AMX modero NXT-CV10 Quick start guide

AMX
Brand
AMX
Model
modero NXT-CV10
Type
Quick start guide

This manual is also suitable for

Quick Start Guide
NXD/T-CV10 10”Modero Widescreen Video Touch Panels
For more detailed installation, configuration, programming, file transfer, and operating
instructions, refer to the NXD-CV10/NXT-CV10 Instruction Manual, available on-line at
www.amx.com.
ATTENTION!
Verify you are using the latest NetLinx Master and Modero touch panel firmware
(available from www.amx.com). Verify the TPDesign4 program being used is
Version 2.6 or higher.
Overview
These are the first 10" diagonal Widescreen Color Active video-capable touch panels
in the control and automation industry.
These Color Video (CV) panels display NTSC/PAL/SECAM video formats within
variable sized windows. They include a built-in microphone, speakers, audio/
headphone connector, and six NetLinx programmable pushbuttons (only available on
CV10 models with the button feature available (-02K and -03K)).
Table Top models use AMX's exclusive SmoothTilt™ technology for effortless
adjustment of the viewing angle.
Each panel is sold only as part of a CV10 Kit which includes both a panel and an
NXA-AVB/ETHERNET Audio/Video Breakout Box (FG2254-10).
The the three available Kit configurations are:
• NXD-CV10 (FG2259-02K) - 10" Wall Mount Kit (with buttons)
(includes an NXD panel and NXA-AVB/ETHERNET Breakout Box).
• NXT-CV10 (FG2259-01K) - 10" Table Top Kit (without buttons)
(includes both an NXT panel and an NXA-AVB/ETHERNET Breakout Box).
• NXT-CV10/PB (FG2259-03K) - 10" Table Top Kit (with buttons)
(includes both an NXT panel and NXA-AVB/ETHERNET Breakout Box).
Specifications
Panel Connectors
FIG. 2 shows the connectors located on the CV10 Modero Video panels. The Audio/
Video RJ-45 connector provides differential audio/video signals between the touch
panel and the NXA-AVB/ETHERNET. This connector routes Composite video, Stereo
(left/right) audio, and microphone audio.
NXA-AVB/ETHERNET Breakout Box
FIG. 3 shows the front and rear connectors on the NXA-AVB/ETHERNET breakout
box. This breakout box can be mounted on either a horizontal flat surface or in an
equipment rack (by removing the front faceplate and securing it to an optional AC-RK
Rack Kit).
FIG. 1
10" Modero Widescreen Video Touch Panels
CV10 Specifications
Dimensions (HWD):
NXA-RK10
(FG2904-54)
NXD-CV10
(FG2259-02)
NXT-CV10
(FG2259-01/03)
CB-TP10
(FG036-10)
• 5 RU (rack units) high (22.15 cm)
8.72" x 19.0" x 0.50" (22.15 cm x 48.26 cm x 1.27 cm)
• Faceplate included: 7.96" x 11.16" x 3.32"
(20.22 cm x 28.34 cm x 8.43 cm)
• Fully raised: 8.71" x 11.16" x 7.38" (22.12 cm x 28.34 cm x 18.75 cm)
Fully lowered height: 4.53" (11.51 cm)
• Conduit/wallbox: 5.47" x 7.23" x 3.40"
(13.90 cm x 18.40 cm x 8.64 cm) (optional)
Power Requirements
(stand-alone CV10):
• Constant current draw: 1.2 A @ 12 VDC (stand-alone)
• Startup current draw: 1.8 A @ 12 VDC (stand-alone)
Power Requirements
(CV10 and BASE/1):
• Constant current draw: 2.6 A @ 12 VDC
• Startup current draw: 3.9 A @ 12 VDC
Minimum power
supply required:
• PSN2.8 Power Supply (FG423-17)
- when used with a stand-alone CV10 unit.
• PSN4.4 Power Supply (FG423-45)
- when a CV10 is connected to a BASE/1.
Memory: • 64 MB SDRAM
• 64 MB Compact Flash (upgradable to 1 GB - factory programmed)
Weight: • NXD-CV10: 2.65 lbs (1.20 kg)
• NXT-CV10: 4.75 lbs (2.15 kg)
Certifications: • FCC Part 15 Class B, CE, and IEC 60950
Panel LCD
Parameters:
• Aspect ratio: 16 x 9
• Brightness (luminance): 350 cd/m2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 250:1
• Display colors: 256 thousand colors (18-bit color depth)
• Dot/pixel pitch: 0.28 mm
• Panel type: TFT Color Active-Matrix
• Screen Resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency
• Video format: NTSC, PAL, and SECAM
Viewing Angle: • 95° total viewing angle
• Vertical: + 45° (up from center) and -65° (down from center)
IR Reception Angle: •Horizontal: + 50° (left and right from center)
• Vertical: + 30° (up and down from center)
NXD panel
(WallMount)
NXT panel (Table Top)
CV10 Specifications (Cont.)
Supported Audio
Sample Rates:
• 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz,
12000Hz, 11025Hz, and 8000Hz.
Front Panel: • Light Sensor: Photosensitive light detector for automatic adjustment of
the panel brightness
• Motion Sensor (PIR): Proximity Infrared Detector to wake the panel
when panel is approached
• IR Receiver: 38 KHz and 455 KHz AMX IR frequencies
• Sleep Button: Pushbutton (grey) provides both access to the Setup
and Calibration page and toggles the panel between a "sleep" or
"wake" state
• Microphone: Used for intercom applications (requires the
NXA-AVB/ETHERNET Breakout Box for analog communication)
• Speakers: Stereo output with a frequency response of 500 Hz - 7 KHz
• LEDs: 6 blue LEDs (support On and Off).
- Both the LEDs and pushbuttons are not available with the
NXT-CV10 panel (FG2259-01) containing no buttons.
• 6 programmable pushbuttons
Rear Connectors: • Mini-USB Connector: 5-pin Mini-USB connector used for
programming, firmware update, and touch panel file transfer between
the PC and the target panel
• Stereo Output Connector: Stereo output through a 3.5mm mini-jack
(for use with external speakers or headphones)
• Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps communication
• USB Connector: Type A USB port connects an external keyboard or
mouse device for use with Virtual PC applications
• Audio/Video Connector: RJ-45 connection for A/V signals (via CAT5)
between the NXA-AVB/ETHERNET Breakout Box and the panel
• Power: 2-pin 3.5 mm mini-Phoenix connector
Operating /Storage
Environments:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included
Accessories:
• Installation Kit for 10" NXD panels (KA2259-02):
- 2-pin 3.5 mm mini-Phoenix connector (41-5025)
- Three Drywall clips (62-5924-05) and #6 - sheet metal screws
(80-0192)
- Four Phillips-head screws (#4-40 x 0.250 Black) (80-0112)
• Installation Kit for 10" NXT panels (KA2259-01):
- 2-pin 3.5 mm mini-Phoenix connector (41-5025)
- One CAT5 Table Top Suppression Ferrite (04-0014)
- One cylindrical CAT5 USB Mouse Suppression Ferrite (04-0018-SA)
• Modero Table Top Cable (CA2250-50) provided with all NXT panels
• NXA-AVB/ETHERNET Breakout Box (FG2254-10)
- Provides video/audio distribution to the A/V panel over CAT5 cable
(up to 200’/60.96 m) and accepts either Composite or S-Video
• Trim Ring with button openings (60-2259-05)
(factory installed on -02 and -03 panel models only)
• Trim Ring without button openings (60-2259-04) (NXD models only)
Other AMX
Equipment:
• CB-TP10 Conduit/Wallbox (FG036-10)
• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
• NXA-BASE/1 Battery Base Kit (FG2255-05K):
- battery base and single NXT-BP battery
• NXA-RK10 Rackmount Kit for 10" Wall Mount panels (FG2904-54)
• NXA-WC80211GCF, 802.11g Compact Flash Wireless Card Upgrade
Kit provides wireless Ethernet support (FG2255-07)
• NXT-BP Battery (FG2255-10)
• NXT-CHG Kit (FG2250-50K): single charger and 2 NXT-BP batteries
• PSN2.8 Power Supply (12 VDC) (FG423-17)
• PSN4.4 Power Supply (12 VDC) (FG423-45)
• Upgrade Compact Flash (factory programmed with firmware):
NXA-CV10CF128M - 128 MB Compact Flash card (FG2116-65)
NXA-CV10CF256M - 256 MB Compact Flash card (FG2116-66)
NXA-CV10CF512M - 512 MB Compact Flash card (FG2116-67)
NXA-CV10CF1G - 1 GB Compact Flash card (FG2116-68)
FIG. 2 Connector layout on the CV10 Touch Panels
A
PROGRAM
10/100
ETHERNET
KEYBOARD /
MOUSE
AUDIO / VIDEO
PWR
L
12VDC
Stereo
Audio-Video from
Ethernet
Power
NXA-AVB/ETHERNET
(CAT5)
Keyboard/Mouse
USB connector
Mini-USB
(Program Port)
(CAT5)
Output
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
12/07
©2007 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2259-01 REV: F
Wiring the NXA-AVB/ETHERNET Connectors and Cables
The inputs and outputs on the breakout box are separated into front and rear
connectors. The rear connectors are used to input external signals. The front
connectors are used to communicate signals between the NXA-AVB/ETHERNET
and a target Modero panel. FIG. 4 provides a layout of the wiring connection both into
and from the breakout box.
Power should be applied to the NXA-AVB/ETHERNET only after all connections
