Altronix HUBWAYAVP Installation guide

HUBWAYAVP
Altronix
Brand
Altronix
Model
HUBWAYAVP
Category
Security camera accessories
Type
Installation guide

Altronix HUBWAYAVP is a video balun/combiner designed to work with the HubWayH16 Passive UTP Transceiver Hub, allowing you to route video and power from Altronix HubWay or HubSat units to fixed cameras. It features pass-through video/power, 75 Ohm video input, 1A supply current, and a low profile that fits inside dome cameras and back boxes. The HUBWAYAVP is easy to install, simply connect the RJ45 connectors to the HubWayH16 hub and the camera, and then connect the power output wires to the power input terminals of the camera.

Altronix HUBWAYAVP is a video balun/combiner designed to work with the HubWayH16 Passive UTP Transceiver Hub, allowing you to route video and power from Altronix HubWay or HubSat units to fixed cameras. It features pass-through video/power, 75 Ohm video input, 1A supply current, and a low profile that fits inside dome cameras and back boxes. The HUBWAYAVP is easy to install, simply connect the RJ45 connectors to the HubWayH16 hub and the camera, and then connect the power output wires to the power input terminals of the camera.

Overview:
HubWayAvP Video Balun/Combiner, to be used with HubWayH16 Passive UTP Transceiver Hub, routes Video
and Power from the Altronix HubWay or HubSat units for fixed cameras.
Fig. 1 - HubWayAvP
Power
Black
Red
Video
HubWayAvP passes AC voltage from pins 3, 4, 5, 6, 7, 8 to terminals marked [AC Power] (Fig. 2, pg. 1).
Specifications:
• Pass through video/power.
• 75 Ohm video input.
• 1A supply current (based on power supply rating).
• Low profile fits inside dome cameras and back boxes.
Installation Instructions:
1. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1] of the
Altronix HubWayH16 UTP Passive Transceiver Hub (refer to HubWayH16 UTP Passive Transceiver Hub
Installation Instructions). Plug the RJ45 connector at the opposite end of the structured cable into the RJ45
jack of the HubWayAvP Video Balun/Combiner installed at Camera 1.
Repeat this step for all cameras.
2. Connect the power output wires of the HubWayAvP to the power input terminals of the camera (Fig. 1, pg. 1).
4. Verify proper polarity before connecting to DC camera(s).
5. Connect the BNC connector of the HubWayAvP to the BNC video output of the camera (Fig. 1, pg. 1).
Fig. 2 - CAT-5 Structured Cable Wiring Color Codes
1
1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -]
3 - White/Green [AC 2]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [AC 1]
7 - White/Brown [AC 2]
8 - Brown [AC 1]
2345678
HubWayAvP
Video Balun/Combiner
Installation Guide
Typical Application Drawings:
Fig. 3
HubWayH16 UTP
Passive Transceiver Hub
Video/
Power
HubWayAvP
Video Balun
Combiner
Structured Cable
CHANNEL
Camera
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIHubwayAvP K19U MEMBER
  • Page 1 1
  • Page 2 2

Altronix HUBWAYAVP Installation guide

HUBWAYAVP
Altronix
Brand
Altronix
Model
HUBWAYAVP
Category
Security camera accessories
Type
Installation guide

Altronix HUBWAYAVP is a video balun/combiner designed to work with the HubWayH16 Passive UTP Transceiver Hub, allowing you to route video and power from Altronix HubWay or HubSat units to fixed cameras. It features pass-through video/power, 75 Ohm video input, 1A supply current, and a low profile that fits inside dome cameras and back boxes. The HUBWAYAVP is easy to install, simply connect the RJ45 connectors to the HubWayH16 hub and the camera, and then connect the power output wires to the power input terminals of the camera.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents