Herman Miller My Studio Environments Product Instructions

Type
Product Instructions
Tools Required:
Power Driver
Side Wall Electrical Harness
IMPORTANT: Save these instructions for layout changes.
Parts Included:
#2 Phillips Bit
#8-15 X 1/2”
Lock Washer
#10-12 X 3/4”
Screw (5)
Screw (5)
1/4-20 X 1
Machine Screw
I
HTube Clamp
E F
K
1/4-20
J
Conduit End
GTube
Conduit
LChannelHex Nut
Hardware Pack
180 Degree Harness cover 90 Degree Harness Cover
A
DCable Trough
BC
WARNING
Disconnect electrical power before installation. Failure to do
so can cause electrical shock and personal injury.
!
7/16 Wrench
1
1. Remove only Port Covers for ports being used.
Port Cover
3. Store Port Covers in safe place for future use.
A
NOTICE
Install Power/Data Distributor before in
stalling Electrical
Cladding on both sides of Center Wall.
Electrical Rating:
120/208V, 120/240V 20A (15A CSA)
15A When Powered with Energy Manager (PT 130, PT 131)
1. A 20A rated circuit can supply a maximum of 13
receptacles at 15 A.
2. A 15A rated circuit can supply a maximum of 10
receptacles rated at 15A. Receptacles rated at
20A are not allowed.
Chassis Cover
Clips (2)
2. If clips are required, remove from port cover and
attach to Chassis Cover.
2
1. Install Receptacles onto Electrical
3
Harnesses.
Receptacle
Electrical Harness
1. Remove Side Cover by pulling out on
1. Assemble Side Cover.
4
WARNING
!
All electrical connections mu
st be fully engaged and locked.
Loose connections can cause fire and /or electrical shock.
sides of Chassis Cover.
Chassis Cover
Side Cover
1. From under Work Surface, install
Work Surface
Power/Data
6
F
Power/Data Distributor onto Work
Surface with (4) 3/4” Screws (F).
7
Conduit Channel
8
F
H
1. Press Flexible Conduit into Conduit
Channel and SurfaceTrough.
Flexable Conduit
1. Position Tube Cl
amp at opposite end of
Surface Trough.
Install 3/4” Screw (F).
5
1. From under Work Surface, install
Surface Trough
Conduit Channel at end of Surface
Trough closest to the Power/Data
Distributor.
2. Secure to Work Surface with existing
Screw used to mount Surface Trough.
Surface Trough
L
Distributor
1. Finish placing Flexible Conduit in Cable Trough. Capture end of Curved Tube with
Curved Tube
I
K
J
9
Surface Trough and Tube Clamp. Slide Curved Tube on Conduit to take out Slack.
2. Secure Tube to Clamp with 1” Screw, Star Washer and Hex Nut.
Position other end of Tube at opening between Cladding on adjacent wall.
Cladding
Surface Trough
Tube Clamp
Curved Tube
10
1. Snap Cable Manager onto Curved Tube.
3. Adjust position of Curved Tube on flex conduit for proper location to ensure that flex
conduit is completely secure in Surface Trough.
Curved Tube
D
11
1. Snap Tube End onto Conduit on opposite side of Cladding.
Flexible Conduit
Curved Tube
GG
2. Push Tube End into Curved Tube.
WARNING
!
All electrical connections mu
st be fully engaged and locked.
Loose connections can cause fire and/or electrical shock.
12
Cord
Office Electrical System
Electrical Harness 1. Connect end of Electrical Harness into
left hand port in Power Harness of
2. Make sure electrical connection
is fully engaged.
Office Electrical System.
1. Run Data and Teleco
mmunication Lines through
customer supplied Face Plate.
2. Install Face Plate to Post with (2) Screws.
back of Power/Data Distributor and connect to
Power/Data Distributor
Data & Telecommunication Lines
Screw (2)
Face Plate
14
1. Insert 180 Degree Cover into 90 Degree Cover with Cut-Out over Work Surface
C
BE
E
1. Place 90 Degree Cover over bracket. Capture Wire Harness on one side of Cover
15
2. Install (2) 1/2” long Screws (E).
and Data and Telecommunication Lines on the other.
2. Install (3) 1/2” long Screws (E).
Support. Keep Harness on one side of
Cover and Data and Telecommunication Lines
Cut-Out
on the other.
Work Surface
Support
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Herman Miller My Studio Environments Product Instructions

Type
Product Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI