2. Knightsbridge
  3. HBLU1

Knightsbridge HBLU1 User manual

  • Hello! I've reviewed the Installation & Maintenance Manual for the Knightsbridge HBLU series brackets. This manual provides clear instructions on how to install and maintain these brackets, including steps for mounting, securing the luminaire and important cleaning and warranty information. I'm ready to answer any questions you have regarding this document.
  • What type of cleaning should be used for this product?
    What is the warranty period for this product?
    What should I avoid when cleaning the product?
1
122
INSTALLATION & MAINTENANCE MANUAL
HBLU (bracket for HBL fittings)
2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
HBLU1 / HBLU2
GENERAL INSTRUCTIONS
INSTALLATION
Fig 1
Fig 2
• Using the bracket as a template, mark the location of the fixing holes, drill 2x 10mm holes ensuring
not to infringe with any joists, gas or water pipes or electrical cables
• Using a hammer, tap the expansion bolts into the 10mm fixing holes (see Fig 1)
• Tighten expansion bolt nuts but allow enough space for the bracket to mount
• Remove the driver housing via the 4 Allen screws (see Fig 2)
• Align the mounting bracket with 2 of the driver housing screw pillars (see Fig 3)
HBLseries
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:
HBL100/HBL150/HBL200/HBL240
SAFETY
• Installationofthisluminaireshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductseriesisClassIandrequiresanearth
• ThisproductseriesisIP65rated(recommendedindooruseonly)
• Thisproductisdimmableviaa1-10Vdimmer
INSTALLATION
Providepowertotherequiredpointofinstallation.SuitableIPratedjunctionsboxesshouldbeusedwhere
required
Suspensionmounting
Tosuspendthefitting,screwthemountinghoopintothetopoftheluminaire(seeFig1)
Fig1
Bracketmounting
Usingthebracketasatemplate,markthelocationofthefixingholes,drill2x10mmholesensuringnotto
infringewithanyjoists,gasorwaterpipesorelectricalcables
Usingahammer,taptheexpansionboltsintothe10mmfixingholes(seeFig2)
Fig2
Screwdown
mountinghoop
Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount
Removethedriverhousingviathe4Allenscrews(seeFig3)
Fig3
Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)
Fig4
PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown
the4Allenscrews(seeFig5)
Fig5
Removethe4Allenscrews
FastendownAllenscrews
3
Fig 3
Fig 4
Fig 5
• Position the driver housing into the bracket ensuring all Allen screw holes are correctly aligned and
fasten down the 4 Allen screws (see Fig 4)
• Lift the fitting up to the expansion bolts and slide into the bracket (see Fig 5)
• Tighten the 2 expansion bolts to secure the luminaire to the surface
Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount
Removethedriverhousingviathe4Allenscrews(seeFig3)
Fig3
Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)
Fig4
PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown
the4Allenscrews(seeFig5)
Fig5
Removethe4Allenscrews
FastendownAllenscrews
Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount
Removethedriverhousingviathe4Allenscrews(seeFig3)
Fig3
Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)
Fig4
PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown
the4Allenscrews(seeFig5)
Fig5
Removethe4Allenscrews
FastendownAllenscrews
Liftthefittinguptotheexpansionboltsandslideintothebracket(seeFig6)
Fig6
Tightenthe2expansionboltstosecuretheluminairetothesurface
Towiretheluminairewithoutadimmer(seefig7)
Fig7
Towiretheluminairewitha1-10Vdimmer(seeFig8)
Live-brown
Earth–green/yellow
Neutral-blue
Blue:Dim+
White:Dim-
Neutral-blue
Earth–green/yellow
Live-brown
4
ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk SBFEB17_V2
GENERAL
WARNING
WARRANTY
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the product.
Do not use any source of high pressure washers to maintain or clean this product.
Ensure correct fixtures are used for the surface that the product is fixed to.
This product has a warranty of 5 years from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period it
should be returned to the place of purchase for a free of charge replacement. ML Accessories does
not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
/