Convair ClimateMaster CM9RW Owner's manual

Brand: Convair

Model: ClimateMaster CM9RW

Category: Mobile air conditioners

Type: Owner's manual

This manual is also suitable for

Instruction Manual

ClimateMaster CM12RW

CM12RCW, CM12RCS

ClimateMaster

Portable Refrigerated Air Conditioner

Waste electrical products must not be disposed of with

household waste. This product should be taken to your local

recycling centre for safe treatment.

Please read these instructions prior to using the

appliance and save them for future reference.

CONTENTS

Introduction......................................1

Safety ..............................................2

Component location.........................3

Installing the exhaust hose ..............4

Control panel ...................................5

Remote control ................................6

Operation.........................................7

Functions......................................8-9

Maintenance ..................................10

Troubleshooting .............................11

Specifications ................................12

THANK YOU for choosing a Convair

Air Conditioner. This appliance has

been carefully engineered to bring

you trouble-free personal air

conditioning. Please read this

manual carefully so that you take

full advantage of the many benefits

your Convair provides.

This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction in

using the appliance by a person

responsible for their safety.

Children should be supervised to

ensure that they do not play with the

appliance. Do not place anything

through the ventilating slots.

Your Convair cooler is a portable air

conditioning unit that supplies

refrigerated air to a personal area

within a room. It is not intended to

function as a house or room air

conditioner.

Be sure the appliance has been

securely and correctly installed

ac cor di ng to the ins ta l la ti on

instructions contained within this

manual.

Personal Cooling

Energy Saving Tips

Do not locate the air conditioner

where furniture or other objects can

obstruct the air flow.

Keep curtains and blinds closed

during the hottest part of the day.

Keep the filter clean.

Set the air conditioner to maximum

cooling and high fan speed initially,

then adjust to a comfortable setting.

Do not wait until the room is

excessively hot before using the air

conditioner.

INTRODUCTION

General Safety

Transport the air conditioner in an

upright position only, or leave it in an

upright position for at least 2 hours

before use (Fig 1).

Electrical Safety

For indoor use only.

Use only in the upright position on a flat

level surface and at least 50cm from any

objects.

Do not place objects on the air conditioner

or restrict air inlets / outlets (Fig 2).

Closely supervise any children and pets

when the air conditioner is in use.

Ensure the appliance has been installed in

acco rdance with nationa l wiring

regulations.

Do not store or operate the appliance near

any flammable substances.

During operation, water will collect in the

bottom tank of the air conditioner. Be

careful when moving the unit to prevent

water from spilling.

Electrical Safety (cont)

Caution! before connecting the

electrical power cord to a power outlet,

check that the air conditioner voltage is

the same as your power supply (refer to

the rating label located on the back of the

unit). Ensure the power supply is correctly

earthed and rated.

Plug the air conditioner directly into a

properly installed power outlet. Never use

an extension cord, double adaptor or multi

power outlet board to run this air

conditioner.

Do not pull the unit along by the power cord

or place the power cord near a source of

heat. Always unroll the power cord

completely before use.

If the power cord is damaged, in order to

avoid a hazard it must be replaced by an

electrician or similarly qualified person or

service agent.

Switch off and unplug when not in use.

Do not use in humid environments such as

bathrooms or other steamy or wet areas.

Do not touch or operate the air conditioner

with wet or damp hands or when standing

barefoot.

SAFETY

COMPONENT LOCATION

Air outlet

Handle

Remote

Sensor

Control panel

Air Filter

Air Intake

Power cord

Air Intake

Exhaust

Air Outlet

Drain

Rating

Label

OSC

Mode Temp Speed

On / OffTimer

OSC

Remote

Control

Exhaust Hose

Window Kit

Exhaust

Fitting

(cooler end)

Exhaust

Fitting

(window

end)

Drain

Tray

50cm

Assembling the exhaust hose (Fig 5)

Step 1:

Step 2:

Installing the exhaust hose to the air

conditioner (Fig 6).

Step 1:

Step 2:

Installing the exhaust hose to the

window (Fig 6).

Step 1:

Step 2

Fit the square exhaust fitting

onto the hose end with the 2 ‘pips’. The

pips will lock into the holes.

Fit the oblong exhaust fitting

onto the other end of the hose.

Position the square exhaust

fitting above the grooves on the exhaust

air outlet, with the open end facing down.

Push the hose fitting down into

the outlet until it is completely covered.

Snap the oblong connector into

position on the window attachment.

: Open the window and fit the

adjustable window attachment. Extend

the attachment as required and lock into

place with the wing nut. Ensure the outlet

is not obscured. The window attachment

can be installed horizontally or vertically,

depending on the window type.

