TH210-VI
Quick Reference
Warranty Information
Diebold Nixdorf guarantees a limited warranty
engagement for 12 months beginning with the date of
delivery. This warranty engagement covers all those
damages which occur despite a normal use of the product.
Damages because of
- improper or insufficient maintenance,
- improper use of the product or unauthorized
modifications of the product,
- inadequate location or surroundings
will not be covered by the warranty.
Manufacturers Certification
The
device complies with the requirements of
the directive 2004/108/EC with regard to
‘Electromagnetic compatibility" and 2006/95/EC
“Low Voltage Directive” and RoHS directive
2011/65/EU.
Therefore, you will find the CE mark on the
device or packaging.
Underwriters Laboratories
In addition, the device has received
the UL symbol and cUL symbol.
Federal Communications Commission (FCC)
Radio Frequency Interference Statement
Warning
Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
Note
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
Information to the User
This equipment must be installed and used in strict accordance
with the manufacturer’s instructions. However, there is no
guarantee that interference to radio communications will not
occur in a particular commercial installation. If this equipment
does cause interference, which can be determined by turning the
equipment off and on, the user is encouraged to contact Diebold
Nixdorf immediately. Diebold Nixdorf is not responsible for any
radio or television interference caused by unauthorized
modification of this equipment or the substitution or attachment
of connecting cables and equipment other than those specified by
Diebold Nixdorf. The correction of interferences caused by such
unauthorized modification, substitution or attachment will be the
responsibility of the user.
This class A digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe A est conforme à la norme
NMB-003 du Canada.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation.
Unpack the Printer
Unpack the printer, saving all packing materials for future
shipping or storage.
Changing the paper roll
Connect the cables
Depending on your printer configuration, the connector
panel may vary from the illustration.
Connector interface panel
optional
e.g. RS-232C
Communication
Connector
USB
Connector
Power Supply
Connector
Cash
Drawer
Connector
Route the cables
Do not connect USB and RS-232C at the same time.
Run a diagnostic test print
Configure the printer if necessary
Safety instructions
Do not touch the printer’s cutter and tear bar.
The print head is a thermal element and it is at high
temperature during printing or just after operation.
Therefore, do not touch it and its peripherals for
safety reasons.
The thermal head is an ESD
-
sensitive device. To
prevent damage, do not touch either its printing part
or connecting parts.
Caution:
Install the printer on a flat and stable place.
Reserve adequate space around the printer so that
convenient operation and main-tenance can be
performed.
Keep the printer away from water source.
Do not use or store the printer in a place exposed to
heat or fire, moisture, serious pollution and direct
sunlight.
Do not place the printer on a place exposed to vibration
or impact.
No dew condensation is allowed to the printer. In case
of such condensation, do not turn on the power until
condensation completely disappeared.
Only use power supply units and cables released by
Diebold Nixdorf.
Connect the printer to “UL Listed Computers” only.
Only connect cables to the 24V connector which are
marked with DP-1 or DP-2.
The printer should only be disassembled or repaired by a
technician who is certified by the manufacturer.
Further Information
Please find detailed information about the printer in the
Operator’s Guide. That document as PDF file and needed
drivers can be downloaded from this web site:
http://www.Dieboldnixdorf.com
Copyright© Diebold Nixdorf
The reproduction, transmission or use of this document or its
contents is not permitted without express authority.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration
of a utility model or design, are reserved.
Delivery subject to availability; technical modifications possible.
Order No. 01750275754 C
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Diebold Nixdorf TH250 Operating instructions
-
Wincor Nixdorf K-two User manual
-
Wincor Nixdorf BEETLE /iSCAN EASY Non Cash Installation guide
-
Wincor Nixdorf BEETLE iSCAN EASY EXPRESS PLUS User manual
-
-
Wincor Nixdorf BEETLE /iPOS plus Advanced User manual
-
-
-
-
Other documents
-
-
-
-
-
-
-
-
-
Wincor Nixdorf BEETLE /iSCAN EASY eXpress+ User manual
-