Mitsubishi VS-45607 User manual

MITSUBISHI

THE BIG SCREEN COMPANY TM

RISKOF ELECTRICSHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK).

NO USER-SERVlCEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

/_The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert

the user to the presence of uninsulated"dangerous voltage within the products enclosure

that may be of sufficient magnitude to constitute a risk of electric shock

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

Warning: To avoid permanently imprinting a fixed imageonto your TV screen,pleasedo not displaythe same

stationary imageson the screen for more than 15%of your total TV viewing in one week. Examplesof stationary

imagesare letterbox top/bottom barsfrom DVD disc or other video sources,side bars when showing standardTV

pictures on widescreenTV's,stock market reports, video game patterns, station logs,web sitesor stationary com-

puter images. Suchpatterns can unevenly agethe picture tubes causing permanent damageto theTV. Pleasesee page

58 for a detailed explanation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or reJocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate

this equipment.

WARNING:

TO REDUCE THE RISKOF FIREOR ELECTRIC SHOCK, DO NOT EXPOSETHISAPPLIANCE TO RAIN OR

MOISTURE.

CAUTION:

TO PREVENTELECTRICSHOCK, MATCH WIDE BLADE OF PLUGTO WIDE SLOT,FULLYINSERT.

NOTE TO CATV SYSTEM INSTALLER:

THIS REMINDER ISPROVIDEDTO CALLTHE CATV SYSTEMINSTALLER'SATTENTION TOARTICLE 820-40 OF

THE NEC THAT PROVIDESGUIDELINES FOR PROPERGROUNDING AND, IN PARTICULAR,SPECIFIESTHAT

THE CABLE GROUND SHALL BECONNECTEDTOTHE GROUNDING SYSTEMOFTHE BUILDING,AS CLOSE

TOTHE POINT OF CABLE ENTRYAS PRACTICAL.

Contents

Important Safeguards 5

Instructions on safety and proper handlingof your Mitsubishi television

Special Features 7

Distinctive features, items included with your Mitsubishi television and hookup guidelines

Shortcuts 8

A quick reference list

Connections 9

Basichookups to an antenna, cable and components

Remote Control Functions 15

Features of the remote control, programming to work with other audio and video products,

explanation of buttons

Thel_ ®Menu System 2 I

Explanation of the on-screen menu system and the basic set-up menu screens including

Memorizing Channels, Set Clock and Day, AV Connection and On-Screen Language

Remote Control Input and Channel Selection 3 I

Changing inputs and channels and setting the sleep timer with the remote control

The Main Menu Screens 33

Explains the Parent Lock, Channel Edit, Advanced Features and AudioNideo Settings Menus

Special Remote Control Functions 49

How the remote works with other products includingthe Mitsubishi A/V Network, viewing

the PIP (Picture-in-Picture) and POP (Picture-outside-Picture)

Control Panel Functions 54

Explanation of the front panel buttons and the back panel terminals

Troubleshooting 57

Common problems, notes on caring and cleaningyour Mitsubishi television and how to

obtain service

Appendices 6 I

Diamond ShieldTM installation, remote control programming codes, bypassing the parent lock

Please read all these instructions regarding your television set and retain for future refer-

ence. Follow all warnings and instructions marked on the television.

I. Read, Retain and Follow Instructions

Read all safety and operating instructions before operating the appliance. Retain the safety and operating

instructions for future reference. Follow all operating and use instructions.

2. Heed Warnings

Adhere to all warnings on the applianceand in the operating instructions.

3. Cleaning

Unplug thisTV receiver from the walt outlet before cleaning.Do not useliquid or aerosol cleaners.Cleaners

canpermanently damagethe cabinet or screen.Use adamp cloth for cleaning.

4. Attachments and Equipment

Never add anyattachments and/or equipment without approval of the manufacturer assuchadditions may

result in the risk of fire, electric shock or other personal injury.

5. Water and Moisture

Do not usethis'IV receiver where contact with or immersioninwater ispossible. Do not usenear bath

tubs, wash bowls, kitchen sinks,laundry tubs,swimming pools, etc.

6. Accessories

Do not placethis TV receiver on an unstable cart,stand,tripod, bracket, or table. The TV receiver mayfall,

causingserious injuryto a childor adult, and serious damageto the appliance. Use only

with a cart, stand,tripod, bracket, or table recommended by the manufacturer,or sold with

theTV receiver. Any mounting of the applianceshould follow the manufacturer's instruc-

tions, and should usea mounting accessoryrecommended bythe manufacturer.

