eLEDing EE820W-SFBS User manual

Brand: eLEDing

Model: EE820W-SFBS

Type: User manual

Lighting Profile Setup & Battery Change: open the bottom cover (Fig. 2)

Battery change: unplug the old battery and replace it with the new battery. Noted that the battery plug only fit in one way.

VR1: adjust dimming brightness (from 5-50% of max brightness, turn clockwise to increase brightness), minimum set is recommended.

VR2: adjust sensor range (can be adjusted from 10 - 50 ft, turn counterclockwise to decrease sensitivity range)

Notes: increasing dimming brightness & sensitivity may reduce the length of illumination period, especially during wintertime

Installation Guidelines

1. Securely mount the unit on the light pole or wall, adjust the light head direction and angles based on your need (Fig.4)

2. Solar Panel must be mounted in a non-obstructed position that allows at least 5-6 hours direct sunlight all year round. For most of the North

America projects, adjust the tilt of the solar panel at 25°- 45° degrees based on your actual location. If you are close to equator’s location, a flat

installation (light head is parallel to the ground) will be enough.

The solar panel can be pointed to east, west and south but definitely not to north.

For northern hemisphere installations, a south-facing position is best and visa-versa for southern hemisphere installation.

Optional AUX DC power sources can be used as back-up power source or charging enhancement device, to give the light a quick charge before

installation or during low power due to critical weather (Fig. 1).

3. Solar Panel Maintenance: Use soft, wet cloth to clean the solar panel periodically (at least once a one year) to avoid energy output reduction

resulted from accumulated dust. Clean accumulated snow ASAP during snowing season.

Rev: 08152019

ON/OFF

AUX for:

External solar panel

USB Adaptor 12-24V, 2A

Power Bank

Recommend

to charge 1-2

days before

installation,

switch in OFF

position

light

blink

once

5-min walk

test mode

5-10 sec

Motion

Yes

Light ON

Light OFF

5 min

Daytime?

Light On

Yes

Light

OFF

Light turns ON

When

nighttime

comes

Thank you for choosing eLEDing!

This product is designed to provide long lasting superior illumination by using environment-friendly Solar-Hybrid, Lithium-based energy

before installation, comply with local standard and regulations of construction & electrical/electronic projects, follow the safety guidelines to

prevent any possible accidents, incident and/or injuries. Consult experienced contractor/installer and electrical technicians for assistance.

Push

Switch

One Step Setup (Just 1 Click!)

Default

Setting

Put Jumper 2 (J2) at

Close position as

option

SMART 2 Mode

SMART lighting profile

(Fig.2 & 3)

Dimming brightness

until dawn

Dusk to Dawn with

dimming brightness

Full brightness

After 3 hours

come to full

brightness

Recommend for areas

with busy traffic and

sufficient sunlight all

year round.

Recommend for

high-latitude, long

winter areas with

low traffic.

Motion

detected

Motion

detected

If low power

(20% left)

ON with full

brightness

Motion

Switch to

AUTO Mode

Light OFF

Yes

Full Charge

Back to SMART Mode

Critical Reserve

(10% left)

ON with half

brightness

Motion

Light OFF

Yes

Intelligence Power Management (IPM) system : monitor & adjust power consumption

SMART 1 Mode

If change lighting profile

12346 Valley Blvd, #A, El Monte, CA 91732 Phone Number: 1-877-579-3889 Fax: 626-452-9194 Web: www.eleding.com/www.eesgi.com

After Full

Charge

EESGI guarantees this product to be free from defects in material &

workmanship for (1) year.

This warranty does not apply to damage from misuse or incorrect installation/

connection.

This warranty does not cover accessories, bulbs, batteries, high voltage

accidents, alterations, unauthorized use or repair, neglect, misuse, abuse,

damages or defects resulting from normal wear and tear (including chips,

fading scratches, abrasions or discoloration due to usage or sun exposure), or

failure to follow instructions for care and maintenance, fire, flood, and Acts of

God.

This warranty does not include liability for incidental or consequential

damages.

EESGI is not responsible for any damages in excess of the retail purchase

price of the product under any circumstances. The consumer is responsible

for the installation of, removal of, and reinstallation of the product.

One Year Limited Warranty

Specifications EE810W-SH10 EE815W-SH15 EE820W-SH20

Outdoor Application Rating IP65

CREE LED Number 1 pc 2 pcs 2 pcs

CREE LED Emitter output

(Max on peak)

10W 15W 20W

Illumination brightness

(Lumen on peak)

1600 2400 3200

CREE LED illumination color 5000K 5000K 5000K

Li-Poly Battery Pack 50WH 100WH 120WH

Intelligent power management Yes

Dim Brightness (adjustable) 50-800+ lumen 75-1000+ lumen 100-1500+ lumen

Sensitivity Coverage (adjustable) 10-50 ft 10-50 ft 10-50 ft

Mono-crystalline Tempered Glass

Solar Panel

10W, 15V 15W, 15V 22W, 15V

Light Size (L x W x H) 14.5"x11"x1.75" 25"x11"x1.75" 35"x11"x1.75"

Unit Weight (lbs) 13 19 26

Mounting Tube Adapter Yes

Mounting Adaptor Diameter 2''-7/16 (2.3"-2.44")

Package Weight (lbs) 14.5 22 30

Package Size (L x W x H) 16.5"x14"x7" 26.5"x14"x7" 38"x14"x7"

Aux Solar Panel/DC Adapter Optional, 12-24V DC/≤2A

Charging Time 9-10 hrs

Operation Temperature (- 4°F to +125°F)

Certificate & Compliance FCC Part 15 Class B and ICES-003:2004

Rev:08152019

Fig 7. Mounting Height & Diameter of Area Coverage (ft)

Fig 6. Height & PIR Profile

12346 Valley Blvd, #A, El Monte, CA 91732 Phone Number: 1-877-579-3889 Fax: 626-452-9194 Web: www.eleding.com/www.eesgi.com

eLEDing EE820W-SFBS User manual

eLEDing EE820W-SFBS User manual

eLEDing EE820W-SFBS User manual

Related papers

Other documents