Ferm FPCD 1800 LK Owner's manual

Art.no. CDM1064

FPCD-1800LK

www.ferm.com

0810-23.1

DK

N

FIN

S

I

P

E

F

NL

D

GB

USERS MANUAL 05

GEBRAUCHSANWEISUNG 09

GEBRUIKSAANWIJZING 15

MODE D’EMPLOI 20

MANUAL DE INSTRUCCIONES 25

MANUAL DE INSTRUÇÕES 30

MANUALE UTILIZZATI 35

BRUKSANVISNING 40

KÄYTTÖOHJE 44

BRUKSANVISNING 49

BRUGERVEJLEDNING 53

Page is loading ...

GB

5

Ferm

COMBI DRILL

Thank you for buying this Ferm product.

By doing so you now have an excellent product,

delivered by one of Europe’s leading suppliers. All

products delivered to you by Ferm are

manufactured according to the highest standards

of performance and safety. As part of our

philosophy we also provide an excellent customer

service, backed by our comprehensive warranty.

We hope you will enjoy using this product for many

years to come.

The numbers in the text refer to the diagrams

on pages 2 - 4.

Read the operating instructions carefully

before using this device. Familiarise

yourself with its functions and basic

operation. Service the device as per the

instructions to ensure that it always

functions properly. The operating

instructions and the accompanying

documentation must be kept in the

vicinity of the device.

Contents

1. Machine information

2. Safety instructions

3. Mounting accessories

4. Operation

5. Service & maintenance

1. MACHINE INFORMATION

Technical specifications

Voltage 18 V

Drill speeds 2

Max. torque, steel 62 Nm

Max. torque, wood 42 Nm

No-load speed

Position I 0-450/min

Position II 0-2250/min

Hammer speed 0-40500/min

Weight (without battery) 1.88 kg

Lpa (acoustic pressure) 83 + 3 dB(A)

Lwa (acoustic power) 94 + 3 dB(A)

Vibration 12.89 + 1.5 m/s

2

Contents of packing

1 Charger

1 Lithium-Ion Battery

1 Storage case

1 Combi drill

1 Side handle

1 Depth stop

1 Connection rod for depth stop

1 Operating instructions

1 Safety instructions

1 Warranty card

Check the appliance, any loose parts and

accessories for damage caused during transport.

Product information

Fig. 1

1. Chuck

2. Torque setting ring

3. Speed selector switch

4. LCD display

5. LED light switch

6. Spirit level

7. LCD display switch

8. Direction switch

9. On/off switch

10. Battery release button

11. Side handle

12. LED lights

13. Depth stop rod

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of

life or damage to the tool in case of non-

observance of the instructions in this

manual.

Indicates electrical shock hazard.

The number of revolution of the machine

can be electronically set.

Rotation left/right.

Do not use in rain.

GB

6 Ferm

Wear eye and ear protection.

Do not dispose of in household waste.

Specific safety instructions:

The tool is suitable for use as a screwdriver,

regular drill and impact drill. Any other application

is specifically excluded.

Use only impact drill bits and accessories that •

are designed for use with an impact drill when

using this machine in the impact drill mode.

Standard drill bits are NOT designed for use in

an impact drill and must NOT be used with an

impact drill. They may shatter and possibly

cause serious injury.

Do not drill material too small to be securely •

held.

Always keep hands out of the path of the drill •

bit. Avoid awkward hand positions where a

sudden slip could cause your hand to move

into the path of the drill bit.

Secure work piece. Use clamps or a vice to •

hold the work piece. It is safer than using your

hand and it frees both hands to operate the

tool.

Make sure there are no nails or foreign objects •

in the part of the work piece to be drilled.

To avoid injury from accidental starting, always •

remove the battery from the tool before

installing or removing a drill bit.

Do not install or use any drill bit that exceeds •

175 mm (7”) in lengths or extends more than

150 mm (6”) beyond the chuck jaws. They can

bend or break suddenly.

Before starting the operation, jog the switch •

shortly to make sure the drill bit does not

wobble or vibrate.

Do not use fly cutters or multiple-part hole •

cutters, as they can come apart or become

unbalanced during use.

Make sure the spindle has come to a complete •

stop before touching the chuck or attempting

to change the drill bit.

Always make sure the chuck is tight and the •

drill bit firmly tightened in the chuck before

starting the drill.

When drilling into smooth, hard surfaces such •

as metal, use a centre punch to mark the desi-

red hole location. This will prevent the drill bit

from slipping off centre as the hole is started.

Use a masonry bit with the drill in impact mode •

ONLY when drilling in concrete or masonry.

Always use carbide tipped masonry bits when •

drilling in concrete or masonry

This appliance is not intended for use by •

persons (including children) with reduced

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instructions

concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that •

they do not play with the appliance.

Follow all safety rules and warnings,

also those which are included with the

battery pack and charger used with this

tool. Failure to do so may result in

serious injury or damage to the charger

and the battery pack

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Installing the auxiliary handle

Fig. 2 + 3

Install the auxiliary handle for two handed

operation of the drill. This is particularly important

for impact drilling in concrete. The auxiliary handle

can be installed on either the left or right side of

the combi drill.

Insert the threaded mounting screw through •

the depth stop rod clamp (14) and into the

threaded hole in the housing.

Turn the auxiliary handle (11) clockwise to •

tighten it into the housing.

Make sure the key on the depth stop

clamp is aligned with the notch in the

drill housing. This will prevent it from

unexpected turning and the auxiliary

handle from coming loose.

Screwdriver bits and drill bits can be stored in the

auxiliary handle.

To remove the end cap (15), pull it of the auxiliary

handle. To install, push it back on the auxiliary

handle.

GB

7

Ferm

Installing the depth stop rod

Fig. 1 + 2

The depth stop rod (13) is used as a gauge to

control the depth of the drilled hole. It can be used

with the combi drill in either the normal drilling

mode or the impact drill mode.

Turn the auxiliary handle (11) counter •

clockwise about three turns to open the depth

stop rod mounting clamp (14).

Insert the depth rod into the matching hole in •

the depth stop rod mounting clamp.

Position the depth stop rod so it will contact •

the work piece when the drill reaches the

appropriate depth.

When the depth stop rod is properly •

positioned, tighten the depth stop rod

mounting clamp by turning the auxiliary handle

clockwise.

Tighten the handle by hand only. Do not

over tighten the handle or you will

damage the handle or the housing.

Installing drill bits

Fig. 4

Never hold the chuck and use the drill

power to loosen or tighten bits. This can

result in serious injury.

To open the keyless drill chuck, rotate the •

chuck body (1) in a clockwise direction until

the jaws (16) open wide enough to accept the

bit. (17)

Insert the bit, over the full length of the jaws, •

into the chuck.

Tighten the chuck jaws onto the bit by turning •

the chuck body in a counter clockwise

direction.

As the chuck jaws begin to tighten on the bit, •

you will hear a clicking sound. Continue to

rotate the chuck body until the clicking stops

and you can no longer turn it any further by

hand. The chuck is now locked.

The bit must be properly inserted with all

three of the chuck jaws holding the bit

centred in the chuck. Make sure the

chuck jaws grasp the flat sides of a

screwdriver bit. Failure to do so could

cause the bit to be thrown from the

chuck, resulting in possible serious

injury or damage to the chuck.

To remove a bit, open the keyless drill chuck by •

rotating the chuck body in a clockwise direc tion

until the chuck jaws open and remove the bit.

Connecting and removing the battery

Fig. 1 + 5

Ensure that the direction reversing switch (8) •

is in the central position in order to prevent the

appliance from being switched on

unexpectedly.

Insert the battery into the base of the •

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking button (10) on either side •

before removing the battery, and disengage

the battery from the base of the appliance.

Only use batteries of the following type. Using any

other batteries could cause serious injury or

damage the tool.

CDA1051: FPB-1800L, 18V Lithium-Ion

CDA1053: FPB-1800N, 18V NiMH

The following charger can be used to charge these

batteries.

CDA1052: FPL-1800 (Lithium-Ion and NiMH)

CDA1054: FPL-1800N (NiMH only)

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance firmly and press the drill

steadily onto the workpiece. Do not overload the

appliance. Only use drills with no visible wear.

Worn drills will have a bad effect on the functio-

ning of the appliance. Do not cover the air vents.

This will reduce the motor cooling, and possibly

lead to overheating the motor.

Adjusting the torque

Fig. 6 + 7

Rotate the adjustment ring (2) to align the correct

torque setting number with the torque indicator

arrow (18). Use the chart below for the correct

torque setting:

1-5: For driving small screws

6-10: For driving medium sized screws into soft

materials

GB

8 Ferm

11-15: For driving screws into soft and medium-

density materials

16-20: For driving screws into hardwood

21-25: For driving large screws

Drill icon: For drilling

Hammer icon: For impact drilling

If material is particularly soft or porous,

set the torque clutch at a lower setting to

avoid overdriving the screw.

Adjusting the speed

Fig. 1

The appliance has two drill speeds.

For slow drilling or for driving or removing •

screws, set the speed selection switch (3) to

‘1’.

For fast drilling set the speed selection switch •

to ‘2’.

Never switch over when the motor is

running!

Driving and removing screws

Fig. 1

Set the direction reversing switch (8) to •

position ‘’ in order to drive screws.

Set the direction reversing switch (8) to •

position ‘’ in order to remove screws.

Ensure that the direction reversing

switch (8) is always set to ‘’ during

drilling.

Switching the device on and off

Fig. 1

Depress the on/off switch (9). It regulates the •

speed of the appliance by transmitting power

to the switch.

Release the on/off switch (9) to halt the drill •

chuck immediately, it will no longer run on.

Move the direction reversing switch (8) to the •

centre in order to lock the appliance in its

disabled state.

The drill will turn at its slowest speed when the

switch is depressed lightly. The drill will turn at its

fastest speed when the trigger is fully depressed.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Spirit level

Fig. 8

The drill is equipped with a dual reading horizontal/

vertical level to assist in keeping the drill “level”

while drilling horizontal and vertical holes. The

horizontal level (21) is located in the top of the drill

housing. The vertical level (22) is located on the

rear of the drill housing.

To maintain a level drilling position, hold the drill

where the level bubble is centred in the level

indicator circle.

LCD display

Fig. 9

This combi drill is equipped with an LCD display

(4) on top of the drill housing

To turn the display on, press the display button •

(27) once. To turn the display off, press the

display button again.

The light icon (25) will become visible when •

the LED work lights are turned on.

The clock (28) and minutes (24) remaining •

icons indicate the number of minutes of

running time that are available before the

battery requires recharging (Lithium Ion

battery only)

The battery icon (23) indicates the amount of •

charge remaining in the battery. Each charge

bar displayed indicates approximately 10%

charge remaining in the battery. A total of 10

charge bars indicates a fully charged battery.

Dual LED work lights

Fig. 1 + 9

Dual LED lights (12) are located behind the torque

ring. The LED light switch button (26) is located

below the LCD display on top of the drill.

To turn the LED lights on, press the LED light •

switch once.

To turn the LED lights off, press the LED light •

switch again.

The display must be turned on first, in order for the

LED lights to work.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

D

9

Ferm

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly clean

the machine housing with a soft cloth, preferably

after each use. Keep the ventilation slots free from

dust and dirt. If the dirt does not come off use a

soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. Separate you find an exploded view

showing the parts that can be ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material.

Therefore please make use of options for recycling

the packaging.

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Warranty

The warranty conditions can be found on the

separately enclosed warranty card.

KOMBIBOHRMASCHINE

Vielen Dank, dass Sie sich für den Kauf dieses

Ferm-Produkts entschieden haben.

Sie besitzen nun ein hervorragendes Produkt von

einem führenden europäischen Lieferanten.

Alle Ferm-Produkte werden nach höchsten

Leistungs- und Sicherheitsstandards gefertigt.

Gemäß unserer Philosophie bieten wir Ihnen einen

exzellenten Kundenservice sowie eine vollständige

Garantie auf unsere Produkte.

An diesem Produkt werden Sie noch viele Jahre

Ihre Freude haben.

Die Ziffern im nachstehenden Text verweisen

auf die Abbildungen auf Seite 2 - 4.

Lesen Sie diese Bedienungsanleitung

aufmerksam, bevor Sie die Maschine in

Betrieb nehmen. Machen Sie sich mit

der Funktionsweise und der Bedienung

vertraut. Warten Sie die Maschine

entsprechend der Anweisungen, damit

sie immer einwandfrei funktioniert. Die

Betriebsanleitung und die dazugehörige

Dokumentation müssen in der Nähe der

Maschine aufbewahrt werden.

Inhalt

1. Maschineninformation

2. Sicherheitsanweisungen

3. Montagezubehör

4. Betrieb

5. Service & Wartung

1. MASCHINENINFORMATIONEN

Technische Daten

Spannung 18 V

Bohrgeschwindigkeiten 2

Max. Drehmoment, Stahl 62 Nm

Max. Drehmoment, Holz 42 Nm

Leerlaufdrehzahl

Position I 0-450 U/min

Position II 0-2250 U/min

Schlagwerk Drehzahl 0-40500 U/min

Gewicht (ohne Akku) 1,88 kg

Lpa (Schalldruck) 83 + 3 dB(A)

Lwa (Schallleistung) 94 + 3 dB(A)

Schwingung 12,89 + 1,5 m/s

2

Page is loading ...

62

Ferm

Spare parts list

FPCD-1800LK

Position Description No.

1+2 Chuck complete 490001

3+4 Gearbox complete 490002

5 Motor assembly 490003

6 Speed selector button 490004

7 LED worklights 490005

8till11 Auxiliary handle complete 490006

12+15+22+25 Housing complete 490007

13+23+24 Screw set 490008

14+18 LCD display complete 490000

16+17 Spirit level complete 490009

19 Direction button 490010

20 Switch assembly 490011

21 Battery release box 490012

26 Battery CDA1051

* Charger CDA1052

Page is loading ...

Ferm FPCD 1800 LK Owner's manual

This manual is also suitable for

Ferm FPCD 1800 LK Owner's manual

in other languages

Related papers

Other documents