Knightsbridge HBLU1 User manual

Brand: Knightsbridge

Model: HBLU1

Type: User manual

Knightsbridge HBLU1 is a versatile bracket designed for easy and secure installation of HBL fittings. With its sturdy construction, it offers reliable support for your lighting fixtures. Installation is a breeze with the included expansion bolts and Allen screws. Simply mark the fixing holes, drill, tap in the bolts, and mount the bracket. Then, attach your HBL fitting to the bracket, and you're good to go. Whether you're upgrading your home lighting or adding accent lights to your commercial space, the Knightsbridge HBLU1 bracket has you covered.

122

INSTALLATION & MAINTENANCE MANUAL

HBLU (bracket for HBL ﬁttings)

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following products:

HBLU1 / HBLU2

GENERAL INSTRUCTIONS

INSTALLATION

Fig 1

Fig 2

• Using the bracket as a template, mark the location of the ﬁxing holes, drill 2x 10mm holes ensuring

not to infringe with any joists, gas or water pipes or electrical cables

• Using a hammer, tap the expansion bolts into the 10mm ﬁxing holes (see Fig 1)

• Tighten expansion bolt nuts but allow enough space for the bracket to mount

• Remove the driver housing via the 4 Allen screws (see Fig 2)

• Align the mounting bracket with 2 of the driver housing screw pillars (see Fig 3)

HBLseries

Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand

maintenance.

Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:

HBL100/HBL150/HBL200/HBL240



SAFETY

• Installationofthisluminaireshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe

latestBuildingandcurrentIEEWiringRegulations(BS7671)

• Pleaseisolatemainspriortoinstallation/maintenance

• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe

circuitcable,fuseorcircuitbreaker

• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation

• ThisproductseriesisClassIandrequiresanearth

• ThisproductseriesisIP65rated(recommendedindooruseonly)

• Thisproductisdimmableviaa1-10Vdimmer

INSTALLATION

Providepowertotherequiredpointofinstallation.SuitableIPratedjunctionsboxesshouldbeusedwhere

required



Suspensionmounting

Tosuspendthefitting,screwthemountinghoopintothetopoftheluminaire(seeFig1)



Fig1



Bracketmounting

Usingthebracketasatemplate,markthelocationofthefixingholes,drill2x10mmholesensuringnotto

infringewithanyjoists,gasorwaterpipesorelectricalcables

Usingahammer,taptheexpansionboltsintothe10mmfixingholes(seeFig2)



Fig2

Screwdown

mountinghoop

Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount

Removethedriverhousingviathe4Allenscrews(seeFig3)





Fig3



Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)



Fig4



PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown

the4Allenscrews(seeFig5)

Fig5

Removethe4Allenscrews

FastendownAllenscrews

Fig 3

Fig 4

Fig 5

• Position the driver housing into the bracket ensuring all Allen screw holes are correctly aligned and

fasten down the 4 Allen screws (see Fig 4)

• Lift the ﬁtting up to the expansion bolts and slide into the bracket (see Fig 5)

• Tighten the 2 expansion bolts to secure the luminaire to the surface

Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount

Removethedriverhousingviathe4Allenscrews(seeFig3)





Fig3



Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)



Fig4



PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown

the4Allenscrews(seeFig5)

Fig5

Removethe4Allenscrews

FastendownAllenscrews

Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount

Removethedriverhousingviathe4Allenscrews(seeFig3)





Fig3



Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)



Fig4



PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown

the4Allenscrews(seeFig5)

Fig5

Removethe4Allenscrews

FastendownAllenscrews

Liftthefittinguptotheexpansionboltsandslideintothebracket(seeFig6)



Fig6



Tightenthe2expansionboltstosecuretheluminairetothesurface



Towiretheluminairewithoutadimmer(seefig7)



Fig7



Towiretheluminairewitha1-10Vdimmer(seeFig8)



Live-brown

Earth–green/yellow

Neutral-blue

Blue:Dim+

White:Dim-

Neutral-blue

Earth–green/yellow

Live-brown

ML Accessories Limited

LU5 5TA

www.mlaccessories.co.uk SBFEB17_V2

GENERAL

WARNING

WARRANTY

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may

damage the product.

Do not use any source of high pressure washers to maintain or clean this product.

Ensure correct ﬁxtures are used for the surface that the product is ﬁxed to.

This product has a warranty of 5 years from date of purchase. Failure to install this product in

accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of

the batch codes will invalidate the warranty. If this product should fail within its warranty period it

should be returned to the place of purchase for a free of charge replacement. ML Accessories does

not accept responsibility for any installation costs associated with the replacement product. Your

statutory rights are not affected. ML Accessories reserve the right to alter product speciﬁcation

without prior notice.

Knightsbridge HBLU1 User manual

Knightsbridge HBLU1 User manual

Knightsbridge HBLU1 User manual

Related papers

Other documents