Barco MFGD 1218 User manual

Category
Software
Type
User manual

This manual is also suitable for

Installation & User Manual
System manual E1
Copyright notice
System manual E1 3
Copyright notice
This document is copyrighted. All rights are reserved. Nor this
document, nor any part of it, may be reproduced or copied in any
form or by any means - graphical, electronic, or mechanical
including photocopying, taping or information storage and
retrieval systems - without written permission of Barco
© 2004 Barco N.V. All rights reserved.
Copyright notice
4 System manual E1
(This page intentionally left blank.)
Table of Contents
System manual E1 5
Table of Contents
Preface........................................................................................ 7
Safety Instructions............................................................................. 11
Explanation of symbols ..................................................................... 14
Introduction ..............................................................................15
Overview............................................................................................ 17
BarcoMed Nio display controller overview............................... 17
Barco display overview.............................................................. 18
Parts, controls and connectors.......................................................... 19
Display controller installation .................................................. 21
Display controller installation ........................................................... 23
Display installation................................................................... 27
Precautions ........................................................................................ 29
Power connection.............................................................................. 30
Video connection............................................................................... 31
Wall mounting ................................................................................... 32
Display controller software installation ...................................35
Windows 2000 BarcoMed Nio software installation ....................... 37
Display controller tools.............................................................51
BarcoMed Driver Tab ......................................................................... 53
Introduction ................................................................................ 53
Using the BarcoMed Driver Tab ................................................. 53
Status .......................................................................................... 54
Palette Mode .............................................................................. 55
Drawing Modes .......................................................................... 57
Monitor Configuration ................................................................ 59
Configuring the Windows 2000 or Windows XP desktop......... 59
Configuring the DualView desktop............................................ 60
BarcoMed Hardware Tab ................................................................... 61
Table of Contents
6 System manual E1
Introduction ................................................................................ 61
Using The BarcoMed Hardware Tab........................................... 62
NioWatch................................................................................... 69
LCD sensor installation ...................................................................... 71
NioWatch operation........................................................................... 72
Display settings .......................................................................... 73
Test patterns............................................................................... 81
Application settings.................................................................... 82
Update NioWatch........................................................................ 84
Display operation...................................................................... 85
How to use the on-screen display (OSD)......................................... 87
Cleaning instructions ................................................................ 95
Precautions ........................................................................................ 97
Cabinet............................................................................................... 98
LCD panel ........................................................................................... 99
Troubleshooting......................................................................101
Pixel Faults................................................................................ 103
Windows 2000 display resolution ........................................... 103
Driver re-installation, updates or removal..................................... 107
Reinstalling or updating your BarcoMed Nio driver............... 107
Uninstalling the BarcoMed Nio driver or Barco NioWatch
software ..................................................................... 108
Appendices .............................................................................113
Appendix A: Possible resolutions ................................................... 115
Appendix B: Technical specifications.............................................. 117
Appendix C: Warranty Statement ................................................... 120
System manual E1 7
Preface
Preface
(This page intentionally left blank.)
8 System manual E1
(This page intentionally left blank.)
Preface
System manual E1 9
Notice
Although every attempt has been made to achieve technical
accuracy in this document, we assume no responsibility for errors
that may be found. Our goal is to provide you with the most
accurate and usable documentation possible; if you discover
errors, please let us know.
BarcoView software products are the property of BarcoView.
They are distributed under copyright by Barco N.V. or BarcoView,
LLC., for use only under the specific terms of a software license
agreement between Barco N.V. or BarcoView LLC. and the
licensee. No other use, duplication, or disclosure of a BarcoView
software product, in any form, is authorized.
The specifications of BarcoView products are subject to change
without notice.
Trademarks
All trademarks and registered trademarks are property of their
respective owners.
FCC notice
This equipment has been tested and found to comply with the
limits of a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
Preface
10 System manual E1
Canadian notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme
NMB-003 du Canada.
Disposal Information
The lamps inside the display contain mercury. Do not throw the
display in the trash. Dispose of it as required by local ordinances
or regulations.
Safety Instructions
System manual E1 11
Safety Instructions
General Recommendations
Read the safety and operating instructions before operating the
display.
Retain safety and operating instructions for future reference.
Adhere to all warnings on the display and in the operating
instructions manual.
Follow all instructions for operation and use.
Electrical shock
Type of protection (electrical):
Class I equipment
Degree of safety (flammable anesthetic mixture):
Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
Power connection
• Power requirements: The display must be powered using the
12 VDC power supply that is supplied with the display.
• The 12 VDC power supply must be powered by the AC mains
voltage.
Safety Instructions
12 System manual E1
•Power cords:
Power cord with CEE 7 plug: The colors of the mains
lead are colored in accordance with the following
code: Green-and-yellow: Earth (safety earth), Blue:
Neutral, Brown: Line
Power cord with ANSI 73.11 plug: The wires of the
power cord are colored in accordance with the
following code: Green/yellow: ground, White:
neutral, Black: line (live)
• Do not overload wall outlets and extension cords as this may
result in fire or electric shock.
• Mains lead protection (U.S.: Power cord): Power cords should
be routed so that they are not likely to be walked upon or
pinched by items placed upon or against them, paying
particular attention to cords at plugs and receptacles.
Water and moisture
Never expose the display to rain or moisture.
Never use the display near water - e.g. near a bathtub,
washbasin, swimming pool, kitchen sink, laundry tub or in a wet
basement.
Ventilation
Do not cover or block the ventilation openings in the cover of the
set. When installing the display in a cupboard or another closed
location, heed the necessary space between the set and the
sides of the cupboard.
Installation
Place the display on a flat, solid and stable surface that can bear
the weight of at least 3 displays. If you use an unstable cart or
stand, the display may fall, causing serious injury to a child or
adult, and serious damage to the equipment.
More warnings in the Installation chapter.
Safety Instructions
System manual E1 13
This apparatus conforms to:
CE, IEC 60950, UL 60950, CAN/CSA C22.2 No. 60950 (c-UL)
National Scandinavian Deviations for Cl. 1.7.2 :
Finland: "Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan"
Norway: "Apparatet må tilkoples jordet stikkontakt"
Sweden: "Apparaten skall anslutas till jordat uttag"
Explanation of symbols
14 System manual E1
Explanation of symbols
Symbols on the display and power supply
On the display or power supply, you may find the following
symbols:
Symbols used throughout the manual:
Indicates the display is approved according to
the CE regulations
or
Indicates the display is approved according to
the UL regulations
or
Indicates the display is approved according to
the c-UL regulations
Indicates the display is approved according to
the DEMKO regulations
Indicates the display is approved according to
the CCC regulations
Indicates the USB connectors on the display
Warning Caution
Important notice or
remark
Note
Hint, tip Additional
information
System manual E1 15
Introduction
Introduction
(This page intentionally left blank.)
16 System manual E1
(This page intentionally left blank.)
Overview
System manual E1 17
Overview
Thank you for choosing Barco.
BarcoMed Nio display controller overview
The BarcoMed Nio Display Controller delivers a quality image
with 256 simultaneous shades of gray for medical viewing
applications.
Minimum system requirements
• Pentium II 266 MHz with 128 MB RAM (Pentium II 800MHz
with 256 MB RAM for cineloops)
• PCI slot with no obstructions
• PCI 2.1 and/or 2.2 Compliant
•Windows
®
XP Professional Service Pack 1or Windows
®
2000
Professional Service Pack 4
Features of the BarcoMed Nio display controller
• Dual Head Configuration
• 8-bitin/10-bit out LUT
• 64MB Video Memory
• Landscape Mode
• 256 Simultaneous shades of gray
• Hardware cursor
• 64bit/66Mhz Single slot PCI Card
• Displays VGA boot messages on E1 displays.
Supported resolutions for each head of the BarcoMed Nio display
controller
For BarcoMed Nio 1MP
• 1280 x 1024 @ 60 HZ
Overview
18 System manual E1
For all BarcoMed Nio display controllers
The following resolution is also available when the OS is booted
in VGA mode.
• 640x480 @ Default Refresh Rate, 16 colors
System Configuration Guidelines
Because of the low power consumption and low heat generation
of the BarcoMed Nio display controller, multiple controllers may
be installed in adjacent PCI slots or adjacent to other PCI boards.
Additionally there should be no need to modify either the PC’s
power supply and/or cooling system.
Barco display overview
MFGD 1218 display
The MFGD 1218 is a 18.1-inch grayscale LCD display with a native
resolution of 1280 x 1024.
Its high-brightness, combined with image crispness and excellent
viewing angle, makes it an ideal solution for a multitude of
medical applications and environments.
Power saving
The display is equipped with a power saving system. When left
idle for a certain time, the computer connected to the display,
will power down the display.
The power saving system works with the standard Windows
power saving and with the DPMS function on the Barco BarcoMed
display controller (if installed in the PC).
Foot
The user can easily change the panel viewing angle, allowing to
use the display in the optimal viewing conditions.
Also, the display panel can be easily detached from the foot,
allowing to mount the panel to the wall.
Parts, controls and connectors
System manual E1 19
Parts, controls and connectors
Front
Figure 1
1. Menu key
2. Minus (<->) key, to scroll down in the on-screen display
(OSD) and decrease values.
3. Plus (<+>) key, to scroll up in the on-screen display (OSD)
and increase values.
4. Power LED
The LED is off when the display is off.
The LED is green when the display is on.
The LED is orange when the display is in Stand-by power-
saving mode.
5. Power key
BARCO
de
f
gc
Parts, controls and connectors
20 System manual E1
Rear
Figure 2
1. DC power input
Connect the external power supply, delivered with the
display, to this connector.
2. D-Sub 15 (VGA) video input (analog video)
3. DVI (digital) video input
4. S-Video input (analog video)
5. Push-button to release the panel from the foot
BARCO
defc
g
System manual E1 21
Display controller installation
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

Barco MFGD 1218 User manual

Category
Software
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI