Supermicro 1026T-6RFT+ User manual

Brand: Supermicro

Model: 1026T-6RFT+

Category: Server barebones

Type: User manual

This manual is also suitable for

SUPERSERVER 1026T-6RFT+

SUPERSERVER 1026T-6RF+

SUPER

USER’S MANUAL

1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and docu-

mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.

Any use or reproduction of this product is not allowed, except as expressly permitted by the terms

of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A

digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the manufacturer’s instruction manual, may cause harmful interference

with radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-

ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to the

State of California to cause birth defects and other repro-

ductive harm.

Manual Revision 1.0

Release Date: January 12, 2011

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.

It provides information for the installation and use of the SuperServer 1026T-

6RFT+/1026T-6F+. Installation and maintenance should be performed by experi-

enced technicians only.

Manual Organization

Chapter 1: Introduction

The ﬁ rst chapter provides a checklist of the main components included with the

server system and describes the main features of the X8DTU-6TF+/X8DTU-6F+

serverboard and the SC119TQ-R700UB chassis, which comprise the SuperServer

1026T-6RFT+/1026T-6F+.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer into a rack and

check out the server conﬁ guration prior to powering up the system. If your server

was ordered without processor and memory components, this chapter will refer you

to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

SuperServer 1026T-6RFT+/1026T-6F+.

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X8DTU-6TF+/X8DTU-6F+

serverboard, including the locations and functions of connections, headers and

jumpers. Refer to this chapter when adding or removing processors or main memory

and when reconﬁ guring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC119TQ-R700UB server chassis.

You should follow the procedures given in this chapter when installing, removing or

reconﬁ guring SAS or peripheral drives and when replacing system power supply

modules and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: System Speciﬁ cations

Preface

Notes

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

Onboard SAS ..................................................................................................1-2

Onboard Serial ATA ........................................................................................ 1-2

Rear I/O Ports .................................................................................................1-2

Graphics Controller .........................................................................................1-3

Other Features ................................................................................................1-3

1-3 Server Chassis Features ................................................................................1-3

System Power .................................................................................................1-3

Hard Drives .....................................................................................................1-3

PCI Expansion Slots .......................................................................................1-3

Front Control Panel .........................................................................................1-4

Cooling System ...............................................................................................1-4

1-4 Contacting Supermicro ....................................................................................1-6

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup .........................................................................................2-1

Choosing a Setup Location .............................................................................2-1

Rack Precautions ............................................................................................2-2

Server Precautions ..........................................................................................2-2

Rack Mounting Considerations .......................................................................2-3

Ambient Operating Temperature ................................................................2-3

Reduced Airﬂ ow .........................................................................................2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading .....................................................................................2-3

Reliable Ground ......................................................................................... 2-3

2-4 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails ......................................................2-4

Inner Rails .......................................................................................................2-5

Outer Rails ...................................................................................................... 2-6

2-5 Checking the Serverboard Setup .................................................................... 2-8

Installing the Server into a Telco Rack ...........................................................2-8

vii

Table of Contents

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-2 Control Panel Buttons ..................................................................................... 3-1

UID ..................................................................................................................3-1

Reset ...............................................................................................................3-1

Power ..............................................................................................................3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

UID/Overheat/Fan Fail/Power Fail .................................................................. 3-2

NIC2 ................................................................................................................3-2

NIC1 ................................................................................................................3-2

HDD .................................................................................................................3-3

Power ..............................................................................................................3-3

3-4 Drive Carrier LEDs .......................................................................................... 3-3

Chapter 4 System Safety

4-1 Electrical Safety Precautions .......................................................................... 4-1

4-2 General Safety Precautions ............................................................................ 4-2

4-3 ESD Precautions .............................................................................................4-3

4-4 Operating Precautions .................................................................................... 4-4

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-1

5-2 Processor and Heatsink Installation................................................................5-2

Installing LGA1366 Processors ....................................................................... 5-2

Installing the Heatsink ..................................................................................... 5-4

Removing the Heatsink ................................................................................... 5-5

5-3 Connecting Cables ..........................................................................................5-6

Connecting Data Cables ................................................................................. 5-6

Connecting Power Cables ..............................................................................5-6

Connecting the Control Panel ......................................................................... 5-6

5-4 I/O Ports ..........................................................................................................5-7

5-5 Installing Memory ............................................................................................ 5-8

5-6 Adding PCI Cards .........................................................................................5-12

5-7 Serverboard Details ...................................................................................... 5-13

X8DTU-6TF+/X8DTU-6F+ Quick Reference .................................................5-14

5-8 Connector Deﬁ nitions .................................................................................... 5-15

5-9 Jumper Settings ............................................................................................5-23

5-10 Onboard Indicators ........................................................................................5-25

viii

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

5-11 SATA Port Connections ................................................................................. 5-27

5-12 Installing Software .........................................................................................5-28

Supero Doctor III ........................................................................................... 5-29

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

6-3 System Fans ...................................................................................................6-2

System Fan Failure ......................................................................................... 6-3

Air Shroud ....................................................................................................... 6-4

Hard Drive Installation .....................................................................................6-6

Hard Drive Backplane ..................................................................................... 6-8

DVD-ROM Drive Installation ........................................................................... 6-8

6-4 Power Supply .................................................................................................. 6-9

Power Supply Failure ......................................................................................6-9

Chapter 7 BIOS

7-1 Introduction ......................................................................................................7-1

Starting BIOS Setup Utility ..............................................................................7-1

How To Change the Conﬁ guration Data .........................................................7-1

Starting the Setup Utility .................................................................................7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Setup Conﬁ gurations......................................................................7-4

7-4 Security Settings ...........................................................................................7-25

7-5 Boot Conﬁ guration ........................................................................................ 7-27

7-6 Exit Options ...................................................................................................7-28

Appendix A BIOS Error Beep Codes

Appendix B System Speciﬁ cations

Chapter 1

Introduction

1-1 Overview

The SuperServer 1026T-6RFT+/1026T-6F+ is a high-end server comprised of two

main subsystems: the SC119TQ-R700UB 1U server chassis and the X8DTU-6TF+/

X8DTU-6F+ dual processor serverboard. Please refer to our web site for informa-

tion on operating systems that have been certiﬁ ed for use with the system (www.

supermicro.com).

In addition to the serverboard and chassis, various hardware components have

been included with the 1026T-6RFT+/1026T-6F+, as listed below:

One slim DVD-ROM drive (DVM-TEAC-DVD-SBT)

•

Five sets of 4-cm counter-rotating fans (FAN-0101L4)•

One air shroud (MCP-310-81901-0B)•

Two passive CPU heatsinks (SNK-P0037P)•

Riser Cards: (see Section 5-6 for details) •

One RSC-R1UU-2E8

One RSC-R1UU-E8R+

SAS Accessories

•

One SAS backplane (BPN-SAS-815TQ)

One SAS cable (CBL-0044L)

Eight drive carriers (MCP-220-00047-0B)

One rackmount kit (MCP-290-00062-0N)

•

One CD containing drivers and utilities•

SuperServer 1026T-6RFT+/1026T-6F+ User's Manual•

Chapter 1: Introduction

1-1

1-2

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

1-2 Serverboard Features

At the heart of the SuperServer 1026T-6RFT+/1026T-6F+ lies the X8DTU-6TF+/

X8DTU-6F+, a dual processor serverboard based on the Intel® 5520 chipset. Below

are the main features of the serverboard. (See Figure 1-1 for a block diagram of

the chipset).

Processors

The X8DTU-6TF+/X8DTU-6F+ supports single or dual Intel® 5500/5600 Series

processors in LGA1366 sockets. Please refer to our web site for a complete listing

of supported processors (www.supermicro.com).

Memory

The X8DTU-6TF+/X8DTU-6F+ features 18 DIMM sockets that can support up to 192

GB of registered ECC DDR3-1333/1066/800 or 48 GB of unbuffered ECC/non-ECC

DDR3-1333/1066/800 SDRAM. Please refer to Chapter 5 for installing memory.

Onboard SAS

An onboard LSI 2108 SAS controller in integrated into the X8DTU-6TF+/X8DTU-

6F+. The hot-swap SAS drives are connected to a backplane that provides power,

bus termination and conﬁ guration settings.

Note: The operating system you use must have RAID support to enable the

hot-swap capability and RAID function of the SAS drives. RAID 0, 1, 5, 6,

10, 50 and 60 is supported. Refer to the following ftp site for setup guidelines

<ftp://ftp.supermicro.com/driver/SAS/LSI/LSI_SAS_EmbMRAID_SWUG.pdf>.

Onboard Serial ATA

An on-chip (ICH10R) SATA controller is integrated into the X8DTU-6TF+/X8DTU-

6F+ to provide a six-port, 3 Gb/sec SATA subsystem, which is RAID 0, 1, 5 and

10 supported (RAID 5 is supported with Windows OS only). The SATA drives are

hot-swappable units.

Note: You must have RAID set up to enable the hot-swap capability of the SATA

drives. Documentation on RAID setup guidelines can be found on our web site.

Rear I/O Ports

The color-coded I/O ports include one COM port, a VGA (monitor) port, two USB

2.0 ports, PS/2 mouse and keyboard ports, one dedicated IPMI LAN port and two

1-3

Chapter 1: Introduction

gigabit Ethernet ports. The 1026T-6RFT+ (X8DTU-6TF+) includes two additional

10 Gb Ethernet ports.

Graphics Controller

The X8DTU-6TF+/X8DTU-6F+ features an integrated Matrox G200eW graphics

chip.

Other Features

Other onboard features that promote system health include onboard voltage moni-

tors, auto-switching voltage regulators, chassis and CPU overheat sensors, virus

protection and BIOS rescue.

1-3 Server Chassis Features

The 1026T-6RFT+/1026T-6F+ is built upon the SC119TQ-R700UB chassis. Details

on the chassis and on servicing procedures can be found in Chapter 6.The following

is a general outline of the main features of the chassis.

System Power

The SC119TQ-R700UB features a redundant 700W power supply consisting of

two power modules. The system does not need to be shut down when replacing or

removing a single power supply module.

Hard Drives

The SC119TQ-R700UB chassis was designed to support eight hot-swap SAS

hard drives.

PCI Expansion Slots

Two riser cards are included. The RSC-R1UU-E8R+ is located on the right side of

the chassis and supports one low-proﬁ le PCI-E x4 card. The RSC-R1UU-2E8 is

located on the left side of the chassis and supports two PCI-E x8 add-on cards.

See section 5-6 of this manual for details.

1-4

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

Front Control Panel

The chassis' control panel provides you with system monitoring and control. LEDs

indicate system power, HDD activity, network activity (2), overheat/fan/power failure

and UID (Unit Identiﬁ er). A main power button and a UID button is also included.

Cooling System

The SC119TQ-R700UBP has an innovative cooling design that features ﬁ ve sets

of 4-cm counter-rotating fans located in the middle section of the chassis. There

is a "Fan Speed Control Mode" setting in BIOS that allows chassis fan speed to

be determined by system temperature. The power supply module also includes a

cooling fan.

1-5

Chapter 1: Introduction

Figure 1-1. Intel 5520 + IOH-36D/ICH10R Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

Processor#1

QPI

DDR3 DIMM

3,4

BMC

VGA SWITCH

ESI

SPI

ATMEL

AT25DF321

CLINK

PCIE Port 1-4

PCI-E x8

Gen2 x16

Gen2 x8

ICH10R

ESI

IOH

36D

PORT0

PORT

7,8,9,10

5,6

PCI-E x16

PORT

PCI-Ex8

in x4 slot

RJ45

COMA

COMB

SIO

PS2 KB/MS

USB 0/1

USB

QPI

Gen2 x8

PORT

8,10

(Lane Reversal)

SATA #2

SATA #3

SATA #4

SATA #5

SATA #0

SATA

PCI

USB

TPM

LPC

PORT1 PORT1

Gen2 x4

PORT

1,2

in x16 slot

VGA VGA

KAWELA

RJ45 RJ45

Gen1x2

KAWELA

RJ45 RJ45

Gen1 x4

PCIE Port 5-6

Processor#0

SATA #1

USB 2/3

USB 4/5

USB 6

USB 7

PORT0

1-6

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Paciﬁ c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8228-1366, ext.132 or 139

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your 1026T-6RFT+/1026T-6F+

up and running. Following these steps in the order given should enable you to have

the system operational within a minimum amount of time. This quick setup assumes

that your system has come to you with the processors and memory pre-installed. If

your system is not already fully integrated with a serverboard, processors, system

memory etc., please turn to the chapter or section noted in each step for details on

installing speciﬁ c components.

2-2 Unpacking the System

You should inspect the box the 1026T-6RFT+/1026T-6F+ was shipped in and note

if it was damaged in any way. If the server itself shows damage you should ﬁ le a

damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the server. It should be

situated in a clean, dust-free area that is well ventilated. Avoid areas where heat,

electrical noise and electromagnetic ﬁ elds are generated. You will also need it placed

near a grounded power outlet. Be sure to read the Rack and Server Precautions

in the next section.

2-3 Preparing for Setup

The box the server was shipped in should include two sets of rail assemblies, two

rail mounting brackets and the mounting screws you will need to install the system

into the rack. Follow the steps in the order given to complete the installation process

in a minimum amount of time. Please read this section in its entirety before you

begin the installation procedure outlined in the sections that follow.

Choosing a Setup Location

Leave enough clearance in front of the rack to enable you to open the front door •

completely (~25 inches) and approximately 30 inches of clearance in the back

of the rack to allow for sufﬁ cient airﬂ ow and ease in servicing.This product is for

2-2

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

Warnings and Precautions!

installation only in a Restricted Access Location (dedicated equipment rooms,

service closets and the like).

This product is not suitable for use with visual display work place devices

•

acccording to §2 of the the German Ordinance for Work with Visual Display

Units.

Rack Precautions

Ensure that the leveling jacks on the bottom of the rack are fully extended to •

the ﬂ oor with the full weight of the rack resting on them.

In single rack installation, stabilizers should be attached to the rack. In multiple

•

rack installations, the racks should be coupled together.

Always make sure the rack is stable before extending a component from the

•

rack.

You should extend only one component at a time - extending two or more si-

•

multaneously may cause the rack to become unstable.

Server Precautions

Review the electrical and general safety precautions in Chapter 4.•

Determine the placement of each component in the rack • before you install the

rails.

Install the heaviest server components on the bottom of the rack ﬁ rst, and then

•

work up.

Use a regulating uninterruptible power supply (UPS) to protect the server from

•

power surges, voltage spikes and to keep your system operating in case of a

power failure.

Allow the hot plug SAS drives and power supply modules to cool before touch-

•

ing them.

Always keep the rack's front door and all panels and components on the servers

•

closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera-

ture of the rack environment may be greater than the ambient temperature of the

room. Therefore, consideration should be given to installing the equipment in an

environment compatible with the manufacturer’s maximum rated ambient tempera-

ture (Tmra).

Reduced Airﬂ ow

Equipment should be mounted into a rack so that the amount of airﬂ ow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply connec-

tions other than the direct connections to the branch circuit (i.e. the use of power

strips, etc.).

2-4

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

2-4 Installing the System into a Rack

This section provides information on installing the server into a rack unit with the

rack rails provided. If the system has already been mounted into a rack, you can

skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on the market,

which may mean the assembly procedure will differ slightly. You should also refer to

the installation instructions that came with the rack unit you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies in the rack mounting kit. Each

assembly consists of two sections: an inner ﬁ xed chassis rail that secures directly

to the server chassis and an outer ﬁ xed rack rail that secures directly to the rack

itself (see Figure 2-1).

Note: The rails will ﬁ t a rack between 26" and 33.5" deep.

Figure 2-1. Identifying the Inner Rails and Inner Rail Extensions

Inner Rails

(Inner rails are pre-installed

on the chassis)

Inner Rail

Extensions

Chapter 2: Server Installation

2-5

Inner Rails

The SC119 chassis inner rails are composed of two sections: inner rails and inner

rail extensions. The inner rails are pre-attached and do not interfere with normal use

of the chassis if you decide not to use a server rack. Attach the inner rail extension

to stabilize the chassis within the rack.

Installing the Inner Rails

Place the inner rail extensions on the side of the chassis aligning the hooks 1.

of the chassis with the rail extension holes. Make sure the extension faces

"outward" just like the pre-attached inner rail.

Slide the extension toward the front of the chassis.2.

Secure the chassis with 2 screws as illustrated.3.

Repeat steps 1-3 for the other inner rail extension.4.

Figure 2-2: Identifying the Sections of the Rack Rails

(right side rail shown)

2-6

SUPERSERVER 1026T-6RFT+/1026T-6F+ User's Manual

Outer Rails

Installing the Outer Rails to the Rack

Attach the shorter outer rail to the outside of the longer outer rail. You must 1.

align the pins with the slides. Both bracket ends must face the same direction.

Adjust the outer rails so that they ﬁ t snugly within the rack.2.

Secure the longer outer rail to the front of the rackl with two screws3.

Secire the shorter outer rail to the rear rack with three screws. 4.

Repeat steps 1-4 for the remaining outer rail.5.

Locking Tabs

Both chassis rails have a locking tab, which serves two functions. The ﬁ rst is to

lock the server into place when installed and pushed fully into the rack, which is

its normal position. Secondly, these tabs also lock the server in place when fully

extended from the rack. This prevents the server from coming completely out of

the rack when you pull it out for servicing.

Secure to the

Front of the

Rack

Secure to the

Rear of the Rack

Figure 2-3. Assembling the Outer Rails

Attach Outer Rails

Together

Page is loading ...

Supermicro 1026T-6RFT+ User manual

Brand: Supermicro

Model: 1026T-6RFT+

Category: Server barebones

Type: User manual

This manual is also suitable for

Download PDF

report

Supermicro 1026T-6RFT+ User manual

This manual is also suitable for

Supermicro 1026T-6RFT+ User manual

Related papers

Other documents