www.wildviewcam.com
TollFree888‐304‐6125
9
3. TurnthecameratotheONposition.
4. The camera will automatically switch to external power when it is
connected,eveniftheinternalbatteriesareinstalled.
NOTE: Please make sure the voltage and polarity (+/‐) are correct before
connection. Incorrect voltage or polarity (+/‐) will damage the camera.
When both internal and external batteries are connected, the camera will
drawpowerfromthehighervoltagesourcefirst.
MemoryOptions
The camera is also equipped with an expandable media card slot capable of
accepting up to 16GB* SD card with Class 6 or below speed rating (sold
separate ly).Withnomemorycardinsertedintotheslot,thecamerawilluse
thebuiltinSDRAMmemorytostoreimages.IfanSD
cardisinsertedintothe
slot, then the camera will bypass the built in memory and utilize the SD
memory. The front counter display will show the number of images in the
builtinmemory,unlesstheexpansioncardisinsertedatwhichpointthefront
counterwillonlydisplay
thenumberofimagesstoredintheexpansioncard.
WARNING: The above camera will not accept Class 10 or above speed
ratin
SD memor
cards.
www.wildviewcam.com
TollFree888‐304‐6125
10
InsertingSDmemorycard
NOTE: Make sure camera is in the OFF position whenever adding or
removingmemory.
• Insert SD memory card in to the SD card slot completely and in the
correct direction, as shown by the picture shown on the Open View
imageabove(seepage5).
• To remove the SD memory card, depress the SD card and pull out the
cardgently .
• SD
cardsmust be clean(noimagesfromothersources).If you areusing
theSDcardfromothercameras,pleasemakesuretoformattheSDcard
inyourcomputerpriortouseinthecamera.Newcardsaregoodtouse
straightfromthepackage.
• IfinstalledSD
cardislocked,camerawillshowLOConthedisplay,please
slidethelockswitchtounlocklocationthenreinstalltheSDcard.
FORMAT – Definition: When you format a SD memory card, the operating
systemerasesallinformationandfilesonthecard.Thenitcreatesaninternal
address tables
that it later uses to locate information and files. Formatting
also removes all Hidden System files as well. Basically it cleans your SD
memory card just like if it was brand new. Please make sure to follow the
guidelineslistedbelow:
SDCardsize:2GBorbelow,formatusingFile
Systemtype“FAT”.
SDCardsize:4GBorabove,formatusingFileSystemtype“FAT32”.
*DO NOT use File System type “NTFS” or “exFAT”, these formats are not
supported.
www.wildviewcam.com
TollFree888‐304‐6125
11
SETUPANDPROGRAMMING
Whenthecameraisfirstturnedon,theinternalLCDscreendisplaysthe
camerastatus.Thefollowinginformationispresentonthisscreen.
Definitions
• Cam:Tosetwhichmodeyouwantthecameratobein.
¾ TEST=Testmode
¾ OFF=PowerOffmode
¾ ON=ActivePassiveInfraredmode/PowerOnmode
• Time out: To set the amountoftimethecamerawillsleep between PIR
triggering.
¾ 20s=20Seconds
¾ 1m=1minute
¾ 5m=5minutes
¾ 10m=10minutes
• Resolution:Theresolutionselectionthatyouhavechosen.
¾ High(HI)=8.0Megapixels(Imageinterpolatedfrom5MSensor)
¾ Low(LO)=5.0Megapixels
www.wildviewcam.com
TollFree888‐304‐6125
12
• Video:Setsthelengthoftimehowlongyouwanttocapturevideo.
¾ 15s=15seconds
¾ 30s=30seconds
¾ 60s=60seconds
• Burst:Tosetthenumberofpicturesorvideolengththecamerawilltake
perPIRtriggering.
¾ 1P
=Singlestillimagecapture dperPIRtriggering.
¾ 3P=Threecontinuousstillimagescaptur edperPIRtriggering.
¾ 6P=Sixcontinuousstillimagescaptur edperPIRtriggering.
¾ VIDEO = Places camera in Video mode and will capture video per
settingabove.
• DayandTime:Displaysthe
dateandtimethatyou’veset,onallstill
images.ForVideo,itwillappearonthefirstframe.(UsingQuickTime
PlayerorWindowMediaPlayer).
• Moonphase: Displaysthemoonphase.ForVideo,itwi llappearon the
firstframe.(UsingQuickTimePlayerorWindowMedia
Player).
• FULL: When the external memory capacity reaches full, the front LCD
screenwillshow“FULL.”
• IR Range Control: This allows you to control how many emitters are
activatedpertriggeringdependingonyourneed.
¾ 35IR–Fullillumination.Idealforsubjectmatterbeyond20ft.
¾ 25
IR–Reducedillumination.Goodforusewhensubjectis20ftor
closer.