have been secured onto both the box and target panel.
Use a standard CAT5 Ethernet cable (connected to the rear of the Table Top Panel or
to the side of the Wall Panel) to provide both communication and 10/100 network
connectivity between the panel, breakout box, NetLinx Master, and the network. The
rear-panel wiring connections are described below (from left to right):
Wiring for Unbalanced Audio
Use FIG. 5 to configure an unbalanced audio connection.
Wiring for Balanced Audio
Use FIG. 6 to configure a balanced audio connection.
Modero Setup and System Connection
1. Carefully remove the panel from the shipping box, peel the protective
plastic cover from the LCD and apply power to the panel.
2. From below the LCD, press the grey Front Setup Access button for 6 sec-
onds (passing-over the Setup page) to access the Calibration setup page
and follow the on-screen instructions.
3. Press the on-screen Protected Setup button on the Setup page.
4. Enter the panel password into the keypad (default is 1988).
5. Press the Device Number field to open the on-screen Device Number
keypad and enter a value for the panel (default is 10001).
6. Press Done when finished and press the on-screen Reboot button to
cycle power to the panel.
7. Press the grey Firmware Setup Access button for 3 seconds to open the
Setup page and touch the on-screen Protected Setup button.
8. Repeat step 4 to continue to the Protected Setup page.
9. Press the System Settings button to open the System Settings page
(FIG. 7).
10. Toggle the DHCP Static field to DHCP.
11. Toggle the Type field to Ethernet.
12. Toggle the Mode field to URL.
13. Enter both the System Number and IP Address of the target Master.
14. Enter a valid Username and/or Password if the target Master is secured.
15. Press the Back button and then press the on-screen Reboot button to
save any changes and cycle power.
FIG. 3 Connector layouts on the NXA-AVB/ETHERNET Breakout Box
FIG. 4 NXA-AVB/ETHERNET Breakout Box connector wiring diagram
AUDIO IN: 6-pin mini-Phoenix connector, divided into left and right audio chan-
nels. Each channel is divided into GND, IN+, and IN- terminal cable
connectors (2 sets of 3 for each channel).
MIC OUT: 4-pin mini-Phoenix connector, divided into GND, OUT-, and OUT+
terminal connectors.
Video In BNCs: Feeds either Composite/S-Video Luma or S-Video Chroma signals into
the NXA-AVB/ETHERNET. This feed is then redirected out to a Modero
panel through the front Audio/Video CAT5 port.
ETHERNET: RJ-45 connector routes data to the G4 touch panel through the front
Ethernet port. These connections use a standard CAT5 Ethernet cable
to provide communication between the target touch panel, Breakout
Box, and NetLinx Master.
PWR: 2-pin mini-Phoenix connector that connects to a PSN power supply.
This port can be used to provide power to a Modero panel by sending it
through the NXA-AVB/ETHERNET (rear power connector through to
the front power connector).
Power In
(front)
Ethernet (to panel)
Audio/Video
Power (to panel)
S-Video Chroma
Composite/
Mic Out
Audio
In
Ethernet In
S-Video
Luma
(rear)
(to panel)
NXA-AVB/ETHERNET
Breakout Box
Ethernet
(RJ-45)
Comp/Y (BNC)
C (BNC)
Audio In - Left Channel
(6-pin captive wire)
Audio In - Right Channel
(6-pin captive wire)
GND
In (-)
In (+)
GND
In (-)
In (+)
GND(-)
Out (-)
Out (+)
Microphone Out
(4-pin captive wire)
Power
Ethernet Out
(CAT5)
Audio/Video
(CAT5)
Power to
touch panel
F
R
O
N
T
R
E
A
R
supply
FIG. 5 Wiring the rear AUDIO IN and MIC OUT for use with Unbalanced Audio
FIG. 6 Wiring the rear AUDIO IN and MIC OUT for use with Balanced Audio
FIG. 7 Sample System Settings page
Unbalanced
IN
GND
IN-
IN+
GND
IN-
IN+
Left Channel
Right Channel
(Jumper IN- to GND)
Unbalanced
OUT
GND
OUT-
OUT+
Microphone
Unbalanced
IN
(Jumper IN- to GND)
AUDIO IN
MIC OUT
Balanced
OUT
GND
OUT-
OUT+
Ground signal
Return signal
Line signal
Panel’s connection
information
NetLinx Master’s
connection information
  • Page 1 1
  • Page 2 2

AMX modero NXT-CV10 Quick start guide

AMX
Brand
AMX
Model
modero NXT-CV10
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents