A+ Corporation Avenger 38M Installation & Operation Instructions

Brand: A+ Corporation

Model: Avenger 38M

Type: Installation & Operation Instructions

SCC-38M-InsInstallationOperation_100318

An ISO 9001:2008 certiﬁed company

Manufacturing Contact Information

A+ Corporation, LLC

41041 Black Bayou Rd.

Gonzales, LA 70737

Call for expert product application assistance:

Phone: (225)-644-5255 Website: www.geniefilters.com

Fax: (225)-644-3975 E-mail: sales@geniefilters.com

Safety Warnings

Tools Required

Avenger™ Model 38M

Installation & Operation Instructions

Failure to abide by any of the safety warnings below may result in equipment failure and serious injury or death.

} 



} 

} 

} Four #10 screws for mounting bracket to panel.

} Screwdriver for mounting bracket to panel.

SCC-38M-InsInstallationOperation_100318

An ISO 9001:2008 certiﬁed company



Technical Specications

Dimensions

Back View Side View

PORT D

3.700”

0.355”

1.250”

DIA.

3.256”

0.883”

3.700”

1.876”

2.626”

2.000”

2.625”

4.270”

4.995”

MINIMUM MAINTENANCE CLEARANCE 8.100”

OPTIONAL

MOUNTING

BRACKET

Technical Speciﬁcations

Maximum recommended

membrane ﬂow rate

(For higher ﬂow rates contact the factory)

Outside Diameter: ~ 1.4”

Inside Diameter: ~ 1.0”

Length: ~ 2.5”

Lowest possible pressure consistent with application

Machined parts: 316/316L stainless steel / NACE compliant

All other metal parts: stainless steel / NACE compliant

Sealing material: Fluoroelastomer standard

Membrane: inert

2,000 psig

1/4” female NPT

185˚F (85˚C) for Type 6 membrane

302˚F (150˚C) for Type 7 membrane

1,000 cc/min for Type 6 membrane

3,600 cc/min for Type 7 membrane

*Maximum ﬂow results in approximately 2 psi membrane diﬀerential pressure

Maximum recommended

supply pressure

Port sizes

Number of ports

50 cc

Internal volume

Wetted materials

Maximum pressure rating

Element size

Maximum temperature

35 psig*

*Slowly open the supply pressure so that the minimum diﬀerential

pressure required to shut oﬀ the Liquid Block™ is not met or exceeded.

Maximum Liquid Block™

valve auto-reset pressure

SCC-38M-InsInstallationOperation_100318

An ISO 9001:2008 certiﬁed company



Installation Instructions

Install the mounting bracket onto the Avenger Model 33M or 38M as per the Mounting Bracket Installation Instructions included in A+

Corporation Mounting Bracket Kit P/N 33-509SS for Model 33M or P/N 38-509SS for Model 38M. Aftermarket brackets may be mounted

as per the mounting diagrams below. Mount the Avenger horizontally as shown in the diagram. Lock washers may be used on the lower 10-







Application Drawing

SCC-38M-InsInstallationOperation_100318

An ISO 9001:2008 certiﬁed company



Application Drawing

An ISO 9001:2008 certiﬁed company

Genie,

Avenger,

Liquid Block

and Genie

Membrane Technology

are trademarks or registered

trademarks of A

orporation, LLC. All other referenced trademarks are the property of their respective owners.

Model Numbering & Additional Part Numbers

How to build the model number:

How to build the replacement ﬁlter element number: How to build the replacement membrane kit number:

How to build the replacement o-ring kit number:

Your model number is determined by your speciﬁc needs. Choose options below.

Sealing material 0 = Fluoroelastomer 1 = Perﬂuoroelastomer (other materials available upon request)

Element type 07CFS = 0.1 micron coalescer ﬂuorocarbon SS10 = 10 micron stainless steel

Membrane type 6 = Rejects ALL types of liquids from vapor 7= Rejects ONLY high surface tension liquids

Liquid Block™

Blank = No Liquid Block™

L = Liquid Block™

Mounting bracket accessory Part # 38-509SS (sold separately)

38M

3/2

Sealing material

Element type

Membrane type

Liquid Block™ option

Element type Membrane type

38M

5 0

38M

5 0

Sealing material

Replacement ﬁlter and membrane kits contain 5 each. O-ring replacement kit contains all assembly o-rings.

We cannot recommend speciﬁc sealing materials due to the complex nature of sample stream compositions. Temperature and pressure also may be factors. Unless speciﬁed otherwise, the product

will ship with our standard sealing materials and materials of construction stated in the technical speciﬁcations section of the corresponding Product Sheet.

Please refer to dupontelastomers.com for sealing material recommendations and advice. It is the user’s responsibility to specify the sealing materials of construction for their application.