Rhino Rack RHINO-RACK RX100 RX Raised Leg Kit Operating instructions

RHINO-RACK RX100 RX Raised Leg Kit
Rhino Rack
Brand
Rhino Rack
Model
RHINO-RACK RX100 RX Raised Leg Kit
Type
Operating instructions

Rhino Rack RHINO-RACK RX100 RX Raised Leg Kit is designed to provide a sturdy and elevated platform for mounting crossbars on your vehicle's roof rails. With a weight capacity of up to 220 lbs, it can accommodate a wide range of cargo, from kayaks and bikes to rooftop tents and luggage boxes. The kit includes four leg assemblies and a torque tool, making installation quick and easy. Whether you're an outdoor enthusiast or simply need extra storage space, the Rhino Rack RX100 RX Raised Leg Kit is a versatile and reliable solution for your cargo carrying needs.

Rhino Rack RHINO-RACK RX100 RX Raised Leg Kit is designed to provide a sturdy and elevated platform for mounting crossbars on your vehicle's roof rails. With a weight capacity of up to 220 lbs, it can accommodate a wide range of cargo, from kayaks and bikes to rooftop tents and luggage boxes. The kit includes four leg assemblies and a torque tool, making installation quick and easy. Whether you're an outdoor enthusiast or simply need extra storage space, the Rhino Rack RX100 RX Raised Leg Kit is a versatile and reliable solution for your cargo carrying needs.

Leg Instructions
RX100
Rhino-Rack AUSTRALIA
22A Hanson Pl,
Eastern Creek, NSW, 2766
Rhino-Rack USA
Unit D, 2450 Airport Blvd,
Aurora, CO, 80011
Doc. No: 520-RFI-00098
Issue No: 03
Issue Date: 08/02/2023
RHINORACK.COM
Important:
1. Check the Rhino-Rack website to ensure you have the latest issue of these instructions.
2. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations.
3. Check the contents of kit before commencing fitment and report any discrepancies.
4. Place these instructions in the vehicle’s glove box after installation is complete.
5. These instructions must be followed for warranty to be upheld.
Fit Time: 15 mins
For additional Pioneer Vehicle Fitting Information
refer to your vehicle’s online supplement sheet.
VEHICLE
OWNER’S
MANUAL
ROOF LOAD
LIMIT
DYNAMIC LOAD LIMIT
X
VEHICLE HEIGHT ADDED (mm/in)
BAR NO. A B C D E F G
DIMENSION (CM)
SPACERS REQ’D
CONNECTOR BACKBONE BACKBONE BACKBONE
REAR
FRONT
+-
CA E
BAR D
BAR B
UNDERBAR SPACING
REGION AUS NZ USA CA SA UK EU ZA
AVAILABILITY  
RUNNING
DATES 2015 - 2015 - - - - - - 2015 -
VEHICLE PIONEER CONNECTOR HEIGHT ADDED (mm/in)
XXX/XX
VEHICLE
NOTES - Do not operate sunroof
XXX Kg
XXX lbs
XX Kg
XX lbs
XXX Kg
XXX lbs
*VEHICLE
MANUFACTURER’S
ROOF LOAD LIMIT
OR
Max
kg
UP TO UP TO
VISIT THE ONLINE
CALCULATOR FOR
CURRENT SYSTEM
LOAD LIMIT DATA
TOTAL STATIC LOAD LIMIT: UP TO
DYNAMIC LOAD LIMIT (ON AND OFF-ROAD):
*USE THE VEHICLE MANUFACTURER’S MAXIMUM ROOF ALLOWANCE IF IT IS LOWER THAN THE FIGURE LISTED
CARGO SYSTEM WEIGHT
LOAD LIMIT
PIONEER VEHICLE FITTING INFORMATION
rhinorack.com
kg / lbs
kg / lbs kg / lbs kg / lbs
kg / lbs kg / lbskg / lbs kg / lbs
kg / lbs
kg / lbs
kg / lbs
kg / lbs kg / lbs kg / lbs
kg / lbs kg / lbskg / lbs kg / lbs
kg / lbs
kg / lbs
Avoid point loads concentrated at
the front or rear.
Distribute loads evenly and laterally/longitudinally as low as possible over the span.
!
Exercise extreme care when transporting wind-resistant loads.
Special consideration must be taken when cornering and braking.
Off-road conditions can be much more rigorous.
Extreme care must be taken on any driven path that does
not contain a surface protection layer (tar/bitumen).
Page 2 of 12
RX100 // MAKE SPACE FOR ADVENTURE
TAP HERE
Do NOT obstruct windscreen camera sensors Warranty for roof rack system will
be void if the front of the kayak is not
secured to the bonnet
Long flexible loads must attach securely to rigid
support and be tied down to the bonnet
!
Use only non-stretch fastening
ropes or straps to attach cargo to
roof racks
Loads must be tied down to
Platform, NOT around legs
Page 3 of 12
RX100 // MAKE SPACE FOR ADVENTURE
Surfboard Overhang > 600mm must be
tied to the bonnet
Racks must be
removed when vehicle
is put through an
automatic car wash.
Ensure sunroof will not collide
with roof rack system.
Ensure Ladder is
well supported on the
ground to support tent.
Take extreme caution
when climbing heights
above 1.2m/4ft.
Youtube.com/Rhinorackaustralia
!
!
!
Tub/tray/canopys can move independently from the vehicle cabin. Rigidly fix to either the cabin roof racks or the tub/tray/
canopy roof racks but not both simultaneously.
Page 4 of 12
RX100 // MAKE SPACE FOR ADVENTURE
TAP HERE
Note for Dealers and Fitters
It is your responsibility to ensure these fitting instructions are given to the end user or client. These instructions remain the property
of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
• All bolt connections should be checked after driving a short distance (5-10 mins street roads) when you first install your roof
racks.
• All bolted connections should be checked again at regular intervals (weekly is recommended, depending on road conditions,
usage, loads and distances travelled).
• All bolted connections should be checked each time they are re-fitted.
• Off-road conditions are more rigorous. Check all bolted connections and your load more regularly.
• Ensure that your vehicle manufacturer’s GVM, and gross axle weights are not exceeded (refer to vehicle owner’s manual).
In service maintenance checks
Torque Settings:
Unless stated otherwise in these
instructions, all fasteners should be
set to the following torque settings:
4-5Nm 8-10Nm 16-18Nm
3-4lbs/ft 6-7.5lbs/ft 12-13lbs/ft
M6 M8 M10
4-5Nm
3-4lbs/ft
M6 8-10Nm
6-7.5lbs/ft
M8 16-18Nm
12-13lbs/ft
M10
4-5Nm
3-4lbs/ft
M6 8-10Nm
6-7.5lbs/ft
M8 16-18Nm
12-13lbs/ft
M10
Carrying Capacity
*VEHICLE
MANUFACTURER’S
ROOF LOAD LIMIT
OR
Max
kg
UP TO UP TO
DYNAMIC LOAD LIMIT (On and Off-road) :
CARGO SYSTEM WEIGHT LOAD LIMIT
*USE THE VEHICLE MANUFACTURER’S MAXIMUM ROOF ALLOWANCE IF IT IS LOWER THAN THE FIGURE LISTED
95 KG
209 lbs
5 KG
11 lbs
100 KG
220 lbs
STATIC LOAD LIMIT: UP TO 250KG / 551LBS*
Check the website and the vehicle owners hand book for your vehicle manufacturer’s maximum carrying capacity.
Load must be evenly distributed over the system.
VISIT THE ONLINE
CALCULATOR FOR
CURRENT SYSTEM
LOAD LIMIT DATA
System Weight
Total weight of the roof
rack system.
(e.g. Crossbars,
Backbone, Platform)
Max System Load Capacity
Please ensure you use the vehicle
manufacturer’s maximum roof
allowance if it is lower than the figure
listed in the fitting chart/supplement.
Vehicle Manufacturer’s
Load Limit
Total permissible weight
attached to the roof of the car.
This is inclusive of the weight
of the roof rack system.
Cargo Load Limit
Total permissible weight
allowed on top, and attached
to roof racks whilst the
vehicle is in motion.
TOOLS REQUIRED:
T1 - Tape Measure
T2 - Marker / Pencil
T3 - Knife or Scissors
Parts List
Leg Assembly Torque Tool
Max
kg
Max
kg
Max
kg
Page 5 of 12
RX100 // MAKE SPACE FOR ADVENTURE
x4
Ax1
B
SIDE VIEW
A
VA BARS:
For POST 2022 MODELS Skip to Step
Skip to Step after installing RX100 into underbars.
PLATFORMS:
Proceed to Pioneer Platform Instructions and your vehicle-specific Pioneer Fit Chart
sheet before installing legs into the Platform.
13
16
Page 6 of 12
RX100 // MAKE SPACE FOR ADVENTURE
1
2
1. Complete
VIEW FITTING CHART
Example only
Fit my vehicle journey
2. Select your Product Solution
3. Scroll down to ‘Product Details’
4. Download instructions under the
‘INSTRUCTIONS’ tab
rhinorack.com/roof
=
=
90°
90°
90°
90°
700 - 800mm
(27,9/16”- 31,1/2”)
Front edge
of Rail
Front edge
of Rail
REAR
FRONT
WINDSCREEN
T1
SIDE VIEW
TOP VIEW:
Page 7 of 12
RX100 // MAKE SPACE FOR ADVENTURE
3
4
5
Incrementally tighten each leg so that crossbars are firmly set in position.
While incrementally tightening legs, check bar/platform overhang is still equidistant
NOTE: Check rubber
gasket is correctly
sealed with roof rail.
B B
=
=
= =
T1
FRONT VIEW
T1 T1
TIGHTEN
B
Page 8 of 12
RX100 // MAKE SPACE FOR ADVENTURE
6
7
T2
LOOSEN B
Ensure inner sliding clamps
do not shift position while
tilting crossbars
!!
Ensure inner clamps
are flush with inner
surface of rail.
Slide outwards
Remain
fixed
Page 9 of 12
RX100 // MAKE SPACE FOR ADVENTURE
8
10
9
11
“0mm”
Centre of Bar
T2
T3
T1
X mm
X mm
rhinorack.com/roof
For POST 2022 Vehicles:
Refer to Fit Sheet for underbar
strip dimensions and cut to size
For PRE 2022 Vehicles:
Measure and cut underbar strips
Page 1 of 1
RX100 SUPPLEMENT SHEET
rhinorack.com
Rhino-Rack AUSTRALIA
22A Hanson Pl,
Eastern Creek, NSW, 2766
Rhino-Rack USA
Unit D, 2450 Airport Blvd,
Aurora, CO, 80011
Doc. No: 520-RFI-000XX
Issue No: 01
Issue Date: 25/07/2022
Proceed to Step 12 of the instructions before installing to vehicle roof rails.
Proceed to Step 12 of the instructions to complete installation.
1
FRONT REAR
LEG KIT
LEG KIT
167 mm
177 mm
REGION AUS NZ USA CA SA UK EU ZA
AVAILABILITY
RUNNING
DATES 2022 - 2022 - - - - - - -
HEIGHT ADDED (mm/in)
VEHICLE
NOTES
MEASUREMENT STRIPS
CROSSBAR DETAILS
FORD RANGER T6.2 WILDTRAK DOUBLE CAB
140 mm /
5 1/2in
700 mm /
27 9/16in
Page 10 of 12
RX100 // MAKE SPACE FOR ADVENTURE
12
14
13
For Pre 2022 Vehicles:
Crossbars: Realign to Step markings
OR
Platforms: Refer to your vehicle-specific
Pioneer Fit Chart for rail positioning
Incrementally tighten each leg so that crossbars/platforms are firmly set in position.
While incrementally tightening legs, check bar overhang is still equidistant
For Pioneer Platforms, proceed to step
NOTE: Check rubber
gasket is correctly
sealed with roof rail.
B B
=
=
5-6Nm
6.5-8LB/FT
5-6Nm
6.5-8LB/FT
For POST 2022 Vehicles:
Refer to vehicle-specific Crossbar
Supplement/Pioneer Fit Chart for
rail positioning
8
20
Page 11 of 12
RX100 // MAKE SPACE FOR ADVENTURE
16
15
17
Check fitment is secure before use
T3
UNDERSIDE
VIEW:
Page 12 of 12
RX100 // MAKE SPACE FOR ADVENTURE
19
18
20
21
!
Ensure the leg hooks tightly under the roof rails
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Rhino Rack RHINO-RACK RX100 RX Raised Leg Kit Operating instructions

RHINO-RACK RX100 RX Raised Leg Kit
Rhino Rack
Brand
Rhino Rack
Model
RHINO-RACK RX100 RX Raised Leg Kit
Type
Operating instructions

Rhino Rack RHINO-RACK RX100 RX Raised Leg Kit is designed to provide a sturdy and elevated platform for mounting crossbars on your vehicle's roof rails. With a weight capacity of up to 220 lbs, it can accommodate a wide range of cargo, from kayaks and bikes to rooftop tents and luggage boxes. The kit includes four leg assemblies and a torque tool, making installation quick and easy. Whether you're an outdoor enthusiast or simply need extra storage space, the Rhino Rack RX100 RX Raised Leg Kit is a versatile and reliable solution for your cargo carrying needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents