Hampton Bay Marlton Owner's manual

Brand: Hampton Bay

Model: Marlton

Category: Household fans

Type: Owner's manual

This manual is also suitable for

YG305-LN

Marlton

52 in Ceiling Fan

Owner’s Manual

Marlton

Ventilador de Techo de 1,32 m

Manual del Propietario

848 883

Marlton by Hampton Bay

52” Marlton

Ceiling Fan by Hampton Bay

Date Purchased

Store Purchased

UL Model No.

Serial No.

Vendor No.

UPC

Thank you for purchasing our ceiling fan. This product has been

manufactured with the highest standards of safety and quality.

Table of Contents

Safety Rules . . . . . . . . . . . . . . . . . . . . 1

Unpacking Your Fan . . . . . . . . . . . . . . 2

Installing Your Fan . . . . . . . . . . . . . . . 3

Installing the Light Kit. . . . . . . . . . . . .10

Operating Your Transmitter . . . . . . . . . 11

Care of Your Fan . . . . . . . . . . . . . . . . 13

Troubleshooting . . . . . . . . . . . . . . . . . 13

Specifications . . . . . . . . . . . . . . . . . . 14

Warranty Information . . . . . . . . . . . . 15

848-883

11289

792145353720

Safety Rules - Read and Save These Instructions

To reduce the risk of electric shock, insure electricity has been turned off at the

circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code

“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation

should be performed by a qualified licensed electrician.

WARNING: To reduce the risk of electrical shock or fire, do not use this fan

with any solid-state fan speed control device. It will permanently damage the

electronic circuitry.

CAUTION: To reduce the risk of personal injury, use only the screws

provided with the outlet box.

The outlet box and support structure must be securely mounted and capable of

reliably supporting a minimum of 35 pounds, Use only UL Listed outlet boxes

marked “FOR FAN SUPPORT”.

The fan must be mounted with a minimum of 7 feet clearance from the trailing

edge of the blades to the floor.

Avoid placing objects in the path of the blades.

To avoid personal injury or damage to the fan and other items, be cautious

when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into outlet box. The wires should be spread

apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of

the outlet box.

All set screws must be checked and retightened where necessary before

installation.

10.

11.

WARNING

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN INSTALLING

THE BRACKETS, BALANCING THE BLADES OR CLEANING THE FAN. DO

NOT INSERT FOREIGN OBJECTS IN – BETWEEN ROTATING FAN BLADES.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR FAN

SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET BOX.

ATTENTION

FAN INCLUDES A 190W LIMITER TO COMPLY WITH THE DEPARTMENT

OF ENERGY 2009 REGULATION. LAMPING THIS PRODUCT OVER 190W

WILL CAUSE THIS FAN TO NOT LIGHT. PLEASE USE BULBS WITH A

TOTAL WATTAGE UNDER THE 190W REGULATION.

Unpacking Your Fan Unpack your fan and check the contents. You should have the following items:

A B

Set of blades (5)

Canopy assembly

Ball/downrod assembly

Coupling cover

Fan motor assembly

Blade support plates (5)

Mounting plate

Light plate

Glass shade

40 Watt candelabra bulbs (3)

Receiver with 6 wire nuts

Transmitter+holder+2 mounting screws

+ 2 plastic plugs

12V MN21/A23 battery

10.

11.

12.

13.

Blade Attachment Hardware

(16 Screws, 16 Fiber Washers)

Electrical Hardware

(3 Plastic Wire Nuts)

Balance Kit

WARNING

DO NOT INSTALL OR USE FAN IF ANY

PART IS DAMAGED OR MISSING.

CALL TOLL FREE 1-877-902-5588.

Installing Your Fan

Figures 1~3 are examples of different ways to

mount the outlet box.

If there isn't an existing UL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 35 lbs). Do not use plastic outlet boxes.

Tools Required

Mounting Options

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN

ONLY TO AN OULET BOX MARKED ACCEPT-

ABLE FOR FAN SUPPORT AND USE THE

MOUNTING SCREWS PROVIDED WITH THE

OULET BOX. OUTLET BOX COMMONLY USED

FOR THE SUPPORT OF LIGHTING FIXTURE

MAY NOT BE ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Outlet Box

Figure 2

Figure 1

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling. The maximum angle

allowable is 18°. If the canopy touches downrod,

remove the decorative canopy bottom cover and

turn the canopy 18° before attaching the canopy to

the mounting plate.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 4 (available at any

Home Depot retailer).

Ceiling

Mounting

Plate

Provide Strong

Support

Recessed

Outlet Box

Figure 3

Figure 4

Phillips screwdriver, straight slot screwdriver, step

ladder and wire cutters.

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly.

Hanging the Fan

WARNING

FAILURE TO PROPERLY INSTALL COTTER PIN

AS NOTED IN STEP 5 COULD RESULT IN FAN

LOOSENING AND POSSIBLY FALLING.

Tighten two set screws at top of the fan motor

collar firmly and evenly. (Fig. 6)

Remove the decorative canopy bottom cover

from the canopy by turning the cover counter

clockwise. (Figure 5)

Remove the mounting bracket from the canopy

by removing the 1 of 2 screws from the bottom

of the mounting bracket and loosening the

other one a half turn from the screw head.

Next, turn the canopy counter clockwise to

removing the canopy cover form the canopy.

(Figure 5)

Remove the clevis pin, cotter pin and set

screws from the top of the motor assembly.

(Figure 6)

NOTE: If a longer downrod is needed, take out

the screw located in the hanger ball, lower the

hanger ball and remove the pin, remove all 3

pieces from the downrod and assemble them

onto the new longer downrod before

proceeding step 4. (The longer downrod is

available at any Home Depot store)

Route wires exiting from the top of the fan

motor through the coupling cover, canopy

cover, canopy and then through the ball/

downrod. (Figure 6)

Align the holes at the bottom of the downrod

with the holes in the coupling on top of the

motor housing (Figure 6). Carefully insert the

clevis pin through the holes in the collar and

downrod. Be careful not to jam the clevis pin

against the wiring inside the downrod. Insert

the cotter pin through the hole near the end of

the clevis pin until it snaps into its locked

position, as noted in the circle inset of Fig. 6.

Figure 5

Figure 6

Motor Wires

Ball/Downrod

Assembly

Ceiling Canopy

Canopy Bottom

Cover

Pin in Locked

Positioon

Motor Collar

Coupling

Cover

Tighten Screw

Firmly

Cotter Pin

Clevis Pin

Ceiling

Mounting

Bracket

Ceiling Canopy

Canopy Bottom

Cover

Installing Fan to

the Electrical Box

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR OTHER PERSONAL INJURY.

MOUNT FAN ONLY TO AN OUTLET BOX OR

SUPPORTING SYSTEM MARKED ACCEPTABLE

FOR FAN SUPPORT AND USE THE MOUNTING

SCREWS PROVIDED WITH THE OUTLET BOX.

Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket as

shown in Figure 7.

Install the ceiling mounting bracket on the

outlet box with the screws and washers

provided with your outlet box (Figure 7).

Security tighten the two mounting screws.

Carefully lift the fan assembly up to the ceiling

mounting bracket and seat the hanger ball in the

mounting bracket socket. Make sure the tab on

the mounting bracket socket is properly seated

in the groove in the hanger ball (Figure 8). This

will help to balance the ceiling fan.

Figure 8

Groove

Tab

Figure 7

WARNING

THE TAB IN THE RING MUST REST IN THE

GROOVE OF THE HANGER BALL AS FIGURE 7.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

UL Listed Outlet Box

Ceiling Mounting

Bracket

120V

Wires

Mounting

Screws (Supplied

with Electrical Box)

Tab

Making the Electrical

Connections

WARNING

TO AVOID POSSIBLE ELECTRICAL SHOCK, BE

SURE ELECTRICITY IS TURNED OFF AT THE

MAIN FUSE BOX BEFORE WIRING.

(Figure 11) Motor to receiver electrical connec-

tions: Connect the black wire from the fan to

black wire marked "TO MOTOR L". Connect

the white wire from the fan to the white wire

marked "TO MOTOR N" from the receiver.

Connect the blue wire from the fan to the blue

wire marked "For Light" from the receiver.

Secure the wire connections with the plastic

wire connecting nuts provided.

(Figure 11) Receiver to house supply wires

electrical connections: Connect the black (hot)

wire from the ceiling to the black wire marked

"AC in L" from he receiver. Connect the white

(neutral) wire from the ceiling to the white wire

marked "AC in N" from the receiver. Secure

the wire connections with the plastic wire

connecting nuts provided.

(Figure 11) If your outlet box has a ground

wire (green or bare copper) connect it to the fan

ground wires; otherwise connect the hanging

bracket ground wire to the mounting bracket.

Secure the wire connection with a plastic nut

provided. After connecting the wires spread

them apart so that the green and white wires are

on one side of the outlet box and black and blue

wires are on the other side. Carefully tuck the

wire connections up into the outlet box.

Insert the receiver into the mounting bracket

with the flat side of the receiver facing the

ceiling as Figure 10.

If you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan to your

household wiring. Use the wire nuts supplied with

your fan. Secure the wire nuts with electrical tape.

Make sure there are no loose strands or

connections.

This remote control unit is equipped with 16 code

combinations to prevent possible interference

from or to other remote units. The frequency

switches on your receiver and transmitter have

been preset at the factory. Please recheck to make

sure the switches on the transmitter and the

receiver are set to the same position, any

combination of settings willoperate the fan as long

as the transmitterand receiver are set to the same

position (Figure 9).

Figure 9

Figure 10

Receiver

Ceiling

Mounting

Bracket

Frequency Switch

CAUTION

DO NOT USE WITH WALL LIGHT DIMMER

SWITCH.

NOTE

FAN MUST BE INSTALLED AT A MAXIMUM

DISTANCE OF 20 FEET FROM THE TRANSMIT-

TING UNIT FOR PROPER SIGNAL TRANSMIS-

SION BETWEEN THE TRANSMITTING UNIT

AND THE FAN'S RECEIVING UNIT.

Figure 12

SUPPLY CIRCUIT

Figure 11

WHITE

BLACK

BLUE

Ground

Conductor

Outlet Box

Green

Ground

Lead

GREEN

Ground to

Downrod

BLACK BLACK

BLUE

WHITE

WARNING

MAKE SURE THE TAB ON THE HANGER

BRACKET PROPERLY SITS IN THE GROOVE

IN THE HANGER BALL BEFORE ATTACH-

ING THE CANOPY TO THE BRACKET BY

TURNING THE HOUSING UNTIL IT DROPS

INTO PLACE.

Tuck connections neatly into ceiling outlet

box.

Slide the canopy up to mounting bracket and

place the key hole on the canopy over the

screw on the mounting bracket, turn canopy

until it locks in place at the narrow section of

the key holes. (Fig. 12)

Align the circular hole on canopy with the

remaining hole on the mounting bracket,

secure by tightening the two set screws. Note:

Adjust the canopy screws as necessary until the

canopy and canopy cover are snug.

Finishing the Fan

Installation

WARNING

CHECK TO SEE THAT ALL CONNECTIONS ARE

TIGHT, INCLUDING GROUND, AND THAT NO

BARE WIRE IS VISIBLE AT THE WIRE NUTS.

EXCEPT FOR THE GROUND WIRE.

WARNING

ELECTRICAL DIAGRAMS ARE FOR REFER-

ENCE ONLY. OPTIONAL USE OF ANY LIGHT

KIT SHELL BE UL LISTED AND MARKED

SUITABLE FOR USE WITH THIS FAN.

Outlet Box

Ceiling

Mounting

Bracket

Screws

Canopy

Bottom

Cover

Attaching the Fan Blades WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADES WHILE INSTALL-

ING, BALANCING THE BLADES, OR CLEANING

THE FAN. DO NO INSERT FOREIGN OBJECTS

BETWEEN ROTATING FAN BLADES.

Figure 13

Insert the blade through the blade slot in the

decorative housing. Align the holes in blade

and blade arm, place the blade support plate on

blade as showing in Figure 13, making sure the

holes are also aligned and secure with fiber

washers and screws provided.

Repeat process with other blades.

Fiber Washers

Blade Support

Plates

Blades

Screws

Slot

Blade Balancing

Check that all blade and blade bracket screws

are secure.

Most fan wobble problems are caused when

blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of

one of the blades. Measure from a point on the

center of each blade to the point on the ceiling.

Measure this distance as shown in Figure 14.

Rotate the fan until the next blade is positioned

for measurement. Repeat for each blade.

Measurements deviation should be within 1/8˝.

Run the fan for 10 Minutes.

Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

The following procedure should correct most fan

wobble. Check after each step.

Figure 14

Touching Ceiling

Mounting Ring

Mounting Plate

Screws

Figure 15

Attaching the Mounting

Plate

Remove 1 of 3 screws from the mounting ring

and loosen the other 2 screws. (Do not remove)

Place the key holes on the mounting plate over

the 2 screws previously loosened from the

mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 15)

Installing the

Light Kit

Install the glass shade assembly to the mount-

ing plate with screws provided. (Fig. 16)

Restore power and your light kit is ready for

operation.

NOTE

LIGHT BULBS HAVE NO WARRANTY; CAN BE

PURCHASED AT ANY HOME DEPOT STORE.

While holding the light plate under your fan,

locate two single white and blue wires in the

switch housing labeled FOR LIGHT. Make the

polarized plug connections:

- White to white

- Blue to black

Carefully push all wires back into the mount-

ing plate, then install the light plate onto the

mounting plate with 3 screws provided. Be

sure to tighten all screws. (Fig. 16)

Install 3 x 40W candelabra bulbs (included).

(Fig. 16)

CAUTION

BEFORE STARTING INSTALLATION, DISCON-

NECT THE POWER BY TURNING OFF THE

CIRCUIT BREAKER OR REMOVING THE FUSE

AT FUSE BOX. TURNING POWER OFF USING

THE FAN SWITCH IS NOT SUFFICIENT TO

PREVENT ELECTRIC SHOCK.

Figure 16

Screws

Glass Shade

Bulbs

Wire Connectors

Mounting

Plate

Light Plate

1111

Installing the Battery:

"HI, MED, LOW" buttons:

These three buttons are used to set the fan

speed as follows:

LOW=Low speed,

MED= Medium speed

HI=High speed

"OFF" button:

This button turns the fan off.

The " " button turns the light ON or OFF

and also controls the brightness setting. Press

and release the button to turn the light ON or

OFF. Press and hold the button to set the

desired brightness. The light button has an

auto-resume, it will stay at the same brightness

as the last time it was turned off.

Install 12V MN21/A23 battery (included), to

prevent damage to transmitter, remove the battery

if not used for long periods (Figure 17).

Restore power to the ceiling fan and test for

proper operation.

Figure 17

Operating Your Transmitter

Figure 18

Speed settings for warm or cool weather depend

on factors such as the room size, ceiling height,

number of fans, and so on.

The Reverse switch is located on the top of motor

housing. Slide the switch to the Left for warm

weather operation. Slide the switch to the Right for

cool weather operation.

Warm weather - (Counter-Clockwise direction)

A downward air flow creates a cooling effect.(Fig.

19) This allows you to set your air conditioner on

a higher setting without affecting your comfort.

Cool weather - (Clockwise direction) An upward

airflow moves warm air off the ceiling area. (Fig.

20) This allows you to set your heating unit on a

lower setting without affecting your comfort.

NOTE

DO NOT OPERATE REVERSING SWITCH

WHILE FAN BLADES ARE IN MOTION. FAN

MUST BE TURNED OFF AND BLADES STOPPED

BEFORE REVERSING BLADE DIRECTION.

Figure 19

Figure 20

WARNING

MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX

BEFORE YOU ATTEMPY ANY REPAIRS. REFER TO THE SECTION,

“MAKING ELECTRICAL CONNECTIONS”.

Because of the fan's natural movement, some

connections may become loose. Check the

support connections, brackets, and blade

attachments twice a year. Make sure they are

secure. (It is not necessary to remove fan from

ceiling.)

Clean your fan periodically to help maintain its

new appearance over the years. Do not use

water when cleaning. Use only a soft brush or

lint-free cloth to avoid scratching the finish.

The plating is sealed with a lacquer to

minimize discoloration or tarnishing. Do not

use water when cleaning. This could damage

the motor, or the wood, or possibly cause an

electrical shock.

You can apply a light coat of furniture polish to

the wood blades for additional protection and

enhanced beauty. Cover small scratches with a

light application of shoe polish.

There is no need to oil your fan. The motor has

permanently lubricated sealed ball bearings.

Here are some suggestions to help you maintain

your fan.

Check main and branch circuit fuses or breakers.

Check line wire connections to the fan and switch wire connections in

the switch housing.

Check to make sure the dip switches from the transmitter and receiver

are set to the same frequency.

Make sure all motor housing screws are snug.

Make sure the screws that attach the fan blade bracket to the motor hub

is tight.

Make sure wire nut connections are not rattling against each other or

the interior wall of the switch housing.

Allow a 24-hour "breaking-in" period. Most noises associated with a

new fan disappear during this time.

If using an optional light kit, make sure the screws securing the

glassware are tight. Check that the light bulb is also secure.

Make sure the upper canopy is a short distance from the ceiling. It

should not touch the ceiling.

Make sure your ceiling box is secure and rubber isolator pads are used

between mounting bracket and outlet box.

Do not connect the fan with a wall mounted variable speed control(s).

Make sure the dip switches are set correctly.

Fan will not start

Fan sounds noisy

Remote control

Care of Your Fan Troubleshooting

PROBLEM SOLUTION

Specifications

FAN SIZE SPEED VOLTS AMPS WATTS RPM CFM N.W. G.W. C.F.

52” 120 10.2 kgs

(22.44 lbs)

11.4 kgs

(25.08 lbs) 2.33’

LOW

MED.

HIGH

0.34

0.46

0.57

110

166

2319.61

3584.98

5568.88

These are approximate measures. They do not include Amps and Wattage used by the light kit .

The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time

of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.

Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from

defects in workmanship and material at the time of shipment from the factory for a period of one year after the

date of purchase by the original purchaser. We agree to correct such defects without charge or at our option

replace with a comparable or superior model if the product is returned to Hampton Bay. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the

product are your responsibility. Damage to any part such as by accident or misuse or improper installation or

by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this

warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling.

Brass finishes of this type give their longest useful life when protected from varying weather conditions. A

certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by

unauthorized persons shall render the warranty invalid. There is no other express warranty. Hampton Bay

hereby disclaims any and all warranties, including but not limited to. Those of merchantability and fitness for

a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be

disclaimed is limited to the time period as specified in the express warranty. Some states do not allow

limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer

shall not be liable for incidental, consequential, or special damages arising out of or in connection with product

use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of

incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty

gives specific legal rights, and you may also have other rights which vary from state to state. This warranty

supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must

be paid by the customer.

Hampton Bay Lifetime Limited Warranty

(lifetime warranty on motor)

You must present a copy of the original

purchase receipt to obtain warranty

service.

Ceiling Fan Parts & Service Department

2919 E. Philadelphia Street

Ontario, CA 91761

U.S.A.

Attach receipt here for easy

location

Hampton Bay Marlton Owner's manual

Brand: Hampton Bay

Model: Marlton

Category: Household fans

Type: Owner's manual

This manual is also suitable for

YG305-LN

Download PDF

report

Hampton Bay Marlton Owner's manual

This manual is also suitable for

Hampton Bay Marlton Owner's manual

Related papers

Other documents