Vemer Energy-3x130 PWRi User manual

Brand: Vemer

Model: Energy-3x130 PWRi

Type: User manual

Vemer Energy-3x130 PWRi is a three-phase energy meter designed to operate in environments with measurement category III and pollution level 2. It is used to read active energy in three-phase systems. Below you will find brief product information.

The device has a power supply of 3x130 V AC phase-neutral (230VAC phase-phase) (-15% ÷ +10%) and a frequency of 50/60 Hz. It has a rated current of 5 A, a maximum current of 6 A, and a minimum start-up current of 15 mA. The maximum power consumption is less than 2.5 VA for both voltage and current circuits.

The meter constant is 1 imp = ¼ kWh. The voltage inputs have an input impedance of 2 MΩ, while the current inputs use coils with galvanic insulation between primary and secondary.

User Manual

ACTIVE ENERGY METER

Read all the instructions carefully

TheENERGY-400 and ENERGY-3x130 are electronic static devices to read active energy in

three-phasesystemsdesignedtooperateinenvironmentswithmeasurementcategoryIIIand

pollution level 2 according to EN 61010-1 standard.

SAFETY WARNINGS

To guarantee correct installation, proceed as follows:

1) The appliance should be installed by a qualified operator

2) The appliance should be installed in a panel in such a way as to guarantee that the

terminals are inaccessible after fitting

3) A protection device against over-currents should be installed in the electrical system,

upstream of the energy meter

4) Connect the instrument as shown in the alongside diagrams

5) Before touching the connector terminals make sure that the wires to be connected or

already connected to the instrument are not live

6) Touch the dip-switches only when the instrument is not powered

7) Do not power or connect the instrument if any part of it is damaged

8) The instrument must be installed and activated in compliance with current electric

system standards.

Code Model Description

VN964300 ENERGY-400PWR Three-phaseenergymeter400VAC

VN966800 ENERGY-3x130PWR Three-phaseenergymeter3x130VAC

VN967600 ENERGY-3x130PWRi Three-phaseenergymeter3x130VAC

TECHNICAL SPECIFICATIONS

• Powersupply:

- 3x230 V AC phase-neutral (400VAC phase-phase) (-15% ÷ +10%)

for Energy-400 model

- 3x130 V AC phase-neutral (230VAC phase-phase) (-15% ÷ +10%)

for Energy-3x130 models

• Frequency:50/60Hz

• Ratedcurrent:5A

• Maximumcurrent:6A

• Minimumstart-upcurrent:15mA

• Maximumpowerconsumption:

- voltage circuits < 2,5 VA

- current circuits < 2,5 VA

• Meterconstant:1imp=¼kWh

• Voltageinputs:inputimpedance=2MΩ

• Currentinputs:

 -shuntof0.022Ω(+/-10%)forPWR models

 -coilswithgalvanicinsulationbetweenprimaryandsecondaryforEnergy-3x130PWRi

model

• Twoopticinsulatedimpulseoutput:

- impulse duration < 100 ms

- voltage 9÷24 V DC

- current < 20 mA

• Insulation:

 -reinforcedbetweenimpulseoutputandotherterminals

- reinforced between terminals and parts accessible after installation

• CTavailable:5-10-25-50-75-100-125-150-200-250-300-400-500-600-8001000/5A

• Operatingtemperature:-10°C÷+45°C

• Storagetemperature:-25°C÷+70°C

• Relativehumidity:10÷90%noncondensing

• Classindex:classA(EN50470)

• Container:4moduleDIN

• Protectionlevel:IP20/IP40onthefront

INSTRUMENT DESCRIPTION

➀ Dip-switchforCTsetting

➁ Green warning light:lightsuptoindicatepoweron

➂ Red warning light:flashestoindicatethattheinstrumentismeteringenergy

(1flash=¼kWh)

➃ Yellow warning light:whenlittheinstrumentdetects¼kWhnegative(probable

incorrectentry)andremainslituntil¼kWhpositiveisdetected

ChecktheinsertionofCT:connectL1,L2,L3frompowerpaneltoP1ofCTand

connectP2ofCTtotheload.

➄ Impulseoutput:Opticallyinsulated

➅ Electro-mechanicalimpulsecounter:resolution1kWh

GUIDE TO INSTALLATION

1)Beforeinstallingtheinstrument,selecttherequiredtransformationratio,asshownin

panel C)

2)ForEnergy-3x130PWRimodelonly,theCTsecondariesmaybeconnectedtoearth

3)TheinstrumentshouldbeconnectedasshowninthepanelB),inaccordancewiththe

CTcurrentdirections

4)Iftheerroristofallwithintheclasslimitsoftheinstrument,itisnecessarytousethe

current transformer in its linear operating field.

5)IftheinstrumentisactivethepowershouldbeswitchedofftochangetheCTratio.

6)Incaseofchangestothedip-switchwiththeinstrumentactived,theselocksinfault

conditionwithredandgreenlightsalwayson.Inthisconditiontheinstrumentdoesn’t

coun.

 Torestorethecorrectoperation,repositiontheDIPswitchesintheinitialconditionor

resettheinstrumentbyremovingandrestoringpower.

REFERENCE STANDARDS

ConformitytoEUdirective:

2004/22/EC (MID)

2006/95/EC (Low Voltage - LVD)

isdeclaredwithreferencetothefollowingharmonisedstandards:

EN 61010-1

EN50470-1andEN50470-3

V3IS00244-100_02-2013

Mod. ENERGY-400 PWR

Mod. ENERGY-3x130 PWR

ENERGY-3x130 PWRi

Dimensions (A)

Connection diagrams (B)

Instrument description (C)

2 CT connection (PWRi only) WITHOUT neutral (3 wires)

1 kWh/pulse

Pulse output

I ≤ 20 mA

9÷24 VCC

PWRi

P1 P2

S1 S2

PWR

P1 P2

S1 S2

200

250

300

400

x/5 A

1 2 34x/5 A

1 2 34

100

125

150

500

600

800

1000

ON OFF

3 CT connection WITH or WITHOUT neutral (3 or 4 wires)

1 kWh/pulse

Pulse output

I ≤ 20 mA

9÷24 VCC

72 60

60 0 0

Vemer Energy-3x130 PWRi User manual

Brand: Vemer

Model: Energy-3x130 PWRi

Type: User manual

The meter constant is 1 imp = ¼ kWh. The voltage inputs have an input impedance of 2 MΩ, while the current inputs use coils with galvanic insulation between primary and secondary.

Download PDF

report

Vemer Energy-3x130 PWRi User manual

Vemer Energy-3x130 PWRi User manual

Related papers

Other documents