2. B-K lighting
  3. Junction Box Vertical Louvered

B-K lighting Junction Box Vertical Louvered Installation guide

  • Hello! I am an AI chatbot trained to assist you with the B-K lighting Junction Box Vertical Louvered Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
RELEASE
5-19-16
REFERENCE NUMBER
INS001014
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
TOOLS
NEEDED:
By Others
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
VB™/VBL™
Rectangular Back Box Installation Instructions
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
VB
This set of instructions works for:
VBL
1/8” Allen wrench
Phillips Screwdriver
Waterproof Wire Connectors
Rectangular
Junction Box
With Extension
TECHNOLOGY
with
TECHNOLOGY
Hot Surface
Warning Low Voltage
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
this product.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turnoffpoweratfuseorcircuitbreakerbeforeservice.
• The use of accessory equipment not recommended by the
manufacturerorinstalledcontrarytoinstructionsmaycausean
unsafecondition.Theuseofdamagedcomponentsmaycause
anunsafeconditionandvoidproductwarranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
asthismaycauseanunsafecondition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
aclean,dry,softclothtohandlethelamp.Oilfromskinmay
damagethelampandcauseittorupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, o-rings and sealing surfaces must be kept clean
duringinstallationandservice;failuretodothismaycausean
unsafeconditionandvoidproductwarranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
LightedlampisHOT!
WARNING-ToreducetheriskofFIREORINJURYTOPERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhen
turning on.
Donottouchhotlens,guard,orenclosure(seediagram/
picture).
Keeplampawayfrommaterialsthatmayburn.
Donotouchthelampatanytime.Useasoftcloth.Oil
fromskinmaydamagelamp.
Donotoperatetheluminairefittingwithamissingor
damagedshield.
SAVE THESE INSTRUCTIONS
 ·Suitableforwetlocation·Additionallysuitableformountingwithin4ft.oftheground•TypeNon-IC
IMPORTANT LISTINGS AND CERTIFICATIONS
Pleaserefertothelowvoltagedesignguideatwww.bklighting.com/lvguidebeforeinstallationforproperwireselection.
VERTICAL BACK BOX
Solid State LED
Installation Instructions
Faceplate
AdjustableBracket
Driver
VB - VerticalBrickStar™
VBL - VerticalBrickStar™ Louvered
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
Phase 2 - Finish Installation of Fixture with Remote Transformer
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASE
5-19-16
REFERENCE NUMBER
INS001014
3. Mount faceplate using two (2) #10-24 screws
with 1/8” Allen wrench. Tighten evenly to
compressgasket.Donotovertighten.
2. To aim adjustable bracket loosen the two (2)
Phillip screws attaching the adjustable bracket
tothefaceplate.Aimtodesiredposition.Tighten
two (2) Phillip screws to lock in place when
desired angle is set.
1. Make watertight connections from remote
12V transformer to LED source  leads using
waterproof wire connectors (By Others). See
wiring diagram.
TECHNOLOGY
with
TECHNOLOGY
LINE 12V
Fixture
COM
Remote
Transformer
COM
WIRING DIAGRAM
LED - For use with 12VAC
remote transformer or magnetic
transformers only. B-K Lighting cannot
guarantee performance with third party
manufacturers’ transformers.
VERTICAL BACK BOX
Solid State LED
Installation Instructions
Phase 1 - Rough In
InstallationofBackbox
2. Install Conduit (By Others) to be used with
this product.
5. Connect box to conduit and pull wires for
connections(SeeWiringdiagram).
Additional Info
• PleasefollowNationalandLocalelectricalcodesforyourarea.
• Suitableforthroughwire.
• Suitableforinstallationintocombustiblematerials.
• Ratedfor90°C.
• Orientation of installed back box determines faceplate screw
orientation.
1. Remove canopy and/or fixture from MB2
housing. Ensure unused tapped holes are
pluggedtomaintainseal.Plugsareprovided.
3. To prepare MB2 for mounting, align
mounting brackets on back of box. Brackets
can be aligned to vertical, horizontal or 45°
orientation.  Secure with mounting screw
using screwdriver.
Install back box so that front face is flush
with finished wall or ceiling. Make sure
rectangular back box is plumb before
proceeding.
4. Mount MB2 box to surface using mounting
hardware (Provided) using the mounting
bracketsattachedtobackofMB2box.
Alternative mounting methods may
compromiseintegrityofMB2againstwater
intrusion and will void warranty.
NOTE: Surface conduit is a common entrance
for water if not properly sealed. Seal
connector threads and conduit with a suitable
sealant  (Teflon tape, adhesive, etc.). Sealing
the conduit after knockouts are removed is
required to maintain warranty.
/