An applianceand cart combinationshould be moved with care. Quick stops, excessive

force, and uneven surfacesmay causethe applianceand cart combination to overturn.

7. Ventilation

Slots and openingsin the cabinetare provided for ventilation and to ensure reliable operation of theTV

receiver and to protect it from overheating. Do not block these openingsor allow them to be blocked by

placingtheTV receiver on a bed,sofa,rug,or other similar surface. Nor should it be placed over a radiator

or heat register. If the TV receiver is to be placedin a rack or bookcase,ensurethat there is adequate

ventilation and that the manufacturer's instructions havebeen adhered to.

8. Power Source

This TV receiver should be operatedonlyfrom the type of power source indicated on the marking label. If

you are not sure of the type of power supplied to your home, consult your appliancedealer or local power

company.

9. Grounding or Polarization

This TV receiver isequipped with a polarized alternating current line plug havingone blade wider than the

other. This plug will fit into the power outlet only one way. Ifyou are unableto insertthe plug fully intothe

outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replaceyour

obsolete outlet. Do not defeat the safety purpose of the polarized plug.

I0. Power-Cord Protection

Power-supplycords should be routed so that they are not likely to be walked on or pinched by items placed

upon or againstthem, payingparticular attention to cords at plugs,convenience receptacles,and the point

where they exit from the appliance.

5

I I. Lightning

For added protection for thisTV receiver during a lightningstorm, or when it isleft unattended and unused

for long periods of time, unplug it from the wall outlet and disconnect the antennaor cable system. This will

prevent damageto theTV receiver due to lightning and power-line surges.

12. Power Lines

An outside antenna system should not be locatedinthe vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power linesor circuits. When installingan outside

antennasystem,extreme care should be taken to keep from touching such power lines or circuits ascontact

with them might be fatal.

13. Overloading

Do not overload walt outlets and extension cords asthis can result ina risk of fire or electric shock.

14. Object and Liquid Entry

Never pushobjects of anykind into thisTV receiver through openingsasthey maytouch dangerousvoltage

points or short-out parts that could result in a fire or electric shock. Never spill liquid of anykind on theTV

receiver.

EXAMPLE OF ANTENNA GROUNDING

15. Outdoor Antenna Grounding

If an outside antennaor cablesystem is connected to the TV receiver,be sure

the antenna or cable systemis grounded so asto provide some

protection againstvoltage surges andbuilt-up static charges.

Section 810 of the National Electrical Code,ANSI/NFPA

70-1984, provides information with respect to proper

grounding of the mast and supporting structure, grounding

of the lead in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge unit, con-

nection to grounding electrodes, and requirements for the

grounding electrode.

LEAD IN WIRE

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

:_.POWER SERVIC E GROUNDING

ELECTRODE SYSTEM

NEC -- NATIONAL ELECTRICAL CODE (NEC ART 250, PART H)

16. Servicing

Do not attempt to service this TV receiver yourself asopening or removing covers mayexpose you to

dangerousvoltage or other hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service

Unplug thisTV receiver from the walt outlet and refer servicing to qualified service personnel under the

following conditions:

(a)When the power-supply cord or plug isdamaged.

(b) If liquid hasbeen spilled,or objects havefallen into theTV receiver.

(c) If theTV receiver hasbeenexposed to rain or water.

(d) If theTV receiver does not operate normally by following the operating instructions,adjust only those

controls that are covered by the operating instructionsasan improperadjustment of other controls may

result indamageand will often require extensivework by a qualified technician to restore theTV receiver to

itsnormal operation.

(e) If theTV receiver hasbeen dropped or the cabinet hasbeen damaged.

(f)When theTV receiver exhibits a distinct changein performance -- this indicatesa need for service.

18. Replacement Parts

When replacement parts are required, be sure the service technician hasused replacement parts specified

by the manufacturer or havethe samecharacteristics asthe original part. Unauthorized substitutions may

result infire, electric shock or other hazards.

19. Safety Check

Upon completion of anyservice or repairs to this TV receiver,askthe service technician to perform safety

checksto determine that the TV receiver isin safeoperating condition.

0 ComponentVideo Input - for the best picture from DVD players

0 DiamondShield TM- protective screen shield

(Optional with VS-45607,VS-50607 & VS-60607)

0 IRIS TM - sensor that automatically adjusts brightness and contrast

0 Multibrand Remote Control - use one remote control for many

audio video components

0 PIP and POP - Picture-in-picture and Picture-outside-picture with

split screen mode

The following items are included with your newTV:

Remote Control

Active A/V Network Cable DJam°ndShEeld"

_ao_ory I_staBed on models V$-50707, VS-5S707, VS_0707

apd V S-70707

Optiona] for models V$-45607, VS-50607, VS_Z_607

(2),_ S

Batteries

The connections shown in this book are general. Cable systems as well as individual audio and/or

video components can vary from those shown here. The first diagrams show basic connections

to antenna or cable systems. After you have completed these, you can then connect any addi-

tional components (stereo, DVD, AV receiver, etc.).

IMPORTANT

To maximize your system for its best

performance, your dealer can help you

customize hookups and sell you any

additional connection accessories that

may be needed for your individual

equipment.

7

0 Hooking up yourTV to an antenna or wall outlet cable

0 Remote control functions - pages 19-20

0 Menu screen summaries - page 22-24

0 Selecting the input - page 3 I

0 Setting theV-chip parent lock - page 33

0 Picture-in-picture mode - page 50

0 Picture-outside-picture mode - page 52

0Troubleshooting - page 57

- page 9

TV to Antenna orWall Outlet Cable

Separate UHF andVHF antennas

I. Connect the UHF andVHF

antenna leads to the UHF/VHF

combiner.

2. Press the combiner ontoANT-A

on the TV back panel.

VNF Antenna UHF A_teer_

(C_neE_ 14"_9)

F_atTw_ Lead F_t T_

1

Ex[emal

A_terna

0r Ca_e

L PTIONAL*

Oemb_r_r

Baok S_e

TV Sack Panel

ANT._,

.@@@

®

oo

®®

®@

o

o 6

@@@

o6'%0

*there are different combiners for different wires.

Check with your dealer for the combiner style that you need,

Twin lead antenna or wall outlet cable

For antenna with twin fiat

leads

I. Connect the 300 ohm twin leads to

the transformer.

2. Push the 75 ohm side of the trans-

former onto ANT-A on the TV

back panel.

For cable or antenna with

coaxial lead

Connect the incoming cable to

ANT-A on the TV back panel,

000.....L/

Twin Load

J

/

_a_Hng T_ndo_er

TV Back PaneI

ANT A

@@@

®

o

@

®®

®@

o

@@

@o@

Connection of TV to Cable Box

I. Connect the incoming cable to

ANT-A on theTV back panel.

2. Connect two coaxial cables as

follows:

• One from CABLE LOOP-OUT on

theTV back panel to IN on the

back of the cable box,

• One from OUT on the back of the

cable box to ANT-B on theTV

back panel,

incoming Cabl_

TVBack Panel

@o @G@

m_ALOep_U_TB

o_ _o®

Cable Box

rear terminals

Connection ofTV toVCR and Cable Box

I. Connect the incoming cable toANT-A

on the TV back panel.

2. Connect three coaxial cables as follows:

• One from CABLE LOOP-OUT on the

TV back panel to IN on the back of the

cable box.

• One from OUT on the back of the

cable box to ANTENNA IN on the

VCR back panel.

• One from ANTENNA OUT on the

VCR back panel to ANT-B on the TV

back panel.

TV Back pan_

©

®

.... ®®

ANT_L_OUT ANT,B

®®

©

VCR Back panel

If your VCR has a video chant=el

ON/OFF sw_tch_ set it to OFF,

Audio Video Connections

I. Connect a video cable fromVIDEO

OUT on theVCR back panel toVIDEO

INPUT I or INPUT 2 on theTV back

panel.

If you have a S-VHSVCR, follow the

same steps, using the S-Video terminals

on the VCR and TV.

2. Connect a set of audio cables from

AUDIO OUT on theVCR back panel

to AUDIO INPUT on the TV back

panel. The red cable connects to the R

(right) channel and the white cable

connects to the L (left). If yourVCR is

non-stereo, connect only the L (left)

cable.

TV _ck P_e_

RCA

cab_

VCR _ck pa_el

If your VCR has a video channel

ON/OFF s_wltch, set it to OFF,

_ F_CA pin-ly

video caSe_

A_tac_

only

cat_e

type

type cable

10

Connection ofTV toVCg and Antenna or

Wall Outlet Cable

Antenna/Cable Connections

I. Connect the incoming cable toANT-A

on theTV back panel.

2. Connect two coaxial cables as follows:

• One from CABLE LOOP-OUT on the

TV back panel toANTENNA IN on the

VCR back panel.

• One fromVCR back panelANTENNA

OUT to ANT-B on the TV back panel.

If your VCR has a video channel

OWOFF swltch_ set It to OFF,

®®

®

Audio/Video Connections

I. Connect a video cable fromVIDEO

OUT on theVCR back panel toVIDEO

INPUT I or INPUT 2 on theTV back

panel.

If you have a S-VHS VCR, follow the

same steps, using the S-Video terminals

on the VCR and TV.

2. Connect a set of audio cables from

AUDIO OUT on theVCR back panel to

AUDIO INPUT on theTV back panel.

The red cable connects to the R (right)

channel and the white cable connects to

the L (left). If yourVCR is non-stereo,

only connect the L (left) cable.

©

OUT

OPTIONAL

_ypOc_b_e

VCRBackPanel

If your VCR has

a video channel

ON/OFF switch,

set it to OFF.

TV Back Panel

o'_

o I

Wh_e

O ROd 0

v_eoc_bJo

®

II

Connection of TV to Stereo Audio System

I. Connect the audio cables from AUDIO

MONITOR OUTPUT on the TV back

panel toTV IN orAUX IN terminals on

the back of the audio system. The red

cable connects to the R (right) channel

and the white cable connects to the L

(left) channel.

2. Turn off theTV's speakers through theAV

Connection Menu (page 27-28).

3. Set the audio system's input to theTV or

AUX position to hear the TV's audio

through your stereo system.

Audio system rear terminals

TV Back patleE

of _6

o @@

®® .a_® ® @

®

Connection of TV to the Active A/V Network

To control your Mitsubishi audio and/or video products with one remote control

Connect the A/V network cable from

ACTIVE A/V NETWORK on theTV

back panel to IN on the back of a

Mitsubishi component that hasA/V

networkterminaL

Turn the ACTIVE A/V NETWORK on,

through the AV CONNECTION menu

(pages 27-29).

Check the Owner's Guide of your

added Mitsubishi components to

ensure the best possible connections.

M#subishi Component rear tem]Jna_s

TV Back Panel

®®

@@@

ACTIVEAN

NETWORK

12

Connection of TV to AV Receiver

I. Connect a video cable from VIDEO

MONITOR OUT on the back of the AV

Receiver toVIDEO INPUT I on theTV

back panel using aVIDEO cable,

2. Connect a video cable fromVIDEO

MONITOR OUTPUT on theTV back

panel toVIDEOTV IN on the back of

the AV Receiver.

3. Connect a set of audio cables from

AUDIO OUTPUT on the TV back

panel toAUDIOTV IN on the back of

the AV Receiver. The red cable con-

nects to the R (right) channel and the

white cable connects to the L (left)

channel,

TV Back p_'_

®

AV RECEIVER

13

Connection of TV to DVD with ComponentVideo

Outputs

IMPORTANT

For Digital Audio connections, see

the Owner's Guides of your DVD

Player and AV Receiver.

For ComponentVideo Connections

I. Connect the ComponentVideo cables

from VIDEO OUT on the back of the

DVD player to DVDVIDEO INPUT on

theTV back panel, matching the correct

components:

• Y toY,

Cr to Cr,

Cb to Cb.

2. Connect a set of audio cables from

AUDIO OUT on the back of the DVD

player to DVD AUDIO INPUT on the

TV back panel. The red cable connects

to the R (right) channel and the white

cable connects to the L (left) channel.

TV Back Panel

I 0

0

DVD Rear Terminal

Warning: Don't display the same stationary images on the screen for more than 15%of your total TV

viewing in one week Examples of stationary images are letterbox top/bottom bars from DVD disc or

other video sources, side bars when showing standard TV pictures on widescreen TV's, stock market

reports, video game patterns, station logs, web sites or stationary computer images. Such patterns can

unevenly age the picture tubes causing permanent damage to the TV. Please see page 58 for a detailed

explanation.

14

For Models VS-45607

VS-50607 and VS-60607

Additional features of Models

VS-50707, VS-55707,VS-60707

and VS-70707

GUIDE button

for DSS systems

15

OperatingYour Remote Control

Installing the batteries

I. Removethe back cover of the remote control by pushingthe

tab in the direction of the arrow and sliding offthe cover.

2.Load the batteries, makingsure the polarities(+) and (-) are correct.

iMPORTANT

When you replace the batteries in your remote

control, the remote may return to its initial

setting. You may need to set up your remote

again.

For best results

Be within 20 feet of the equipment when using the remote control.

Don't press two or more buttons at the same time, unless you are

specifically instructed to do so in this owner's guide.

Don't allow the remote control to get wet or become heated.

Avoid dropping the remote control on a hard surface.

When cleaning the remote control, don't use any harsh chemicals.

Use only a soft, slightly moistened cloth.

Don't mix new batteries with old ones.

Don't heat, take apart, or throw batteries into a fire.

Use AAA alkaline batteries.

Using the remote control with yourTV

You can use your remote to control theTV, CABLE/DBS,VCR,

DVD or AUDIO. The remote has been preset to operate the

TV and other Mitsubishi products. It can be set to control

other audio/video equipment.

To operate the TV, the select switch at the top of the remote

should be set toTV.

16

o oo 0

O O O

0 O 0

0 O O_

Remote Control of Other Audio and Video Products

Programming the Remote to Control Other Audio andVideo Products:

Move the slide switch at the top of the remote to select the

audio or video product you want to control,

Press and hold the POWER button, so that it stays down when

you enter the code.

Enter the code for the equipment from the appropriate list,

exactly as stated. If there ismore than one code number, start

with the first number. After setting the code, release the

POWER button.

Point the remote at the equipment and press the POWER

button. If it is on and turns off or is off and turns on, the

remote will control the equipment. If not, try the next number.

Cable Box codes:

Cable box brand codeto ente_ If your

General Instruments/ 111,119, 120, 121,122, cable box

Jerrold 123, 124, 125, 126, 127 code is not

Oak 102, 137, 139 listed here,

please see

Pioneer 101, 116 page 63

Scientific Atlanta 111,112,113 for a

Zenith 100, 117 complete

To reset to default code. enter 000 listina.

Satellite Receiver codes:

VCR

CABLF.JDBS

TV

IMPORTANT

If you cannot turn the cable box ON by

pressing POWER, try pressing the

CHANNEL or the number buttons.

Satellite brand

Mitsubishi

Echostar/Dishnetwork

Hughes-DSS

RCA-DSS

Sony*DSS

Toshiba*DSS

Panasonic*DSS

Primestar

code to enter:

173

175

173

176

177

170

174

178

If your

sateUite

code is not

listed here

]lease see

page 63

for a

complete

listing,

To reset to default code, enter 000

VCR codes:

VCR brand codeto enter:

If your

Mitsubishi 001,002 VCR

Hitachi 020, 043, 065 code is not

JVC 030, 054, 059 listed here,

Philips/Magnavox 043, 044, 051 please see

Panasonic 041,042, 043 page 64

RCA 020, 053, 065 for a

Sony 048, 049, 050 complete

Toshiba 021,066 listing.

To reset to default code, enter 000

VCR

CABLE/DBS 1 DVD

Tvl,I

VCR

CABLE/DBS

IMPORTANT

When set toTV, the PLAY, STOP, REW/

REV and the FF/FWD keys will operate

theVCR after theVCR codes have been

chosen.

17

Remote Control of Other Audio and Video Prod-

uct, continued

DVD Player codes:

DVD/LDP brand codeto enter:

Mitsubishi (DVD) 003

Mitsubishi (LDP) 016, 017

Panasonic 250

Pioneer DVD (LDP) 252 (016,017)

Sony 254

Toshiba 253

TO reset to default code, enter 000

Ifyour

DVD code

is not

listed here,

please see

page 63

for a

complete

listing.

vcn

CASL_DBS

AV Receiver codes:

Audio brand

Mitsubishi AV _ceiver

Mitsubishi CD player

Kenwood

Onkyo

Pioneer

Sony

Yamaha

code_e_er:

010,011,012

013,014,015

200,208

209,214

205,207

222

201,202

If your

Audio

code is not

listed here,

please see

page 63

for a

complete

To reset to default code, enter 000 listing.

