Garmin Toyota Quest 2 User manual

Owner’s Manual

pocket-sized navigator

Quest

®

2

Garmin International, Inc.

1200 East 151

st

Street,

Olathe, Kansas 66062, U.S.A.

Garmin (Europe) Ltd.

Unit 5, The Quadrangle, Abbey Park Industrial

Estate, Romsey, SO51 9DL, U.K.

Garmin Corporation

No. 68, Jangshu 2

nd

Road, Shijr,

Taipei County, Taiwan

in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of

this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that

such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial

distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content

without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current updates and

supplemental information concerning the use and operation of this and other Garmin products.

Garmin

®

, AutoLocate

®

, TracBack

®

, and MapSource

®

are registered trademarks, and Quest

™

is a trademark of Garmin Ltd. or its subsidiaries and

may not be used without the express permission of Garmin.

September 2006 Part Number 190-00675-00 Rev. A Printed in Taiwan

Quest

®

2 Owner’s Manual i

IntroductIon

Thank you for purchasing Toyota’s portable navigation Quest

™

2

by Garmin. To get the most out of your new navigation system, go

through this owner’s manual and learn the operating procedures for

your unit.

Introduction: contains the Table of Contents and Safety

Information.

Getting Started: provides information to help get you started. If

you have never navigated with a GPS unit, try the “Tutorial”

on page 2.

Basic Operation: teaches you how to use your Quest 2 to nd

items, create routes, and initiate a TracBack

®

.

Using the Main Pages: describes the Map page and other main

pages of your Quest 2.

Customizing Your Quest 2: explains how to change settings to

meet your specic needs.

Understanding GPS: describes the basics of GPS navigation and

the features on the GPS Information page.

Appendix: contains tips and shortcuts, information about care and

Safe Mode, specications, and regulatory information.

Index: provides key words to help you nd information.

Manual Conventions

This manual uses the term “select” when you need to choose an

icon, button, or tab. To select something, use the Rocker to move

the cursor (or highlighted area) to the position. To activate the

selection, press the OK key.

This manual uses the term WARNING to indicate a

potentially hazardous situation, which, if not avoided, could

result in death or serious injury.

This manual uses the term CAUTION to indicate a

potentially hazardous situation, which, if not avoided, may

result in minor injury or property damage. The term may

also be used without the symbol to alert you to avoid unsafe

practices.

IntroductIon

ii Quest

®

2 Owner’s Manual

IntroductIon > table of contents

table of contents

Introduction ...........................................................................i

Warning .....................................................................................iii

Caution ......................................................................................iv

Getting Started .....................................................................1

Introducing the Quest 2 ............................................................. 1

Tutorial ....................................................................................... 2

Vehicle Installation ..................................................................... 4

Turning the Quest 2 On and Off ................................................ 5

Using the Keys .......................................................................... 6

Basic Operation ...................................................................8

Finding Places and Routing to Them ....................................... 8

My Locations ........................................................................... 14

Setting Your Home Location .................................................... 18

Using TracBack ....................................................................... 19

Planning and Modifying Routes .............................................. 21

Using the Main Pages .......................................................27

Map Page ................................................................................ 27

Next Turn Page ....................................................................... 30

Current Route Page ................................................................ 31

Trip Information Page .............................................................. 32

Customizing Your Quest 2 ...............................................33

Customizing the Map Page ..................................................... 33

Customizing the Display .......................................................... 35

Customizing the Overall System Setup

................................... 36

Customizing the Route Settings .............................................. 37

Customizing the Units Settings ............................................... 38

Changing the Time Settings .................................................... 38

Changing the Track Setup ....................................................... 39

Customizing the Welcome Page ............................................. 40

Viewing Software and Unit Information ................................... 40

Understanding GPS ...........................................................41

The GPS Information Page ..................................................... 41

Appendix ............................................................................45

Quest 2 Shortcuts .................................................................... 45

Data Fields .............................................................................. 45

Adding Maps to Your Quest 2 .................................................. 47

Caring for the Quest 2 ............................................................. 49

Safe Mode ............................................................................... 49

Specications .......................................................................... 50

Product and Regulatory Information ........................................ 51

Toyota Limited Warranty .......................................................... 52

Index ...................................................................................53

Quest

®

2 Owner’s Manual iii

IntroductIon > safety InformatIon

Failure to avoid the following potentially hazardous situations could

result in an accident or collision resulting in death or serious injury.

