Barco Coronis Color 2MP (MDCC-2121) User guide

Type
User guide
Getting Started Guide
Coronis
Supported displays:
MDCC 2121, MDCG 2121, MDCG 3120
(This page intentionally left blank.)
2
(This page intentionally left blank.)
3
Copyright notice
This document is copyrighted. All rights are reserved. Neither this
document, nor any part of it, may be reproduced or copied in any
form or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems -
without written permission of Barco
© 2013 Barco N.V. All rights reserved.
Notice
Although every attempt has been made to achieve technical accuracy
in this document, we assume no responsibility for errors that may be
found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.
Barco software products are the property of Barco. They are
distributed under copyright by Barco N.V. or Barco, Inc., for use only
under the specific terms of a software license agreement between
Barco N.V. or Barco Inc. and the licensee. No other use, duplication, or
disclosure of a Barco software product, in any form, is authorized.
The specifications of Barco products are subject to change without
notice.
Trademarks
All trademarks and registered trademarks are property of their
respective owners.
Patent information
This product is covered under the following intellectual property
rights:
US Patent RE43,707
US Patent 7,038,186
US Patent 7,166,829
US Patent 6,950,098
European Patent 1 274 066.
4
Indications for use
The Coronis displays are intended to be used in displaying and
viewing digital images for review and analysis by trained medical
practitioners.
The Coronis displays are not intended for primary diagnostic review of
Mammography images.
Table of Contents
5
Table of Contents
Preface..................................................................................... 7
Regulatory compliance information................................................ 8
FCC Compliance Information..................................................... 8
Canadian notice ........................................................................ 9
CE mark notice ............................................................................... 10
Environmental information ........................................................... 11
Safety Instructions ......................................................................... 14
EMC notice ...................................................................................... 17
Explanation of symbols.................................................................. 23
Recommendations for using your display system ....................... 25
Display controller installation ............................................... 27
Display Controller Installation ....................................................... 28
Which display controller? ....................................................... 28
Installing a Barco display controller....................................... 28
Installation Procedure............................................................. 31
Display installation................................................................ 37
Installation precautions ................................................................. 38
Display parts, controls and connectors ......................................... 39
Front ........................................................................................ 39
Rear ......................................................................................... 41
Connectors............................................................................... 41
Side.......................................................................................... 42
Foot.......................................................................................... 43
Single-head installation................................................................. 45
Dual-head installation ................................................................... 47
Vesa-mount installation ................................................................ 50
Adjust panel orientation................................................................ 51
Table of Contents
6
Connecting the signal cables......................................................... 52
Cable routing.................................................................................. 55
Cleaning instructions...................................................................... 58
Precautions.............................................................................. 58
Front glass............................................................................... 58
Cabinet .................................................................................... 59
Software installation ............................................................. 61
Driver and Software Installation ................................................... 62
Driver and software installation prerequisites...................... 62
Installing the B
ARCO MXRT drivers and software ................... 62
Installing the B
ARCOMED CORONIS or Nio drivers and software68
Where to get more information............................................75
Troubleshooting.....................................................................77
General tips.................................................................................... 78
Configuring Windows..................................................................... 79
Setting the resolution of your B
ARCO CORONIS Display............ 79
Setting the Color and Palette Modes..................................... 81
Configuring the Windows desktop......................................... 81
Technical Specifications......................................................... 83
Warranty Statement .............................................................. 93
Preface
7
Preface
Regulatory compliance information
8
Regulatory compliance information
FCC Compliance Information
CLASS B:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including
interference that may cause undesired operation.
The use of shielded cables for connection of the monitor to the
graphics card is required to ensure compliance with FCC regula-
tions. Changes or modifications to this unit not expressly
approved by Barco could void the user’s authority to operate this
equipment.
Regulatory compliance information
9
Canadian notice
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme à la norme NMB-001 du Canada.
CE mark notice
10
CE mark notice
Declaration of Conformity in accordance with Article 10 (1) of the CE directive
This product has been designed and manufactured in accordance with
the essential requirements of the Directives 2004/108/EC and
MDD 93/42/EEC (amended by 2007/47/EC (class II b product), and
for this product the procedures of Annex II have been applied to mark
the product with the CE label.
Environmental information
11
Environmental information
Disposal Information
This product consists of devices that may contain mercury, which must
be recycled or disposed of in accordance with local, state, or country
laws. (Within this system, the backlight lamps in the monitor display
contain mercury.)
This equipment has required the extraction and use of natural
resources for its production. It may contain hazardous substances for
health and environment.
In order to avoid the dissemination of those substances in the
environment and to diminish the pressure on natural resources, we
encourage you to use the appropriate take-back systems.
Those systems will reuse or recycle most of the materials of your end-
of-life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those
systems.
If you need more information on the collection, reuse and
recycling systems, please contact your local or regional waste
administrator.
You can also contact us for more information on the environmental
performances of our products.
Environmental information
12
Information for China ROHS compliance
Table of toxic and hazardous substances/elements and their content,
as required by China’s management methods for controlling pollution
by electronic information products
中国大陆 RoHS
根据中国大陆 电子信息产品污染控制管理办法 ( 也称为中国大陆
RoHS)以下部份列出了本产品中可能包含的有毒有害物质或元素的名称
和含量。
本表适用的产品
液晶显示器
有毒有害物质或元素
Toxic or hazardous Substances and Elements
Part Name Pb Hg Cd Cr6+ PBB PBDE
Metal parts O O O O O O
Plastic parts O O O O O O
PCB or PCBA O O O O O O
LCD panel X X O O O O
Power supply/adapter X O O O O O
Power cable X O O O O O
Connectors and cables O O O O O O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006
Environmental information
13
LCD Monitor         
零部件名稱 有毒有害物質或元素
 铅Pb
(Hg)
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
金属机构件 O O O O O O
塑料机构件 O O O O O O
电路板组件 * O O O O O O
液晶面板 X X O O O O
电源模块 / 适配器 X O O O O O
电源线 X O O O O O
外部信号连接线 O O O O O O
*: 电路板组件包括印刷电路板及其构成的零部件,如电阻、电容、集成电路
、连接器等
○:表示该有毒有害物质在该部件所有均质材料中的含量均在 《电子信息产品中有
毒有害物质的限量要求标准》规定的限量要求以下
×:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 《电子信息产品中
有毒有害物质的限量要求标准》规定的限量要求;
但是上表中打 “×” 的部件,其含量超出是因为目前业界还没有成熟的可替代的技术
Safety Instructions
14
Safety Instructions
General Recommendations
Read the safety and operating instructions before operating the
display.
Retain safety and operating instructions for future reference.
Adhere to all warnings on the display and in the operating
instructions manual.
Follow all instructions for operation and use.
Electrical shock
WARNING: To avoid the risk of electric shock, this equipment must
only be connected to a supply mains with protective earth.
WARNING: Do not modify this equipment without authorization of the
manufacturer.
Type of protection (electrical):
Display with external power supply: Class I equipment
Degree of safety (flammable anesthetic mixture):
Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
Non-patient care equipment
Equipment primarily for use in a health care facility that is intended
for use where contact with a patient is unlikely.
Safety Instructions
15
Power connection - display with external power supply
Power requirements: The display must be powered using the
delivered medical approved 12 VDC power supply.
The medical approved DC power supply must be powered by
the AC mains voltage.
Power cords:
Utilize a UL-listed detachable power cord, 3-wire, type SJ or
equivalent, 18 AWG min., rated 300 V min., provided with a
hospital-grade type plug 5-15P configuration for 120V
application, or 6-15P for 240V application.
Do not overload wall outlets and extension cords as this may
result in fire or electric shock.
Mains lead protection (U.S.: Power cord): Power cords should
be routed so that they are not likely to be walked upon or
pinched by items placed upon or against them, paying
particular attention to cords at plugs and receptacles.
Transient over-voltage
If the equipment is not used for a long time, disconnect it from the AC
inlet to avoid damage by transient over-voltage.
To fully disengage the power to the unit, please disconnect the power
cord from the AC inlet.
Water and moisture
Never expose the display to rain or moisture.
Never use the display near water - e.g. near a bathtub, washbasin,
swimming pool, kitchen sink, laundry tub or in a wet basement.
Ventilation
Do not cover or block the ventilation openings in the cover of the set.
When installing the display in a cupboard or another closed location,
heed the necessary space between the set and the sides of the
cupboard.
Safety Instructions
16
Installation
Place the display on a flat, solid and stable surface that can support
the weight of at least 3 displays. If you use an unstable cart or stand,
the display may fall, causing serious injury to a child or adult, and
serious damage to the equipment.
More warnings in the Installation chapter.
This apparatus conforms to:
IEC 60950-1:2005, IEC 60601-1:1988 + A1:1991 + A2:1995, IEC 60601-
1:2005, IEC 60601-1-2:2007, UL 60950-1, 1st edition, 2007, UL 60601-
1, 1st edition - 2006,ANSI/AAMI ES 60601-1:2006,CSA C22.2 No.
60950-1-03, 1st edition, 2006, CAN/CSA-C22.2 No. 601.1-M90, 2005,
CAN/CSA-C22.2 No. 60601-1, 2008, CE - 2004/108/EC, CE - 93/42/
EEC + 2007/47/EC, Class IIb, CE - 2011/65/EC, EN 60601-1-2:2007,
RoHs, Demko - EN 60601-1:1990 + A1:1993 + A2:1995,Demko - EN
60601-1:2006, CCC - GB9254-2008, CCC - GB4943.1-2011, CCC -
GB17625.1-2003, KCC (MDCG 2121), FCC class B, ICES-001 level B,VCCI,
FDA 510(k)
National Scandinavian Deviations for Cl. 1.7.2 :
Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun
pistorasiaan"
Norway: "Apparatet må tilkoples jordet stikkontakt"
Sweden: "Apparaten skall anslutas till jordat uttag"
EMC notice
17
EMC notice
No specific requirement on the use of external cables or other
accessories except power supply.
