TABLE ASSEMBLY IS COMPLETED
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
I. Prepare a bolt assembly by inserting FIRST the lock washer (#E)
onto the bolt (#B) and then the flat washer (#D) onto the SAME bolt
(#B), in that order.
II. Insert the bolt assembly through the end table stand B support (#3)
using the Allen wrench (#F) to lock it with the end table cross stand
A (#1).
#G x 8 pcs
#3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Furniture of America IDF-4848-3PK Installation guide

Brand
Furniture of America
Model
IDF-4848-3PK
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents