Individual Components for NDR-LD System:
NDR-n-LD Master station (10, 20, 30, 40-station) for Long Distance
IE-JA-NLD Flush mount long distance sub with stainless steel cover
IF-DA-NLD Surface mount long distance sub, brown plastic
PC-359B Call holding circuit board for sub station, mounted externally
PS-2410A: 24V DC Power Supply (for 10 and 20 station masters)
PS-24E: 24V DC, 2A Power Supply (for 30 and 40 station masters)
SUB STATION MOUNTING:
IE-JA-NLD: 2-gang electrical box
IF-DA-NLD: Surface mounts to 1-gang box
- INSTRUCTIONS -
The NDR-LD Long Distance Lamp Memory System is designed for communication with remote stations
located up to 4,000' away, or to each elevator in a building. Sub stations are available in surface or
flush mount styles, and require a separate circuit board (PC-359B) to be added for the call-in function.
Three wires are required to each sub station. One RY-PA is required per contact closure. Additional
wires are required for extra contacts to activate external devices.
NDR-LD
NDR CCTV Call Up and Door Release System for Long Distances and Elevators
NDR-n-LD Master Station
IF-DA-NLD and IE-JA-NLD Sub Stations
Special
Order
Products
Pg. 1
WIRING DIAGRAM: SYSTEM USED FOR CCTV CAMERA CALL-UP
1
2
2
3
4
5 6 7
7
7
7
8
9
PC-359B (Solder side view)
Solder pads:
Numbered by
location on
board.
To 1
To 2
To Blk
To Blk
1
L
2
RY-PA
#1
BLK
H
RY-PA
#2
NDR-LD Master
RY-PA
#1
RY-PA
#2
BLK
BLK
BLK
YEL
Momentary closure #1
YEL
Constant closure #1
YEL
Momentary
closure #2
YEL
Constant
closure #2
Equipment for each station that requires
both a constant closure and momentary
closure when a channel is selected:
2 RY-PA relays
1 Diode (1N4001)
DUAL FUNCTIONS FROM EACH CHANNEL:
Terminal Block
NDR-LD TERMINAL DEFINITIONS:
+ Positive 24V DC
- Negative
1~40 Station number
E Common communication
H Provides power to sub station
Normally Open contacts remain
closed as long as master has sub
station selected.
NDR-20-LD
+
-
PS-2410A
External
Terminal Block
1
2
~
20
L
Closure for Station #2
BLKYEL
Closure for Station #1
RY-PA
#1
BLK YEL
RY-PA
#3
1
2
2
3
4
5
6
7
7
7
7
8
9
PC-359B
IF-DA-NLD
1
2
Blk
Blk
WHT
Wire
1
2
3
~
20
E
H
+
-
IE-JA-NLD
1
2
Blk
Blk
3
1
2
2
3
4
5
6
7
7
7
7
8
9
PC-359B
1
2
2
3
4
5
6
7
7
7
7
8
9
PC-359B
IF-DA-NLD
1
2
Blk
Blk
WHT
Wire
IE-JA-NLD
1
2
Blk
Blk
3
1
2
2
3
4
5
6
7
7
7
7
8
9
PC-359B
OPERATION:
1. When a sub station places a call, the red channel LED indicator lights and a call tone rings at the master. The
tone and light will remain activated until the call is answered, which is the primary function of the PC-359B. The
LED indicator at the sub station will be lit from the time the call is placed until it is answered.
2. If the master station is talking to another sub station, a new call from another sub station will light the LED, but
the call tone will not be heard.
3. When the call is answered, the LED on the master goes off. The person at the master uses the push-to-talk,
release-to-listen button, or picks up the handset to speak (with NEM-A masters). The LED at the sub station will
go off when the master answers.
4. When the conversation is completed, the OFF button to the left of the station selector button must be pressed to
disengage the call.
SPECIFICATIONS:
Power Source: 24V DC at master. Use PS-2410A or PS-24E.
Communication Output: 500mW at 20 ohms
Communication: Push-to-talk, release-to-listen or VOX handset at master.
Hands free at sub station.
Calling: Master to sub: By voice only after pretone.
Sub to master: Call tone and LED, remaining activated until call is answered.
Wiring: 2 common plus 1 individual per sub, looped; or 3 conductors homerun to each sub.
Shielded cable is recommended.
Use Aiphone #822203 for homerun wiring, #822206 for 4 stations
on each run, or #822210 for up to 8 stations on each run.
Wiring Distance: 2,000' with 22AWG; 4,000' with 18AWG.
Dimensions (H x W x D): IE-JA-NLD: 4-1/2" x 4-9/16" x 1-9/16"
IF-DA-NLD: 5-1/8" x 3-7/8" x 1-1/8"
Pg. 2
NDR-LD Instr.
1198bkjd
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
TOLL FREE FAX LINE:
(800) 832-3765
TECHNICAL SUPPORT E-MAIL:
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
Normally Open contacts
are maintained when the
door release button is being
pressed while a station
button is selected.
To convert RY-PA to N/C
(normally closed) contact,
Move one yellow wire from
"NO" to "NC". (Internal
connection, soldering
required.)
To activate
door release,
press button
located above
TALK button.
WIRING DIAGRAM: SYSTEM USED FOR SELECTIVE DOOR RELEASE
NDR-20-LD
+
-
PS-2410A
External
Terminal Block
1
2
~
20
L
Closure for Station #2
Closure for Station #1
BLKYEL
RY-PA
#1
BLK YEL
RY-PA
#2
1
2
3
~
20
E
H
+
-
-
1
-
2
Aiphone IF-DA-NLD Operating instructions
- Category
- Door intercom systems
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Aiphone NEM-30-LD Operating instructions
-
Aiphone PC-359B Operating instructions
-
-
-
-
-
-
Aiphone A83090 User manual
-
-
Other documents
-
Moxa NDR Power Supply Series Quick setup guide
-
-
Altec Lansing LEF-3L User manual
-
Emerson VCIMD-15082 User manual
-
Mean Well NDR-75-12 User manual
-
Eneo NLD-1401 Installation guide
-
Hoymiles HT10 Installation guide
-
Hoymiles HT10 Installation guide
-
GE VIC5211R Installation/Operation Instructions Warranty Information
-
Posiflex HS-2410W \ HS-2410A User manual