With the installation of the device, use only the delivered power
supply or a spare part provided by the legal manufacturer. Using
another can result in a decrease of the immunity level of the device.
Electromagnetic emissions
The B
ARCO CORONIS Display is intended for use in the electromagnetic
environment specified below.
The customer or the user of the B
ARCO CORONIS Display should assure
that it is used in such an environment.
This B
ARCO CORONIS Display complies with appropriate medical EMC
standards on emissions to, and interference from surrounding
equipment. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device
Emissions test Compliance Electromagnetic environment – guidance
RF emissions
CISPR 11
Group 1 The B
ARCO CORONIS Display uses RF energy
only for its internal function. Therefore, its
RF emissions are very low and are not likely
to cause any interference in nearby
electronic equipment
RF emissions
CISPR 11
Class B
The BARCO CORONIS Display is suitable for use
in all establishments, including domestic
establishments and those directly
connected to the public low-voltage power
supply network that supplies buildings used
for domestic purposes.
Harmonic emissions
IEC 61000-3-2
Class D
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Complies
EMC notice
18
must accept any interference received, including interference that
may cause undesired operation.
Interference can be determined by turning the equipment off and on.
If this equipment does cause harmful interference to, or suffer from
harmful interference of, surrounding equipment, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna or equipment.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced technician for help
Electromagnetic immunity
The B
ARCO CORONIS Display is intended for use in the electromagnetic
environment specified below. The customer or the user of the B
ARCO
C
ORONIS Display should assure that it is used in such an environment.
Immunity test IEC 60601
Test levels
Compliance level Electromagnetic
environment – guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
± 6kV contact
± 8kV air
± 6kV contact
± 8kV air
Floors should be wood,
concrete or ceramic tile.
If floors are covered with
synthetic material, the
relative humidity should
be at least 30%
Electrical fast
transient/burst
IEC 61000-4-4
± 2kV for power
supply lines
± 1kV for input/
output lines
± 2kV for power
supply lines
± 1kV for input/
output lines
Mains power quality
should be that of a
typical commercial or
hospital environment
Surge
IEC61000-4-5
± 1 kV line(s) to
line(s)
± 2 kV line(s) to
earth
± 1 kV line(s) to
line(s)
± 2 kV line(s) to
earth
Mains power quality
should be that of a
typical commercial or
hospital environment
EMC notice
19
U
T
is the a.c. mains voltage prior to application of the test level
Voltage dips,
short
interruptions
and voltage
variations on
power supply
input lines
IEC 61000-4-11
< 5% U
T
(> 95%
dip in U
T
) for 0.5
cycle
40% U
T
(60%
dip in U
T
) for 5
cycles
70% U
T
(30%
dip in U
T
) for 25
cycles
< 5% U
T
(>95%
dip in U
T
) for 5s
< 5% U
T
(> 95%
dip in U
T
) for 0.5
cycle
40% U
T
(60% dip
in U
T
) for 5 cycles
70% U
T
(30% dip
in U
T
) for 25
cycles
< 5% U
T
(>95%
dip in U
T
) for 5s
Mains power quality
should by that of a
typical commercial or
hospital environment. If
the user of the B
ARCO
C
ORONIS Display requires
continued operation
during power mains
interruptions, it is
recommended that the
B
ARCO CORONIS Display be
powered from an
uninterruptible power
supply or a battery.
EMC notice
20
a Field strengths from fixed transmitters, such as base stations for radio (cellu-
lar/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF trans-
mitters, an electromagnetic site survey should be considered. If the mea-
Immunity
test
IEC 60601
test level
Level Electromagnetic environment –
guidance
Power
frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
3 A/m
Not
applic
able
Power frequency magnetic fields should be
at levels characteristic of a typical location
in a typical commercial or hospital
environment.
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 kHz to
80 MHz
3 V/m
80 MHz to
2.5 GHz
3 V
3 V/
m
Portable and mobile RF communications
equipment should be used no closer to any
part of the B
ARCO CORONIS Display, including
cables, than the recommended separation
distance calculated from the equation
applicable to the frequency of the
transmitter.
Recommended separation distance
80 MHz to 800 MHz
800 MHz to 2.5 GHz
Where P is the maximum output power
rating of the transmitter in watts (W)
according to the transmitter manufacturer
and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters,
as determined by an electromagnetic site
survey,
a
should be less than the
compliance level in each frequency range.
b
Interference may occur in the vicinity of
equipment marked with symbol:
P2.1d
P2.1d
P3.2d
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100

Barco Coronis Color 2MP (MDCC-2121) User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI