Hampton Bay YG092-VPW User guide

Brand: Hampton Bay

Model: YG092-VPW

Category: Household fans

Type: User guide

Hampton Bay YG092-VPW is top-quality ceiling fan that is designed to satisfy the needs of even the most demanding user. The fan comes with a variety of features that make it a worthwhile investment. These features include 4-speed control which ensures you will always have the right airflow. Additionally, the fan has a reversible airflow, which can be used to keep you cool in the summer and warm in the winter. The Hampton Bay YG092-VPW also features a dimmable integrated LED light kit, so you can control the brightness of the light to create the perfect ambiance.

Preston

in Ceiling Fan

Owner’s Manual

Preston

Ventilador de Techo de 1,32

Manual del Propietario

283 528

52” Preston

Ceiling Fan by Hampton Bay

Date Purchased

Store Purchased

UL Model No.

Serial No.

Vendor No.

UPC

Thank you for purchasing our ceiling fan. This product has been

manufactured with the highest standards of safety and quality.

Table of Contents

Safety Rules . . . . . . . . . . . . . . . . . . . . 1

Unpacking Your Fan . . . . . . . . . . . . . . 2

Installing Your Fan . . . . . . . . . . . . . . . 3

Installing the Light Kit. . . . . . . . . . . . . 10

Operating Your Transmitter . . . . . . . . . . . 11

Care of Your Fan . . . . . . . . . . . . . . . . 13

Troubleshooting . . . . . . . . . . . . . . . . . 13

Specifications . . . . . . . . . . . . . . . . . . 14

Warranty Information . . . . . . . . . . . . 15

283-528

219032

792145353133

Safety Rules - Read and Save These Instructions

To reduce the risk of electric shock, insure electricity has been turned off

at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code

“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation

should be performed by a qualified licensed electrician.

WARNING: To reduce the risk of electrical shock or fire, do not use this

fan with any solid-state fan speed control device. It will permanently

damage the electronic circuitry.

CAUTION: To reduce the risk of personal injury, use only the screws

provided with the outlet box.

The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 pounds. Use only UL

Listed outlet boxes marked “FOR FAN SUPPORT”.

The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge of the blades to the floor.

Avoid placing objects in path of the blades.

To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box and ungrounded conductor on the

other side of the outlet box.

All set screws must be checked and retightened where necessary before

installation.

10.

11.

WARNING

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN INSTALLING

THE BRACKETS, BALANCING THE BLADES OR CLEANING THE FAN.

DO NOT INSERT FOREIGN OBJECTS IN – BETWEEN ROTATING FAN

BLADES.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY,

MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT

WITH THE SCREWS PROVIDED WITH THE OUTLET BOX.

ATTENTION

FAN INCLUDES A 190W LIMITER TO COMPLY WITH THE DEPARTMENT

OF ENERGY 2009 REGULATION. LAMPING THIS PRODUCT OVER 190W

WILL CAUSE THIS FAN TO NOT LIGHT. PLEASE USE BULBS WITH A

TOTAL WATTAGE UNDER THE 190W REGULATION.

Unpacking Your Fan

Unpack your fan and check the contents. You should have the following items:

Set of blades (5)

Canopy assembly

Ball/downrod assembly (1)

& extra downrod (1)

Coupling cover

Fan motor assembly

Set of blade arms (5)

Mounting plate

Switch housing

Light kit

Glass shades (3)

Receiver+6 wire nuts

Transmitter+holder+2 mounting screws

Extra plastic plug

60 Watt candelabra bulbs (3)

10.

11.

12.

13.

14.

Blade Attachment Hardware

(16 Screws with Fiber Washers)

Electrical Hardware

(3 Plastic Wire Nuts)

Balancing Kit

WARNING

DO NOT INSTALL OR USE FAN IF ANY

PART IS DAMAGED OR MISSING.

CALL TOLL FREE 1-877-902-5588.

LIGHT / DIMMER

MED

FAN OFF

Installing Your Fan

Figures 1~3 are examples of different ways to

mount the outlet box.

If there isn't an existing UL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 35 lbs). Do not use plastic outlet boxes.

Tools Required

Mounting Options

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN

ONLY TO AN OULET BOX MARKED ACCEPT-

ABLE FOR FAN SUPPORT AND USE THE

MOUNTING SCREWS PROVIDED WITH THE

OULET BOX. OUTLET BOX COMMONLY USED

FOR THE SUPPORT OF LIGHTING FIXTURE

MAY NOT BE ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Outlet Box

Figure 2

Figure 1

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling. The maximum angle

allowable is 29

. If the canopy touches downrod,

remove the decorative canopy bottom cover and

turn the canopy 180

before attaching the canopy

to the mounting plate.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 4 (available at any

Home Depot store).

Ceiling

Mounting

Plate

Provide Strong

Support

Recessed

Outlet Box

Figure 3

Figure 4

Phillips screwdriver, straight slot screwdriver, step

ladder and wire cutters.

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly.

Hanging the Fan

WARNING

FAILURE TO PROPERLY INSTALL COTTER PIN

AS NOTED IN STEP 5 COULD RESULT IN FAN

LOOSENING AND POSSIBLY FALLING.

Tighten two set screws at top of the fan motor

collar firmly and evenly. (Fig. 6)

Remove the decorative canopy bottom cover

from the canopy by turning the cover counter

clockwise. (Figure 5)

Remove the mounting bracket from the canopy

by loosening the two screws on the bottom of

the mounting bracket a half turn from the screw

head and turning the canopy counter

clockwise. (Figure 5)

Remove the clevis pin, cotter pin and set

screws from the top of the motor assembly.

(Figure 6)

Route wires exiting from the top of the fan

motor through the coupling cover, canopy

cover, canopy and then through the ball/

downrod. (Figure 6)

Align the holes at the bottom of the downrod

with the holes in the coupling on top of the

motor housing (Figure 6). Carefully insert the

clevis pin through the holes in the collar and

downrod. Be careful not to jam the clevis pin

against the wiring inside the downrod. Insert

the cotter pin through the hole near the end of

the clevis pin until it snaps into its locked

position, as noted in the circle inset of Fig. 6.

Figure 5

Ceiling

Mounting

Bracket

Ceiling Canopy

Canopy Bottom

Cover

Figure 6

Motor Wires

Ball/Downrod

Assembly

Ceiling Canopy

Canopy Bottom

Cover

Pin in Locked

Positioon

Motor Collar

Coupling

Cover

Tighten Screw

Firmly

Cotter Pin

Clevis Pin

WARNING

THE TAB IN THE RING MUST REST IN THE

GROOVE OF THE HANGER BALL AS FIGURE 8.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

Installing Fan to

the Electrical Box

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR OTHER PERSONAL INJURY. MOUNT

FAN ONLY TO AN OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN

SUPPORT AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX.

Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket as

shown in Figure 7.

Install the ceiling mounting bracket on the

outlet box with the screws and washers

provided with your outlet box (Figure 7).

Security tighten the two mounting screws.

Carefully lift the fan assembly up to the ceiling

mounting bracket and seat the hanger ball in the

mounting bracket socket. Make sure the tab on

the mounting bracket socket is properly seated

in the groove in the hanger ball (Figure 8). This

will help to balance the ceiling fan.

Changing the Downrod

(Optional)

NOTE: Your fan comes with a 5" downrod

attached to the hanger ball. In addition you have

been provided with a 7" downrod to use if desired.

If you choose to use the 7" downrod, perform the

following steps:

Remove the hanger ball from the 5" downrod

by loosening the set screw at the top of the

downrod which holds the hanger ball to the

downrod.

Slide the hanger ball down the downrod and

remove the support pin.

Insert the support pin in the holes at the top of

the 7" downrod and slide the hanger ball up the

7" downrod. Make sure the support pin is

properly seated in the grooves in the top of the

hanger ball.

Tighten the set screw firmly.

Figure 7

UL Listed Outlet Box

Ceiling Mounting

Bracket

120V

Wires

Mounting

Screws

(Supplied

with Electrical Box)

Tab

Figure 8

Groove

Tab

Making the Electrical

Connections

WARNING

TO AVOID POSSIBLE ELECTRICAL SHOCK, BE

SURE ELECTRICITY IS TURNED OFF AT THE

MAIN FUSE BOX BEFORE WIRING.

If you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

This remote control unit is equipped with 16 code

combinations to prevent possible interference

from or to other remote units. The frequency

switches on your receiver and transmitter have

been preset at the factory. Please recheck to make

sure the switches on the transmitter and the

receiver are set to the same position, any

combination of settings will operate the fan as

long as the transmitter and receiver are set to the

same position. (Figure 9).

Insert the receiver into the mounting bracket

with the flat side of the receiver facing the

ceiling as Figure 10.

receiver. Secure the wire connections with the

plastic wire connecting nuts provided.

(Figure 11) Receiver to house supply wires

electrical connections: Connect the black (hot)

wire from the ceiling to the black wire marked

"AC in L" from he receiver. Connect the white

(neutral) wire from the ceiling to the white wire

marked "AC in N" from the receiver. Secure

the wire connections with the plastic wire

connecting nuts provided.

(Figure 11) If your outlet box has a ground

wire (green or bare copper) connect it to the fan

ground wires; otherwise connect the hanging

bracket ground wire to the mounting bracket.

Secure the wire connection with a plastic nut

provided. After connecting the wires spread

them apart so that the green and white wires are

on one side of the outlet box and black and blue

wires are on the other side. Carefully tuck the

wire connections up into the outlet box.

(Fig. 11) Motor to receiver electrical

connections: Connect the black wire from the

fan to black wire marked "TO MOTOR L".

Connect the white wire from the fan to the

white wire marked "TO MOTOR N" from the

receiver. Connect the blue wire from the fan to

the blue wire marked "For Light" from the

Figure 10

Receiver

Ceiling

Mounting

Bracket

Figure 9

Frequency Switch

CAUTION

DO NOT USE WITH WALL LIGHT DIMMER

SWITCH.

NOTE

FAN MUST BE INSTALLED AT A MAXIMUM

DISTANCE OF 20 FEET FROM THE TRANSMIT-

TING UNIT FOR PROPER SIGNAL TRANSMIS-

SION BETWEEN THE TRANSMITTING UNIT

AND THE FAN'S RECEIVING UNIT.

WARNING

MAKE SURE THE TAB ON THE HANGING

BRACKET PROPERLY SITS IN THE GROOVE IN

THE HANGER BALL BEFORE ATTACHING THE

CANOPY TO THE BRACKET BY TURNING THE

HOUSING UNTIL IT DROPS INTO PLACE.

Tuck connections neatly into ceiling outlet

box.

Slide the canopy up to ceiling and over the 2

screws on the hanger bracket. Rotate canopy

clockwise. Next, while holding the canopy

with one hand, slide the canopy cover over the

screws and rotate clockwise until tight. Note:

adjust the canopy screws as necessary until the

canopy and canopy cover are snug. (Fig. 12)

Finishing the Fan

Installation

WARNING

CHECK TO SEE THAT ALL CONNECTIONS ARE

TIGHT, INCLUDING GROUND, AND THAT NO

BARE WIRE IS VISIBLE AT THE WIRE NUTS.

EXCEPT FOR THE GROUND WIRE.

WARNING

ELECTRICAL DIAGRAMS ARE FOR

REFERENCE ONLY. OPTIONAL USE OF ANY

LIGHT KIT SHALL BE UL LISTED AND

MARKED SUITABLE FOR USE WITH THIS FAN.

SUPPLY CIRCUIT

Figure 11

WHITE

BLACK

BLUE

Ground

Conductor

Outlet Box

Green

Ground

Lead

GREEN

Ground to

Downrod

BLACK

BLUE

WHITE

Figure 12

Outlet Box

Ceiling

Mounting

Bracket

Screws

Canopy

Bottom

Cover

Attaching the Fan Blades

Attach blades to blade arm using the screws

with fiber washers provided (Fig. 14). Start a

screw into the blade arm, do not tighten.

Repeat for the 2 remaining screws and

washers.

Tighten each screw securely starting with the

center screw. Make sure the blade is straight.

Repeat steps for the remaining blades.

Fasten the blade assemblies to the motor

housing by lining up the slots of the blade arms

with the tabs on the motor housing, then

tighten the two screws and washers already

installed in the blade arms (Figure 15).

CAUTION

MOTOR IS SHIPPED WITH RUBBER PACKING

MOUNTS TO PREVENT MOVEMENT DURING

TRANSPORTATION. REMOVE 5 RUBBER

PACKING MOUNTS FROM FAN MOTOR ASSEM-

BLY AND DISCARD PRIOR TO ATTACHING

BLADE ARMS. (FIG. 13)

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO

NOT BEND THE BLADE ARMS WHILE INSTALL-

ING, BALANCING THE BLADES, OR CLEANING

THE FAN. DO NO INSERT FOREIGN OBJECTS

BETWEEN ROTATING FAN BLADES.

Figure 15

Figure 13

Figure 14

Screws

Rubber Packing Mounts

Motor

Blade Arm

Slot

Tab

Blade Arm

Blade

Screws

with Fiber

Washer

Blade Balancing

Check that all blade and blade bracket screws

are secure.

Most fan wobble problems are caused when

blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of

one of the blades. Measure from a point on the

center of each blade to the point on the ceiling.

Measure this distance as shown in Figure 16.

Rotate the fan until the next blade is positioned

for measurement. Repeat for each blade.

Measurements deviation should be within 1/8˝.

Run the fan for 10 Minutes.

Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

The following procedure should correct most fan

wobble. Check after each step.

Figure 16

Touching Ceiling

Installing the Mounting

Plate

Remove 1 of the 3 screws from the mounting

ring and loosen the other 2 screws. (Do not

remove)

Place the key holes on the mounting plate over

the 2 screws previously loosened from the

mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 17)

Figure 17

Mounting Plate

Mounting Ring

Screws

Installing the Light Kit

Attach the light kit to the switch housing by

feeding the light kit wires (black and white)

through the hole of switch housing and then

screw it onto the switch housing by nut & lock

washer. Be sure it is tight enough to prevent

light kit from vibrating loose. (Fig. 18)

Locate two single white and blue wires in the

switch housing labeled FOR LIGHT.

Make the polarized plug connections:

- White to white

- Blue to black

While holding the light kit assembly under

your fan, snap together the wire connection

plugs.

Carefully push all wires back into the switch

housing, then install the light kit assembly onto

the mounting plate with 4 screws provided. Be

sure to tighten all screws. (Fig. 19)

Remove the lock ring from the socket by

turning the lock ring counter-clockwise Until it

unlocks. Insert the glass into the glass holder

and turn the lock ring clockwise to tighten the

glass. Repeat for the remaining glass. (Fig. 19)

Install 3 x 60W candelabra bulbs (included).

Restore power and your light kit is ready for

operation.

NOTE

LIGHT BULBS HAVE NO WARRANTY; CAN BE

PURCHASED AT ANY HOME DEPOT STORE.

CAUTION

BEFORE STARTING INSTALLATION, DISCON-

NECT THE POWER BY TURNING OFF THE

CIRCUIT BREAKER OR REMOVING THE FUSE

AT FUSE BOX. TURNING POWER OFF USING

THE FAN SWITCH IS NOT SUFFICIENT TO

PREVENT ELECTRIC SHOCK.

Figure 18

Figure 19

Screws

Lock Ring

Bulbs

Light Kit

Assembly

Glass Shade

Wire Connection

Plugs

Glass Holder

Nut

Lock Washer

Switch

Housing

Light Kit

1111

Installing the Battery:

"HI, MED, LO" buttons:

These three buttons are used to set the fan

speed as follows:

LO=Low speed,

MED= Medium speed

HI=High speed

"FAN OFF" button:

This button turns the fan off.

The "LIGHT/DIMMER" button turns the

light ON or OFF and also controls the bright-

ness setting. Press and release the button to

turn the light ON or OFF. Press and hold the

button to set the desired brightness. The light

key has an auto-resume, it will stay at the same

brightness as the last time it was turned off.

Install 9 volt battery (not included), to prevent

damage to transmitter, remove the battery if not

used for long periods (Figure 20).

Restore power to the ceiling fan and test for

proper operation.

Figure 20

Operating Your Transmitter

Figure 21

LIGHT / DIMMER

MED

FAN OFF

Speed settings for warm or cool weather depend

on factors such as the room size, ceiling height,

number of fans, etc.

The Reverse switch is located on the switch

housing. Slide the switch to the Left for warm

weather operation. Slide the switch to the Right for

cool weather operation.

Warm weather - (Counter-Clockwise direction)

A downward air flow creates a cooling effect.(Fig.

22) This allows you to set your air conditioner on

a higher setting without affecting your comfort.

Cool weather - (Clockwise direction) An upward

airflow moves warm air off the ceiling area. (Fig.

23) This allows you to set your heating unit on a

lower setting without affecting your comfort.

NOTE

WAIT FOR FAN TO STOP BEFORE CHANGING

THE SETTING OF THE SLIDE SWITCH.

Figure 22

Figure 23

WARNING

MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX

BEFORE YOU ATTEMPY ANY REPAIRS. REFER TO THE SECTION,

“MAKING ELECTRICAL CONNECTIONS”.

Because of the fan's natural movement, some

connections may become loose. Check the

support connections, brackets, and blade

attachments twice a year. Make sure they are

secure. (It is not necessary to remove fan from

ceiling.)

Clean your fan periodically to help maintain its

new appearance over the years. Do not use

water when cleaning. Use only a soft brush or

lint-free cloth to avoid scratching the finish.

The plating is sealed with a lacquer to

minimize discoloration or tarnishing. Do not

use water when cleaning. This could damage

the motor, or the wood, or possibly cause an

electrical shock.

You can apply a light coat of furniture polish to

the wood blades for additional protection and

enhanced beauty. Cover small scratches with a

light application of shoe polish.

There is no need to oil your fan. The motor has

permanently lubricated sealed ball bearings.

Here are some suggestions to help you maintain

your fan.

Check main and branch circuit fuses or breakers.

Check line wire connections to the fan and switch wire connections in

the switch housing.

Check to make sure the dip switches from the transmitter and receiver

are set to the same frequency.

Make sure all motor housing screws are snug.

Make sure the screws that attach the fan blade bracket to the motor hub

is tight.

Make sure wire nut connections are not rattling against each other or

the interior wall of the switch housing.

Allow a 24-hour "breaking-in" period. Most noises associated with a

new fan disappear during this time.

If using ceiling fan light kit, make sure the screws securing the

glassware are tight. Check that the light bulb is also secure.

Make sure there is a short distance from the ceiling to the canopy. It

should not touch the ceiling.

Make sure your ceiling box is secure and rubber isolator pads are used

between mounting bracket and outlet box.

This unit is equipped with a wattage limiting device. Lamping in excess

of 190 watts will disable your ceiling fan's light kit. To reset your light

kit you must turn the power off and relamp, keeping the wattage under

190 watts. Restore power to your ceiling fan and continue normal

operation.

Do not connect the fan with a wall mounted variable speed control(s).

Make sure the dip switches are set correctly.

Fan will not start

Fan sounds noisy

Lights shut off and

will not come back

on.

Remote control

Care of Your Fan Troubleshooting

PROBLEM SOLUTION

Specifications

FAN SIZE SPEED VOLTS AMPS WATTS RPM CFM N.W. G.W. C.F.

52” 120

14.88 kgs

(32.74 lbs)

16.51 kgs

(36.32 lbs)

3.05’

LOW

MED.

HIGH

0.35

0.54

0.68

115

165

1200

3850

6500

These are approximate measures. They do not include Amps and Wattage used by the light kit.

The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time

of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.

Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from

defects in workmanship and material at the time of shipment from the factory for a period of one year after the

date of purchase by the original purchaser. We agree to correct such defects without charge or at our option

replace with a comparable or superior model if the product is returned to Hampton Bay. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the

product are your responsibility. Damage to any part such as by accident or misuse or improper installation or

by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this

warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling.

Brass finishes of this type give their longest useful life when protected from varying weather conditions. A

certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by

unauthorized persons shall render the warranty invalid. There is no other express warranty. Hampton Bay

hereby disclaims any and all warranties, including but not limited to. Those of merchantability and fitness for

a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be

disclaimed is limited to the time period as specified in the express warranty. Some states do not allow

limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer

shall not be liable for incidental, consequential, or special damages arising out of or in connection with product

use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of

incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty

gives specific legal rights, and you may also have other rights which vary from state to state. This warranty

supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must

be paid by the customer.

Lifetime Limited Warranty

(lifetime warranty on motor)

You must present a copy of the original

purchase receipt to obtain warranty

service.

Ceiling Fan Parts & Service Department

2919 E. Philadelphia Street

Ontario, Ca 91761

Attach receipt here for easy

location

Hampton Bay YG092-VPW User guide

Brand: Hampton Bay

Model: YG092-VPW

Category: Household fans

Type: User guide

Download PDF

report

Hampton Bay YG092-VPW User guide

Hampton Bay YG092-VPW User guide

Related papers

Other documents