Always operate the vehicle in a safe manner. Do not become distracted

by the Quest 2 while driving, and always be fully aware of all driving

conditions. Minimize the amount of time spent viewing the screen of the

Quest 2 while driving and use voice prompts when possible. Do not enter

destinations, change settings, or access any functions requiring prolonged

use of the unit’s controls while driving. Pull over in a safe and legal

manner before attempting such operations.

When navigating, carefully compare information displayed on the Quest 2

to all available navigation sources, including information from street signs,

visual sightings, and maps. For safety, always resolve any discrepancies or

questions before continuing navigation.

The Quest 2 contains a non-user-replaceable, rechargeable lithium-

ion battery. The battery may present a risk of re or chemical burn if

mistreated.

• Do not remove from the unit, heat unit above 140°F (60°C), or

incinerate.

• Dispose of unit properly. Contact your local waste disposal

department for information on properly disposing of lithium-ion

batteries.

Warning

WARNING: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive

harm. This Notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer

to our Web site at www.garmin.com/prop65.

iv Quest

®

2 Owner’s Manual

IntroductIon > safety InformatIon

Failure to avoid the following potentially hazardous situations may

result in injury or property damage.

The Quest 2 is designed to provide you with route suggestions. It does

not reﬂect road closures or road conditions, trafc congestion, weather

conditions, or other factors that may affect safety or timing while driving.

Use the Quest 2 only as a navigational aid. Do not attempt to use the Quest

2 for any purpose requiring precise measurement of direction, distance,

location, or topography. This product should not be used to determine

ground proximity for aircraft navigation.

The Global Positioning System (GPS) is operated by the United States

government, which is solely responsible for its accuracy and maintenance.

The government’s system is subject to changes which could affect the

accuracy and performance of all GPS equipment, including the Quest 2.

Although the Quest 2 is a precision navigation device, any navigation

device can be misused or misinterpreted and, therefore, become unsafe.

Map Data Information: One of the goals of Garmin is to provide customers with the most complete and accurate cartography that is available to us at a

reasonable cost. We use a combination of governmental and private data sources, which we identify in product literature and copyright messages displayed to the

consumer. Virtually all data sources contain inaccurate or incomplete data to some extent. In some countries, complete and accurate map information is either not

available or is prohibitively expensive.

NOTICE TO DRIVERS IN CALIFORNIA AND MINNESOTA

: State law prohibits drivers in California and Minnesota from using suction mounts on their

windshields while operating motor vehicles. Other Garmin dashboard or friction mounting options should be used. Garmin does not take any responsibility for

any nes, penalties, or damages that may be incurred as a result of disregarding this notice. (See California Vehicle Code Section 26708(a); Minnesota Statutes

2005, Section 169.71.)

Caution

Quest

®

2 Owner’s Manual 1

GettInG started > IntroducInG the Quest 2

GettInG started

Introducing the Quest 2

Power/Speaker connector

External antenna

connector

Back View

USB connector

Power key

Flip-up GPS antenna

(Position the antenna parallel to

the surface of the road.)

Keypad

256-Color high-resolution TFT display

Front View

2 Quest

®

2 Owner’s Manual

GettInG started > tutorIal

Tutorial

This tutorial guides you through the steps for nding a restaurant in

your area and then creating a route to it. If you have never used a

GPS unit, try this simple task. You will see that using your Quest 2

is fast and easy.

Be sure the antenna is unobstructed as it looks for satellites. For

example, it cannot establish a satellite x if your vehicle is parked

in a garage. Position the antenna so that it is parallel to the

surface of the road so that it can have the best view of the sky.

Step 1: If you have not already done so, ﬂip up the antenna and

snap the Quest 2 into the vehicle mount. See page 4 for additional

instructions. Turn on the Quest 2, if necessary, and acknowlege the

warning message. When the unit has established a satellite x, it

shows a “Ready to Navigate” message.

Map page

Step 2: Press the FIND key. The Find Menu appears. Highlight the

Food & Drink icon located in the Find Menu and press the

OK key.

FIND key

Rocker

OK key

Step 3: A list of restaurants in your area appears on a page similar

to the one shown below. Use the Rocker to highlight a restaurant

in the list. Then press the OK key.

Use the Rocker to

highlight a restaurant.

Quest

®

2 Owner’s Manual 3

GettInG started > tutorIal

Step 4: Information about the restaurant appears on a page similar

to the one shown below. To create a route to this restaurant,

highlight the Route To button located at the bottom of the page.

Then press OK.

Select Route To to

create a route to this

restaurant.

The Quest 2 calculates the route and provides directions. Follow

the purple line on the Map page to your destination.

4 Quest

®

2 Owner’s Manual

GettInG started > VehIcle InstallatIon

Vehicle Installation

You can install and store the Quest 2 in the vehicle mount. The

Quest 2 runs off power from your vehicle when the ignition is

turned on. Be sure the vehicle ignition is turned off before you

install or remove the unit from the mount.

To install the Quest 2 in the mount:

1. Flip up the GPS antenna to a 90° angle on the back of the

Quest 2.

2. Insert the bottom of the Quest 2 into the bottom of the

mount, as shown. The antenna ts through the opening in

the back of the mount.

3. Snap the Quest 2 back into the mount so that it is fully

seated.

Tab

To remove the Quest 2, push the tab

up and pull the Quest 2 forward.

NOTE: Make sure the tabs are located and locked correctly.

To remove and store the Quest 2:

1. Push the tab up that holds the Quest 2 in place (see above).

2. Pull the Quest 2 forward and then out of the mount.

Quest

®

2 Owner’s Manual 5

GettInG started > turnInG the Quest 2 on and off

Turning the Quest 2 On and Off

Press and hold the Power key on the front of the unit to turn

it on or off. When turned on, the Welcome page appears brieﬂy,

followed by a Safe Driving Warning Message. Press the OK key

to acknowledge the message. Your Quest 2 automatically starts

searching for satellite signals to nd your current location. The rst

time the Quest 2 acquires satellites it may take several minutes.

Afterward, acquisition times are quicker during normal use.

NOTE: If the unit prompts you to enter a security code, contact

your Toyota dealer.

If your unit is in the vehicle mount, it turns on automatically when

you start your vehicle. When you turn off your vehicle, the External

Power Lost message appears. Press any key to switch the unit to

battery power. Otherwise, the Quest 2 turns off after 30 seconds.

Turning Off Satellite Reception for Indoor Use

You can set your Quest 2 to indoor use, which stops satellite

reception and conserves battery power. Thoroughly familiarize

yourself with the routing features of the Quest 2 by

simulating routes.

To turn off satellite reception:

1. Press the Page key to open the Map page.

2. Press the MENU key.

3. Highlight Use Indoors and press OK. GPS is disabled.

To turn on satellite reception:

1. Press the Page key to open the Map page.

2. Press the MENU key.

3. Highlight Acquire Satellites and press OK. GPS is

enabled, and your Quest 2 begins to acquire satellite

signals.

6 Quest

®

2 Owner’s Manual

GettInG started > usInG the Keys

Using the Keys

Use the keys to perform specic tasks such as nding places or planning routes. With the exception of the Power key, press and quickly

release a key to perform its function. If a key has a secondary function, press and hold the key to activate it.

Power—press and hold to turn the unit on or off.

Press once to adjust the illumination of your screen.

When the illumination window appears, use the

Rocker to move the slider to the left or right to dim

or brighten your backlight. Press OK.

Page—press to open pages. Press Page to

close the current window or menu and return to the

previous page. When you are entering data, press

Page to cancel the data entry and restore the

previous value.

Rocker—press to highlight options or move the

map pointer in any direction.

OK—press to select items. Press OK to view

information pages when panning the Map page. To

save your current location in My Locations, press

and hold OK.

FIND

—press to search for cities, addresses, and

other points of interest. Press FIND twice to open

the Recent Finds menu. Press and hold FIND to

“Route Home” (see page 18).

MENU

—press to show a menu of options for

the current page. Press MENU twice to open the

Settings menu. Press and hold MENU to open the

Route Options menu.

OUT

—zooms out on the Map page. Also scrolls

down a list.

Speak—triggers your unit’s “voice” to repeat the next

turn or current destination when you are navigating a

route. Press and hold to adjust the volume. The unit

must be in the vehicle mount to hear audio commands.

IN—zooms in on the Map page. Also scrolls up

a list.

Quest

®

2 Owner’s Manual 7

GettInG started > usInG the Keys

Selecting Options and Entering Data

Use the OK key and the Rocker to select options and activate your

selections.

To select and activate an option or on-screen button:

1. Use the Rocker to move up, down, right, or left to the

selection or on-screen button.

2. Press OK to activate the feature.

To exit a menu or return to the previous setting:

Press Page . The Page key moves backward through

your steps or menus.

Using the On-screenOn-screen Keyboard

The on-screen keyboard opens when you need to enter data, such

an address or a city. The on-screen keyboard is used in a variety of

places throughout the Quest 2. Its appearance may alter, depending

on your purpose for using it, but it always functions the same way.

Return key

The up arrow changes the

capital letters to lower case

and numbers to symbols.

Use the Rocker to select a letter, number, or symbol, and then

press OK. To create spaces, select the blank space between the Y

and Z. Use the Clear (Back) box to delete letters/numbers. The ◄

and ► keys are backspace and forwardspace keys. The up arrow

changes the capital letters to lower case and the numbers to

symbols. Use the Return key to create a new line. When you

have entered all text, select Done.

8 Quest

®

2 Owner’s Manual

basIc operatIon > fIndInG places and routInG to them

basIc operatIon

Finding Places and Routing to Them

Use the Find Menu to locate and create routes to cities, addresses,

parks, restaurants, or hotels.

Find Menu

Press the Rocker down to see more Find categories.

To nd a place and route to it:

1. Press the FIND key. The Find Menu appears.

2. Highlight a category

to help you nd your

destination, such as Food

& Drink, Lodging, or All

Points of Interest. Press

OK. A list of places near

your current location

appears.

3. Highlight the place and

press OK. An information

page appears.

4. Highlight Route To and

press OK. The Quest 2

calculates your route.

Find Menu Results List

Information Page

Quest

®

2 Owner’s Manual 9

basIc operatIon > fIndInG places and routInG to them

Advanced Search Methods and Tips

The search results list can be quite long. Use the following tips to

narrow your search.

Entering Containing Letters

If you know the name of the place you are searching for, select

the <Containing> box. Use the

on-screen keyboard to enter letters

contained in the name. The more

fully you type the name, the more

accurate your search results. For

example, typing “SU” in order to

nd Sun’s Deli returns names such

as Subway and Tropik Sun.

Searching Sub-Categories

If you would like to search for a

type of food (such as Chinese, Deli,

International, Fast Food), highlight

the All Categories box and press

OK. Highlight a food category

(sub-category) and press OK. A new

list appears ltered with the selected

category.

Panning and Finding

You can nd places that are beyond your current location by

panning to a particular area on the map. Open the Map page

and pan the map to the location. Press the FIND key, and the

unit searches for places near the map pointer. See page 28 for

information about panning the map.

Finding Places Near this Place

After you have found a place, open the item’s information page.

To nd another place (such as a hotel or restaurant) near this place,

highlight Find Near and press OK.

Saving this Place to My Locations

After you have found a place, open the item’s information page.

Highlight Save and press OK to save this place to My Locations.

Using the Information Page Menu

After you have found a place, open the item’s information page and

press the MENU key to reveal more options.

To see where this item is located on the map, select Show Map.

For step-by-step directions from the place to your current location,

select Directions to Me. Select Find Near Current Route to list

all places along your current route.

Using the Containing Field

Using Sub-Categories

10 Quest

®

2 Owner’s Manual

basIc operatIon > fIndInG places and routInG to them

Finding an Address or Intersection

To search for an address or intersection, select Addresses or

Intersections from the Find Menu. In both cases, a search wizard

appears that allows you to enter street information.

To nd an address or intersection:

1. Press FIND, highlight Addresses or Intersections, and

press OK.

2. Highlight a state and press OK.

3. Highlight Search All Cities and press OK.

4. Enter the address number and street using the on-screen

keyboard. For intersections, you only need to enter street

names.

5. A list of addresses or intersections appears. Highlight the

place you are looking for and press OK.

6. To create a route to this address, highlight Route To and

press OK.

Quest

®

2 Owner’s Manual 11

basIc operatIon > fIndInG places and routInG to them

Finding a City

To search for a city, select Cities from the Find Menu. A list of 50

cities near your current location appears.

To nd a city:

1. Press FIND, highlight Cities, and press OK. A list of cities

appears. Use the Rocker to move down the list.

2. Highlight the <Containing> box and press OK to narrow

your results or nd a city not on the list. Enter the name of

the city you are searching for using the on-screen keyboard.

3. Highlight a city and press OK. An information page appears.

4. To go to the city, highlight Route To and press OK.

Finding an Exit

Select Exits from the Find Menu to locate exits on highways,

freeways, and interstates.

To nd an exit:

1. Press the FIND key, highlight Exits, and press OK. All exits

on the highway or interstate that is closest to your current

location are listed.

2. To search for a particular road exit, press MENU, highlight

Select Exit Road, and press OK. Enter the name of the

road using the on-screen keyboard.

3. If you know you want to stop at an exit that has a particular

type of service, such as a gas station or rest area, select the

All Categories box and press OK. Then select a category

from the list.

4. Use the Rocker to highlight an exit from the search results

list and press OK. An information page for that exit appears.

Services at this exit appear on the exit’s information page.

Highlight the service you want to visit and press OK to view

information about it.

5. To go to the exit, highlight Route To and press OK.

12 Quest

®

2 Owner’s Manual

basIc operatIon > fIndInG places and routInG to them

Finding Recently-Found Places

Your Quest 2 stores the 50 places you have found most recently.

The most recently-reviewed item is at the top of the list.

To nd a recently-found place:

1. Press FIND, highlight Recent Finds, and press OK. A list of

recently-found items appears.

2. To narrow your search,

highlight All Categories and

press OK.

3. Highlight a category from the

list and press OK. The 15

most recent nds from the

category appear.

4. Highlight a place and press

OK.

5. To create a route to this

place, highlight Route To

and press OK.

The Quest 2 only stores places that you actually view. For example,

suppose you search for a restaurant by name and ve names appear.

If you view information on two of them, then these two restaurants

are stored in your Recent Finds list.

Deleting Recently-Found Places

If you want to delete a place from the Recent Finds list, highlight

the place’s name and highlight the red . Press OK, and the name

is removed from the list.

To remove all names in the Recent Finds list, press MENU while

on the Recent Finds page. Highlight Remove All and press OK.

NOTE: Deleting an item from the Recent Finds list only

removes the item from this list. It does not delete the actual city

from the Map page, your nd database, or My Locations.

Quest

®

2 Owner’s Manual 13

basIc operatIon > fIndInG places and routInG to them

Planning a Trip

If you are planning a trip and would like to nd vacation spots

ahead of time, consider using the “chain nd” method described

below. You can also follow these instructions for nding places

while you are already on a trip.

1. Find the city you plan to visit. See page 11 for more

instructions. In our example, Overland Park, KS is chosen.

2. Highlight Find Near and

press OK.

3. Select Lodging to look for

a place to stay in Overland

Park.

4. Your Quest 2 returns the

names of places to stay.

Highlight a place to stay and

press OK. In our example,

Bed and Breakfast Kansas

City is the lodging place.

5. From the Bed and Breakfast

information page, highlight

Find Near and press OK.

Then highlight Food & Drink and press OK.

6. A list of all eating establishments near Bed and Breakfast

Kansas City appears. Highlight a restaurant and press

OK.

7. To save the restaurant to your My Locations list, highlight

Save from the information page.

Restaurants near your lodging choice in Overland Park

You can also nd entertainment, services, and a variety of other

places near your chosen lodging area in the city of your choice.

When you are ready to take your trip, simply nd these places in

your Recent Finds or My Locations list. For more information on

trip planning, see “Planning and Modifying Routes” on page 21.

14 Quest

®

2 Owner’s Manual

basIc operatIon > my locatIons

My Locations

You can save your favorite places to the My Locations category of

the Find Menu. This allows you to easily nd your favorite places

later. For example, if you have found a great campsite, you can

save the place to My Locations. Then when you want to return to

the campsite, you can quickly nd and route to it.

Saving Your Favorite Places in “Favorite Places in “My Locations”

You can save up to 500 locations using four basic methods.

• Save an item you have found using the Find Menu.

• Save your present location from the Where Am I? page.

• Save a new location from the map using the

Rocker.

• Enter a new location’s position coordinates manually.

Saving an Item from the Find Menu

As discussed in the previous sections, you can save items you have

found using the Find Menu.

To save a place from the Find Menu:

1. Press FIND. Highlight the search category and press OK.

2. Highlight the place you want to save and press OK.

3. From the information page, highlight Save and press OK.

Where Am I?

Use the Where Am I? feature to nd out where you are and save

your location. This is particularly useful if you are traveling off

road or any place where street signs or navigational markers are not

available.

You must have a valid position (2D or 3D) x to mark your present

location. You can determine the satellite x by looking at the GPS

page. For more information, see “Understanding GPS” on page 41.

To nd out where you are and save your location:

1. Press the FIND key, highlight Where Am I?, and press OK.

Or, press and hold the OK key.

2. A Where Am I? page

appears, listing your current

location and the nearest

major intersections, if

available. Highlight Save

and press OK to save yoursave your

location to My Locations.

Page is loading ...

Garmin Toyota Quest 2 User manual

This manual is also suitable for

Garmin Toyota Quest 2 User manual

Related papers

Other documents