VCR

CASL_DSS

TV IOlO

IMPORTANT

If the slide switch is set toTV when you enter anAV receiver code,VOLUME

and MUTE will be controlled by theAV receiver, rather than theTV. To

returnVOLUME and MUTE control to theTV, set the slide switch toTV,

,ress and hold POWER and enter 000.

Additional slide switch feature: for multiple A/V component systems

Your Mitsubishi remote control was designedfor flexibility in both large and small A/V systems.

For example, you can use the slide switch in the following way:

If you have twoVCR's, but no DVD player, move the slide switch to the DVD position and enter

the secondVCR code. Then when the slide switch is moved to DVD you can control the second

VCR.

The following chart shows which device can be entered for each position. Only one device is

allowed for each slide switch position.

TV position: Cable/DBS position: DVD position: VCR position: Audio position:

• TV • cable box • DVD • VCR • AV receiver

• A/V receiver • sateUitereceiver • VCR • Mitsubishi DVD • Mitsubishi CD player

(volume, mute only) • cable box player • cabe box

IMPORTANT

Some manufacturers may change their products, or they may use more

than one remote control system. If this is the case, your remote may not

be able to operate yourYCR, Cable Box, Satellite Receiver orAV Receiver.

18

Remote Control Functions

Slide switch

Selects which A/V

will be controlled by the

remot_

Numbers

To individually select

channels or enter

information into TV

SQV (SuperQuickView TM)

Scan through a memorized list of

favorite channels

Power

power on and off for theTV

or other A/V products

QV (QuickView _')

-- Switchesto lastchannelviewed

INPUT

Selects the signal you will watch (Ant

A; Ant B; Input I, 2 or 3; DVD)

CHANNEL

View channels in increasing or

decreasing numerical order

VOLUME

Increasesor decreasessound

SLEEP

Sets theTV to turn off

within 2 hours

VIDEO

Individually adjusts theVideo

settings

AUDIO

r adjusts

the Audio settings

MUTE

Turns on or off the sound

19

Remote Control Functions, continued

ENTER

Use after selecting a

channelnumber or

menu item

LIGHT

ForVS-50707,VS-55707,VS-60707

andVS-70707,pressto lightup

the remote control

CANCEL

ClearSQVandsome

menuentries

PIP/POP Keys

Use to display,move,

resize or changea PIP

or POPchannel.

ADJUST

Selects menu items.

Moves the PIP

on-screen location

GUIDE

ForVS-50707,VS-55707,

VS-60707 andVS-70707.

satellite systems program

guides

MENU

Displayson-screen menu

choices

and

• g

INFO

_Displays an on-screen

summary ofcurrentTV

settings

REC

Manually record

programs on

REW/REV

Rewind and reverse search for

theVCR. Skip reverse for CD.

Reverse scan for DVD

PLAY

PlaysaVCR, DVD or C

STOP

TOstop aVCR, DVD or

PAUSE

VCR, DVD or CD or

freezesthe PIP/POP

FF/FWD

Fast forward or forward search

for aVCR. Skipforward for a CD.

Fastplayfor a DVD

2O

YourtelevisionhasMitsubishi'sexclusiveI_l_lllon screen operating system, which provides on-

screen information for menu choices and changes.

A highlighted icon isshown when

there isanother menu levelfor your

choices. Pressingthe ENTER button

will displaythe menu options.

Make choices or changes to a menu

item when you see a button.

TheViewPoint system includesthe following special features:

The selected icon or button is highlightedwith a yellow outline and

the text color will be yellow.

On-screen instructions provide complete menu choice information.

O0

Some on-screen menu options must be set before other options are

available. For example,"Set theTimer" will only be possible if

"ClockTime" and "Set Day" have been set.

Making Selections:

lUST A or • to select the menu item you want to change

ADJUST _ to move to the selection field

ADJUST • or • to change the settings

UST 4 to move back to the menu item

• • _ ENTER E_to select an option, or start an automatic function

•CANCELC_ Lto clear a setting, or stop an automatic function

To exit the on-screen menus:

MENU Pressthe MENU key to move back one menu screen at a time

until you exit all the menus to return to television viewing

OR

PressHOME to exit all menus with one keystroke and return to

television viewing

21

Page is loading ...

Mitsubishi VS-45607 User manual

Mitsubishi VS-45607 User manual

Related papers

Other documents