INSTRUCTION MANUAL
General Safety 4
Remote Control 8
Product Overview 9
Getting Started 10
Operating Instructions 12
Cleaning and Maintenance 15
Specifications 16
Customer Helpline Last Page
CONTENTS
4
Read this manual thoroughly before you start using the heater.
Store this manual, the completed warranty card, your receipt and the product packaging.
The safety precautions instructions reduces the risk of fire, electric shock and injury when
correctly complied to.
Please follow all instructions and take notice of all warnings.
Please follow instruction when installing this product in accordance with the instruction
manual. This product must be positioned in a suciently stable location, it can be potentially
hazardous due to falling when mounted and can cause injury, particularly to children if it
positioned incorrectly.
• Before installing this product, make sure your outlet voltage corresponds to the voltage
stated on the product rating label
• Do not use a damaged power cord, plug or loose outlet. Doing so may cause an
electric shock.
• Do not plug several devices into the same outlet. Doing so may cause the outlet to
overheat and start a fire. Make sure the outlet is readily accessible during operation
of the equipment.
• Do not bend, twist or kink the power cord excessively.
• Do not allow anything to rest on or roll over the power cord.
Doing so may cause a fire or an electric shock.
• Do not run the power cord near heat-producing appliances such as radiators, stoves or
irons. The excessive heat could melt the insulation and expose live wires, resulting in
fire or electric shock.
• Do not expose this product to water. The electrical insulation could be damaged
and cause electrocution. Do not touch the unit when barefoot or parts of your body are
wet or damp.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
GENERAL SAFETY
5
GENERAL SAFETY INSTRUCTIONS (Cont.)
• Do not cover the ventilation openings of the product with items such as newspapers,
tablecloths, curtains etc or insert objects into the slots available on the products.
As this could result in the product temperature rising and could cause a fire.
• If you notice any unusual odors or smoke around the unit, immediately disconnect the
unit from the outlet and contact the service center. Failure to do so may result in fire
or electric shock.
• When not using the unit for long periods of time or when you are moving the unit
please ensure to disconnect the power supply from the wall socket.
• Please beware that Dust could accumulate over time on the unit and cause it to generate
heat and or deteriorate insulation, which in turn may result in an electrical fire.
• Batteries from the remote control must be only removed by an adult, the adult must
ensure to keep them out of reach of infants and children. Seek medical attention
immediately if a child has swallowed a battery.
• To maintain the product do not use any chemical or cleaning agent or wet cloth, please
only ensure to utilize a dry cloth to wipe it down from marks or dust and only after
unplugging the product from the power socket.
• Do not direct airflow directly onto plants or animals, as long exposure can aect them.
• Please ensure to contact our call center for any repair or service required for the products
not doing so will make warranty on your product void.
• We assume no liability for any eventual damages to property or injury to persons caused
by misuse of the product or noncompliance with these instructions.
Please make sure upon positioning this product, the place is:
• Not wet or damp and Well ventilated
• Away from direct sunlight or heaters.
• Do not place containers with liquids, if liquid falls inside the products it may result in
short-circuit, fire or electric shock.
• Do not place small metallic objects on top of the unit or block the openings as it will
reduce operating eciency of the air con with failures or damages.
• The appliance shall under no circumstances, be covered with insulating material
or similar material.
WARNING: In order to avoid overheating, do not cover the heater.
• Away from splashes or food.
• Protected from excessive dust or grease.
• The heater must not be located immediately next to socket outlet.
• Do not use this heater in the immediate surrounding of a bath, shower or a swimming pool.
6
GENERAL SAFETY INSTRUCTIONS (Cont.)
• This appliance is intended for heating indoor domestic environments. It is not
suitable for commercial, industrial or trade use. Do not use it for any other purpose
(such as drying clothes, etc.), and only use it as described in this manual.
• Do not use the unit outdoors. It is for indoor use only.
• WARNING: Do not cover! Do not cover the heater or obstruct any air inlet or outlet
grilles. Obstructing these openings causes a fire hazard, reduces the operating eciency
and may lead to malfunction or damage.
• Do not insert any objects, or your fingers, into the air outlet, and make sure to warn
children of the dangers. Keep ventilation openings clear of obstructions.
• Close supervision is necessary when any appliance is used by or near children. Cleaning
and user maintenance shall not be made by children without supervision.
DO NOT INSTALL/USE THE APPLIANCE IN THE FOLLOWING AREAS:
- outdoors or where water is likely to splash
- near a bath, shower, laundry basin or swimming pool
- in an area where oil is likely to splash
- near a hot gas or electric burner, or sources of fire
- near sources of heat, or exposed to direct sunlight
- in an area where furniture or other objects can obstruct the airflow
- in the presence of flammable substances or vapour such as alcohol, insecticides,
petrol, etc.
- at a dry cleaner’s premises.
7
GENERAL SAFETY INSTRUCTIONS (Cont.)
• Ensure that there is sucient distance from the wall, fixtures or other
appliances. The distance must be at least 1.5 m from the front and sides wall of
the appliance to exclude the risk of fire.
• DO NOT place near any combustible materials, such as fabrics, blankets,
curtains, etc. May result in catching on fire or burning.
• Place the unit on a flat surface to reduce the risk of it tipping over. Always keep
it upright during installation and use. The unit will turn o automatically if acci
dentally tipped over.
• We accept no responsibility for any eventual injuries or damages caused by
improper installation, faulty use or failure to follow the instructions.
WARNING:
• Do not expose the appliance to high heat, sparks and open flames.
• Do not pierce or burn the appliance.
• Maintenance must only be carried out by properly qualified, authorised personnel.
If the appliance requires maintenance or service, contact our after sales support
centre info@ayonz.com
Do not use if there are visible signs of damage to the heater; Use this heater on a horizontal and
stable surface, or fix it to the wall, as applicable.
WARNING: Do not use this heater in small rooms when they are occupied by persons not
capable of leaving the room on their own, unless constant supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any other flammable material
a minimum distance of 1 m from the air outlet.
8
REMOTE CONTROL
Using the Remote Control
• Do not mix old and new batteries in the remote
• Do not use dierent types of battery
• If you do not intend to use the unit for a long time, please remove batteries from the
remote to avoid accident.
• Keep batteries away from children and pets.
• Never throw batteries into a fire.
• Do not drop, or impact the remote control as it void warranty immediately.
• The remote control operate at a range of 5 to 6M eectively
• Do not expose the remote control sensor to a bright light.
INSTALLING BATTERIES
1. Open the battery box on the back of remote control, and install
2 x AAA batteries (not included).
2. Make sure to match the battery polarities ( + / - ) with the remote
control compartment.
3. Put on the back cover.
OFF
HEATING
MODE
SWING
ON
COOL
SPEED
TIMER
9
PRODUCT OVERVIEW
10
GETTING STARTED
BEFORE FIRST USE
• Unpacking: This product has been packaged to protect it against
transportation damage. Unpack the appliance and keep the original
packaging carton and materials in a safe place. It will help prevent
any damage if the product needs to be transported in the future, and
you can use it to store the appliance when it is not in use. In the event
it is to be disposed of, please recycle all packaging materials where
possible.
• Safe packaging disposal: Plastic wrapping can be a suocation
hazard for babies and young children, so ensure all packaging
materials are out of their reach and disposed of safely.
• Inspection: Unwind the cord to its full length and inspect it for
damage. Do not use the appliance if the appliance or its cord have
been damaged or are not working properly. In case of damage,
contact our after sales support centre for advice on examination,
repair or return of the damaged product.
ASSEMBLY OF THE BASE
• Before the appliance can be used, the two piece base must be fitted
together and attached to the underside of the fan.
• Place the two halves of the base upside down and align (A), then
press to lock the two halves together and secure with 4 screws (B).
• With the fan body turned upside down, align the base onto the fan
underside, insert and tighten with a further 4 screws (C).
• Invert the product to the correct orientation, place on the floor and check
the product is stable. Carts are secure and then place the appliance in the
correct.
• This device is a fixed appliance, and the fixing method is as follows:
1. Use the setscrew to fixed the machine, when you use it on the
uneven ground.
2. Use the electric drill to make 2 holes on the ground. Then use
the setscrew to fixes the machine.
11
UPPER WATER TRAY
• The upper water tray (lift lid above control panel) is accessible via a
hinged cover. Locate and fit the carbon filter cartridge - place in the
allocated slot.
• Water tank can alternatively be filled / topped up from this location,
add water slowly to prevent spillage.
GETTING STARTED (Cont.)
12
OPERATING INSTRUCTIONS
USING THE APPLIANCE
• Decide on a location for the CK2IN1HEA, convenient to a supply
socket. It is designed for indoor use. Fixing on a dry, level surface.
• Insert the power plug into an appropriate electrical outlet and switch
on power to the outlet.
SWITCHING THE APPLIANCE ON/OFF
• Press the On/O button on the control panel once to switch the fan on,
the LED display will show the current ambient temperature.
COLLING
• To activate the evaporative cooling function, press the “Cool” button. This
will activate the pump which will draw water from the tank to the upper
collection tray which will filter internally over the evaporative inlet filter.
Water tank can be filled via the water tank directly or via the upper water
tray.
WARNINGS:
• Before operation, ensure the water tank has been filled with fresh clean
water to at least the minimum level and not beyond the maximum level.
Refrigerated water can be used to assist with cooling.
• Never use water any hotter than 30ºC.
Maximum tank capacity is 3L, never fill beyond maximum level.
• The tank cannot be completely removed, never apply force or try to fully
remove.
• We recommend movement of the product is limited when the tank is full,
decide on the intended location before filling. If relocation is required,
take care to gently move as to avoid water spilling from the tank.
• Never leave the cooling function on for extended periods with the tank
empty, this will cause the pump to run dry and may result in damage.
13
OPERATING INSTRUCTIONS (Cont.)
TIMER
• To activate the timer function, press the “TIMER” button, each
subsequent press will step through from 0-12 (hours). When the
desired time is reached, the LED screen will flash On/O to indicate
the selected time (in hours) and the clock symbol will be activated to
indicate the timer has been set. At the end of the present period, the
fan will automatically switch o.
SPEED SELECTION
• To control the fan speed, push the “SPEED” button to cycle between Low
- Medium and High speeds.
SWING / OSCILLATION OF THE OUTLET GRILLE
• To switch on the swing grille function, press the “SWING” button. The
outlet air grille will pivot from one side to the other.
• To switch o, press the “SWING” button once when the air is blowing in
the desired direction.
MODE (FAN FUNCTION)
• There are three fan functions, Continuous (normal) / Natural and Sleep.
One press of the “Mode” button activates Natural Wind function, this is
indicated by the tree symbol. A second press activates the Sleep Wind
Function, indicated by the moon symbol. A third press activates the
continuous (normal) wind function. Subsequent presses of the button will
cycle through the options.
• Natural Wind: the fan operates with varying speeds and switching On/O
with a change every 2-3 seconds.
• Sleep Wind - On high speed, the first half hour operates as high Natural
wind, the second half hour operates as medium speed Natural wind, after
which time it operates as low speed Natural wind.
On Mid speed, the first half hour operates as mid speed Natural wind,
after that it continues to operate as low speed Natural wind.
On Low speed, it operates as low speed Natural wind continuously.
14
OPERATING INSTRUCTIONS (Cont.)
HEATER SELECTION
• To activate the heating function, push the “HEATING” button to cycle
between Low and High heat.
• NOTE: When using in the heating mode for the first time, or after a
long period of storage, it is normal for the heater to emit a burning
odour due to lubricants used during production or from dust deposits,
this will pass quickly. This is no cause for concern, ensure good
ventilation.
REMOTE CONTROL
• When using the remote control, the emitter of the front section of the
remote control must be aligned (pointed towards) the receiving window
of the fan body (near display screen).
• The remote control will have an operating distance of approximately 5m
and within an angle range of 30ºC.
• The remote control can be used to activate / control all functions
described on the previous page.
BATTERY FITMENT / REPLACEMENT
• For first use or if the battery becomes flat, gently press on the upper
portion of the battery cover, push and slide to remove the cover and
access the battery compartment at the back side of remote control.
• Fit 2 x AAA type batteries carefully observing the battery polarity
markings.
• Slide the battery cover back into the compartment of the remote control
and make sure it has securely locked in position.
BATTERY PRECAUTIONS
WARNING! - Keep batteries out of reach of children. Swallowing
may lead to serious injury or death in as little as 2 hours due to
internal burns. If swallowed, go straight to a hospital.
15
CLEANING AND MAINTENANCE
CLEANING AND MAINTENANCE
• Dusting: Clean your fan periodically by lightly running a vacuum
cleaner nozzle (soft brush) over the front outlets and rear grilles to
remove any dust or dirt that may have accumulated inside or on the
unit. Alternatively, use a soft, dry cloth for dusting.
• Stubborn stains: Use a slightly damp, soapy cloth for stubborn stains
but be sure the cloth is not too wet. Use caution around the housing.
Do not allow the electrical components to be exposed to water.
• Storage: If not in use for an extended period, store in a safe, dry
location, protected from dust and located so it is not in direct
sunlight. We recommend using the original carton for storage of the
disassembled product (follow the assembly instructions in reverse
order to disassemble). Alternatively, place a large plastic bag or piece
of material over the top of the cleaned appliance for dust protection.
RESPONSIBLE DISPOSAL
• At the end of its working life, make the appliance unserviceable by
unplugging if from the power outlet and cutting the power cord.
• Do not throw this appliance out with your household rubbish.
Electrical and electronic products contain substances wich can have a
detrimental eect on the environment and human health if disposed
of inappropriately. Observe any local regulations regarding the
disposal of electrical consumer goods and dispose of it appropriately
for recycling. Contact your local council for advice on recycling
facilities in your area.
WARNING!
• Before cleaning, maintenance or moving the appliance, switch o and
unplug it from the wall outlet.
• Do not immerse the appliance in water or other liquids. Do not spray it
with liquids. Do not allow water to drip on or into the housing.
• Never use petrol, solvents, harsh detergents, or abrasive or alkaline
cleaners on the fan.
16
SPECIFICATIONS
Rating 220-240V ~ 50-60Hz
Power
HEATING POWER 2200 W
COOLING POWER 65W
Weights
NET 8.7 kg
GROSS 6.8 kg
Unit Dimensions 320 (w) x 320 (d) x 960 (h) mm
17
THIS PAGE HAS
BEEN LEFT BLANK
ON PURPOSE.
18
THIS PAGE HAS
BEEN LEFT BLANK
ON PURPOSE.
19
THIS PAGE HAS
BEEN LEFT BLANK
ON PURPOSE.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