Note!

The minimum distance required

from the operating air conditioner to

any obstructing objects or walls is

50cm (Fig 6).

Keep the exhaust hose as short and

straight as possible and minimise

kinks. This will maximise the cooling

performance.

Don’t use extension pieces for the

exhaust pipe as this will reduce the

cooling performance.

Hot air and possibly mist will be

emitted from the exhaust hose.

It is critical to the cooler’s

performance that the hot exhaust air

is completely removed from the space

being cooled.

hole

locating

pip

INSTALLING THE EXHAUST

TEMP/TIME

ON / OFF

OSCOSCTIMERSPEEDMODE

AIR SWEEP

AIR FRESH

SET TIME

COOL

HEAT

DRY

AUTO

Power ON / OFF button

Fan Speed

control button

Negative Ion

Indicator

Sweep Indicator

(Horizontal)

Sweep Indicator

(Vertical)

Fan Speed

Indicator

Dry Mode

Indicator

Auto Mode

Indicator

Timer Duration

Indicator

Temperature

Display

Heating Mode Indicator

(only CM12RCW &

CM12RCS)

Cooling Mode

Indicator

Timer Set

button

Horizontal Swing

Vane button

Vertical Swing

Vane button

Mode Select

button

Press to turn the air

conditioner on and off

Press to cycle the fan

speed between low,

medium and high

Press to enter the

timer setting mode

Press to start or stop

the outlet vanes sweeping

from side to side

Press to start or stop

the outlet vanes sweeping

up and down

Press to cycle from Auto,

Heat, Fan, Cooling and

Dry modes.

Temperature & Timer adjust button

Press to increase, to decrease

the set temperature or timer

To avoid damage to the control panel, do not operate with sharp objects.

NOTE!

CONTROL PANEL DISPLAY

CONTROL PANEL

OSC

Mode Temp Speed

On / OffTimer

OSC

If there are two of the same air

conditioners installed, they cannot be

controlled separately. When you operate

either remote, it will turn on both air

conditioners if they are both within signal

range (6 metres).

Don’t let the remote control drop onto hard

surfaces or be subjected to sudden

shocks in any way. The warranty does not

cover misuse or accidental damage.

Don’t place the remote control in direct

sunlight, or near extremes of temperature.

This will affect the control’s temperature

reading.

Don’t allow the remote control to get wet.

Don’t place near strong electromagnetic

waves.

Don’t mix old and new batteries ! If the

remote control will not be used for a long

time, remove the batteries to avoid

corrosion.

Care of your remote control

Preparation before operation

During Operation

Remove the battery cover and insert new

batteries

If there is no display, or only part display,

remove the batteries and replace with new

ones. If this does not solve the problem

contact your nearest service centre for

advice.

(AAA), making sure the + and -

are matching the compartment markings

(Fig 10)

If the display disappears, or the remote

control will not operate the air conditioner,

the batteries may need to be replaced.

(

Note! he air conditioner must be

plugged in and switched on for the

remote control to operate the air

con itioner. To use, point at the signal

receiving wi dow on the front panel and

press the remote but on. The air

conditioner will “beep” when a signal

has been received. If there is no beep,

press the remote button again, ensuring

it is within range 6 metres) of the air

conditioner.

NOTE:

WASTE BATTERIES SHOULD

BE DISPOSED OF CORRECTLY

Signal

transmission point

Display area

Mode Select

button

Temperature /

Timer adjust buttons

Timer button

Sweep button

(horizontal)

Sweep button

(vertical)

Fan Speed

adjust button

Power ON / OFF

button

Battery

compartment

Battery cover

REMOTE CONTROL

Starting the air conditioner

Step 1: Ensure the cooler is plugged in and

switched on.

Step 2:

Step 3:

Step 4:

Step 5:

Press the ON/OFF button on the

remote control or ON/OFF button on the

control panel to start the air conditioner.

Press the MODE button on the

control panel or MODE button on the

remote control to select the desired

operating mode (Fig. 11):

Press / on the control panel

or on the remote control to select the

desired temperature.

Do not set the cooling temperature too

low. This will consume more power. 24°C is

the recommended set temperature, with

high fan speed.

Changing the set temperature will

have no effect in FAN or DRY modes.

Press the SPEED button on the

control panel or the remote control to adjust

the fan speed. Each press will cycle the fan

speed as below:

Low speed

Medium speed

High speed

In Dry mode, the fan will always be

set to low speed. In heating and cooling

modes, the fan may automatically change

to high speed to protect the refrigeration

system.

In Cooling mode, the fan will continue

to run even when the compressor has

cycled off.

Auto mode

Heating mode

Fan mode

Cooling mode

Dry mode

- automatic selection of

operating mode

- reverse cycle heating

- Fan only operation (no

cooling)

- refrigerated cooling

- refrigerated moisture

removal from the air

r s

The temperature set range is 16°C-31°C

Tip

Note!

Note

Note!

Step 6:

Do not attempt to move the

motorised vanes by hand !

Important !

The air conditioner has 2 sets of

motorised air direction vanes. Press

the OSC buttons on the control panel or the

remote control to turn the vanes on or off.

operates the horizontal vanes - air

will sweep from side to side (Fig 12)

operates the vertical vanes - air will

sweep up and down (Fig 13)

Press the buttons again to stop the sweeping

vanes.

The cooler will store the last mode

selected in memory and return to this when

next switched on.

During cooling and heating

mode, water will collect in the air

conditioner’s tank. In cooling mode this

water is recirculated and some will be

exhausted out with the hot air, but will slowly

fill up the tank. This occurs more quickly in

humid conditions. In heating mode there is

no recirculation. If the tank should fill, error

code “E2” will appear on the control panel,

the unit will ‘beep’ 10 times and then shut

down. Refer to the Maintenance section for

draining the tank should this occur.

Note!

Step.2

Step.5

Step.3

Step.4

Step.6

OSC

Mode Temp Speed

On / OffTimer

OSC

OPERATION

OSC

Mode

Temp

Speed

On / Off

Timer

OSC

Timer Function - Remote Control

setup

Setting the OFF time

Step 1: ON

0.0

Step 2:

The air conditioner is fitted with a timer

function. This can be set so that the air

conditioner is operating before you wake

up, or to be cooling when you get home

from work, up to 12 hours in advance. To

use this function, the cooler must be

plugged in and ready to operate.

(Fig 14)

With the air conditioner ,

press the TIMER button on the remote

control. The display will show in the

bottom LH corner.

Press the TEMP/TIMER button to

adjust the time in 0.5 hour increments

from 0.5 - 12 hrs

(Fig 14 shows the cooler

will turn off after 2.5 hrs)

When the air conditioner is

working, only the TIMER OFF can be set.

When the air conditioner is off, only the

TIMER ON can be set.

(Fig 15)

With the air conditioner ,

press the TIMER button on the remote

control. The display will show in the

bottom LH corner.

Press the TEMP/TIMER button to

adjust the time in 0.5 hour increments

from 0.5 - 12 hrs (Fig 15 shows the cooler

will turn on after 3.5 hrs).

Remember to have the remote

control within range of the air conditioner.

The cooler will “BEEP” with each button

press.

Pressing the TIMER button after it

is set will cancel the TIMER.

Note

Note!

Setting the ON time

Step 1: OFF

0.0

Step 2:

Step.1

Step.2

FUNCTIONS

How to cancel the timer

0.0

Setting the timer at the cooler

SET TIME

Self check function

To cancel the timer, press the TIMER

button when either the TIMER OFF or

TIMER ON has been set. The SET TIME

will revert to and will disappear after 5

seconds.

Follow the same setting procedures as

above, for both TIMER OFF and TIMER

ON functions, by pressing the TIMER

button on the control panel.

and the timer durations in hours will be

displayed. Adjust by pressing the

TEMP/TIMER button to increase or

decrease in 0.5 hr increments.

To cancel the TIMER, change the SET

TIME to 0.0 h - after 2 seconds the SET

TIME will disappear.

The air conditioner incorporates its own

self diagnostics. The following table

shows the code and problem.

Code Problem

E2 Water tank is full (cooler will ‘beep’ 10

times to alert you) - refer maintenance

section for draining the tank

E3/E4/ Refrigeration pipe is damaged - contact a

E5 service centre for repair

Indoor temperature or coil sensor is

damaged - contact a service centre for

repair

FUNCTIONS

Draining the Air Conditioner

! Always replace the drain plug

immediately after draining.

To drain the air conditioner, place it over a

drain, or under

the drain point before removing the drain

plug, as the water will flow out as soon as the

plug is removed.

Remove the plug at the bottom front of the

appliance and allow the tank to completely

drain (Fig 16B).

put the drain tray (provided)

Note

End of season storage

Always disconnect the air conditioner from the electrical mains before cleaning

or draining.

To maximize the efficiency of the air conditioner, clean regularly.

Cleaning the housing

Cleaning the filter

Note! Never operate the air conditioner without the filter.

Use a soft, damp cloth to wipe the body clean.

Never use aggressive chemicals, spirits, detergents, chemically treated cloths, or

other cleansing solutions. These substances could possibly damage the cabinet

Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt and then

rinse thoroughly under running water (no hotter than 40°C).

Dry thoroughly before replacing.

Remove the filter as shown (Fig 16A).

Drain any water from the unit.

Operate the unit in ventilation only mode for a few hours, so as to

thoroughly dry the inside of the cooler.

Clean or change the filter.

Replace in the original carton or cover for storage.

Unplug and carefully store the power cord and plug end.

Push down on the

2 top tabs and pull

outwards to release

the air filter

MAINTENANCE

Never try to dismantle the air conditioner yourself.

Problem Check

The air conditioner does

not run.

Is the air conditioner plugged in ?

Is there a power failure ?

Is the "WATER FULL" error code “E2” flashing?

Drain the tank as shown (Fig 16).

Is the room temperature below the set temperature ?

The air conditioner has little

effect (firstly ensure that the

room being cooled is not too

large for the stated capacity

of the air conditioner).

Is there direct sunshine ? Remember to close

curtains or blinds.

Are windows or doors open ?

More people in the room will generate more heat.

Is there something in the room producing excessive

heat ?

Is the exhaust fitted correctly or obstructed ? All

exhaust air needs to be completely removed from

the room.

The air conditioner is not as

cool as it once was.

Is the filter dusty or dirty, restricting the airflow ?

Is the air inlet or outlet blocked ?

Is the room temperature below the set temperature ?

The air conditioner is too

noisy.

Is the air conditioner positioned unevenly, so as to

create vibration ?

Is the floor beneath the air conditioner uneven ?

It is possible that the overheat protection for the

compressor is on. Wait for it to reset.

Note: when changing between different modes

(cooling to fan or heating mode etc) the compressor

will turn off. A 3 minute delay will occur before the

compressor will turn on again.

The compressor will not run.

In case of problems that cannot be fixed by using the above guide,

or if service on your air conditioner is required, please contact your

dealer or designated service agent.

TROUBLESHOOTING

As a policy of continual product improvement, this manual, its contents and specifications are subject to change without notice.

SEELEY INTERNATIONAL - CLIMATEMASTER

PORTABLE AIR CONDITIONER

ClimateMaster CM12RW

ClimateMaster CM12RCW

ClimateMaster CM12RCS

Personal Cooling Personal Cooling & Heating

3,500 (12,000 Btu/hr) 3,500 (12,000 Btu/hr)

- 3,500 (12,000 Btu/hr)

2.5 2.5

310 310

£ 52 £ 52

220-240 V ~, 50 Hz 220-240 V ~, 50 Hz

1300 1350

6 6.2

3.15 A / 250V 3.15 A / 250V

R407C / 0.61 R407C / 0.61

2.7 2.9

0.6 0.7

IPX0 IPX0

40 40

445 / 350 / 870 445 / 350 / 870

Model

Function

Cooling Capacity (Watts) †

Heating Capacity (Watts) †

Dehumidifying Capacity (L/hr)

Air Flow Volume (m / hr)

Noise Level - Sound Pressure (dB(A))

Power Supply

Input Power (Watts)

Input Current (Amperes)

Fuse Type

Refrigerant Type / Charge (kg)

High Side Pressure - Maximum (MPa)

Low Side Pressure - Maximum (MPa)

Water Ingress Protection Rating

Weight (kg)

Dimensions (mm)

(width / depth / height)

†Based on manufacturer's test results using the Air Enthalpy method

SPECIFICATIONS

3-PIN

SUPPLY

PLUG

- - - REVERSE CYCLE ONLY

PIPE

ROOM

COMPRESSOR

WIRING DIAGRAM

CONTROL PANEL

7 WIRE

LOOM

CONDENSOR

FAN

8 WIRE

LOOM

EVAPORATOR

FAN

PUMP

WAY

REMOTE

CONTROL

SENSOR

3 WIRE

LOOM

SWING

MOTOR

(HORZ)

5 WIRE

LOOM

SWING

MOTOR

(VERT)

5 WIRE

LOOM

NOTES

133003-E

1112

Service

Australia 1-300-650-644

seeleyinternational.com

It is the policy of Seeley International to introduce continual

product improvement. Accordingly, specifications are

subject to change without notice. Please consult with your

dealer to confirm the specifications of the model selected.

133010-E

seeleyinternational.com

AU 1112

Convair ClimateMaster CM9RW Owner's manual

Brand: Convair

Model: ClimateMaster CM9RW

Category: Mobile air conditioners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Convair ClimateMaster CM9RW Owner's manual

This manual is also suitable for

Convair ClimateMaster CM9RW Owner's manual

Related papers

Other documents