Solight 1L56 User manual

1L56
Solight
Brand
Solight
Model
1L56
Type
User manual

This manual is also suitable for

Solight 1L56 wireless doorbell offers a range of melodies and adjustable volume levels. It features a waterproof transmitter suitable for outdoor placement and a learning code function to pair multiple bells with one button or vice versa. The doorbell operates at 433MHz with a range of up to 120m in open areas. Easy to install with self-adhesive pads or screws, it's a convenient solution for your home.

Solight 1L56 wireless doorbell offers a range of melodies and adjustable volume levels. It features a waterproof transmitter suitable for outdoor placement and a learning code function to pair multiple bells with one button or vice versa. The doorbell operates at 433MHz with a range of up to 120m in open areas. Easy to install with self-adhesive pads or screws, it's a convenient solution for your home.

Dear customer, thank you for purchasing our product. Please read the following instructions carefully and follow them to serve you safely
and to your full satisfaction. This will prevent misuse or damage. Avoid unprofessional handling of this appliance and always observe the
electrical appliance usage guidelines. Keep the instruction manual carefully. For use in the home or indoors. This product should only be used
by an adult. Never expose to environments with high humidity (e.g. bathroom), avoid contact of the product with liquids.
Description:
Note: The doorbell operates at a frequency of 433MHz. The range is max. 120m in open area.
Inserting batteries into the transmitter
Grasp the nameplate and battery cover with two fingers and pull it open. Insert a 12V/23A alkaline battery.
Observe the marked polarization. Close the cover.
Transmitter and receiver location
Before fixing the transmitter, make sure that the doorbell is working properly by plugging the receiver into the socket (AC 230V) where you
want to use it and then pressing the button on the transmitter where you want to fix it. Choose a position where the transmitter is clearly
visible, i.e. on or near the door frame, about 1.5m above the ground. As the transmitter is waterproof, it can be placed outdoors if necessary.
However, prefer a location that protects the transmitter from water and excessive heat. Mounting on a door frame is easier as the transmitter
can simply be screwed to the wood with the back wall,
Doorbell control
To select the melody, use the button as shown in the picture. Press the button to play and change individual melodies. The selection is
automatically saved when playback is finished.
The volume is controlled by the volume change button as shown. When the button is pressed, the current melody is played at the selected
volume level. You can adjust the volume in three levels.
"Learning code" function
The "Learning code" function allows you to pair several bells and buttons into one group. This allows several buttons to ring
one bell or one button to ring several bells (max. 4).
If you need to assign a new transmitter to a receiver, do the following:
- Press and hold the volume button on the doorbell while pressing and holding the button on the transmitter.
- When the tune "Dong Dong" sounds, release the button on the bell, and a second later release the button on the transmitter.
This assigns the transmitter to the receiver. The original transmitter is also assigned. Shown in Figure 1. You follow a similar procedure to
assign a new receiver to a transmitter. All previously paired receivers are also assigned to a transmitter. Shown in Fig. 2
Unpairing the button from the receiver
EN 1L56, 1L56B
Wireless doorbell
Pairing and volume
button
Bell button
with LED ring
indicator
Mounting
hole
Cover for
nameplate
and battery
Self-adhesive
pads
Mounting
hole
Rear cover opening
latch for wall
mounting
Button to
change the
melody
LED
Transmi
Transmi
Receiver
If you have multiple transmitters paired to your receiver, you may need to unpair one of the transmitters. To unpair, follow these steps:
- Press and hold the button to change the bell volume, after three seconds you will hear the melody "Dong Dong", keep holding the
button until you hear the ringing again.
Figure 1:
Figure 2:
Solving possible problems
If the receiver does not ring repeatedly after pressing the button on the transmitter, check:
- battery capacity in the transmitter and receiver. The battery may have been discharged prematurely.
- whether the distance between the transmitter and the receiver is too large.
- there are no strong sources of signal interference between the transmitter and receiver (radio and wireless networks, large metal
objects, reinforced concrete walls, etc.).
If you have any problems, please contact your dealer.
Solight Holding s.r.o. declares that the product complies with the requirements and provisions of Directive 2014/53/EU. The equipment can
be operated freely in the EU. The product can be operated under general authorisation No. VO-R/10/05.2014-3. The Declaration of
Conformity can be found at www.solight.cz.
Producer: Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, www.solight.cz
Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, Czech Republic.
Transmitt
Receiver 1
Receiver 2
Receiver 3
Receiver 4
  • Page 1 1
  • Page 2 2

Solight 1L56 User manual

1L56
Solight
Brand
Solight
Model
1L56
Type
User manual
This manual is also suitable for

Solight 1L56 wireless doorbell offers a range of melodies and adjustable volume levels. It features a waterproof transmitter suitable for outdoor placement and a learning code function to pair multiple bells with one button or vice versa. The doorbell operates at 433MHz with a range of up to 120m in open areas. Easy to install with self-adhesive pads or screws, it's a convenient solution for your home.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents