Rugged Ridge Pocket Island Topper Installation guide

Type
Installation guide

This manual is also suitable for

Jeep® JK Wrangler Summer Top ( 4dr )
Contents:
1. Summer Top
Page 1 of 3
Caution - This product is designed to enhance the appearance of the vehicle and to shield the
occupants from ordinary weather conditions, DO NOT rely on product to contain occupants
within the vehicle, or to protect against injury or death in the event of an accident. This
top will not protect the occupants from falling objects. Never operate vehicle in excess of
manufacture’s specification. SEAT BELTS ARE TO BE WORN AT ALL TIMES.
(Step 1) - Insert windshield header into top as shown. This top will work with most aftermarket (JK)
headers. Brand of aftermarket header should not affect fitment.
Before installing Summer Top read installation instructions. Failure to do so may result in a poor tting top
and could place occupants in a potentially dangerous situation. After installation of summer to, check to
make sure it has been properly secured before driving.
(Step 2) - Place header and top onto windshield channel. Follow manufactures installation instructions for
header.
(Step 3) - Place summer top over center roll bar and loop center swivel hooks around the back side of
speaker bar. Push swivel hooks up into center roll bar (Freedom top mounting holes). Do Not
tighten straps at this time. Pull straps tight enough to only keep top in place.
(Step 1) (Step 2) (Step 3)
Part Number: 13579.XX, 13589.XX
Part Number: 13579.XX, 13589.XX
Jeep® JK Wrangler Summer Top ( 4DR)
Page 2 of 3
(Step 4) - Wrap rear summer top straps over top of rear roll bar cross member and loop through plastic
buckles as shown Pull straps snug. Do Not tighten at this time.
(Step 5) - Place side strap plastic hooks into body tub as shown. Pull straps snug. DO NOT tighten
at this time.
(Step 6) - Loop rear swivel hook straps under seat belt mounting brackets located on rear roll bar. Pull
hooks and straps back over roll bar and secure to elongated holes located on body tub as
shown. Pull straps snug. DO NOT tighten at this time.
(Step 7) (Step 8) (Step 9)
(Step 4) (Step 5) (Step 6)
(Step 8) - Loop Velcro side straps around and under door surrounds.
(Step 7) - Pull straps up between surrounds and side of roll bar. Pull strap around roll bar and secure
back to strap as shown. Front (header strap) should be pulled under front plastic trim.
(Step 9) - Center straps (with buckle) are secured around center post (B-pillar). Pull straps around post
just above plastic trim. Pull strap tight.
Jeep® JK Wrangler Summer Top ( 4DR)
Page 3 of 3
(Step 10) - Secure roll bar flaps as shown. Flaps have been designed to work with roll bar grab handles.
Grab handles should be positioned between flap cutouts.
.
(Step 12) (Step 13) (Step 13)
(Step 10) (Step 10) (Step 11)
(Step 12) - For vehicles without plastic door surrounds follow steps 1-6 as described. Steps 7 & 8 are
not used. Side Velcro straps are to be pulled under roll bar as shown.
(Step 13) - Pull Velcro strap over top of roll bar and twist so that Velcro face can be secured to front
side of strap as shown. Pull side straps down to body tub and tighten.
(Step 14) - With all Velcro straps secured proceed with steps 9-11.
NOTE: Summer tops have been designed to work best with full door surrounds installed. Summer tops
installed to vehicles without surrounds may not fit as tight. This is normal.
(Step 11) - With all side Velcro straps secured go back and tighten sound bar straps, side body tub hooks
and rear swivel hook straps. Pull tight until top is smooth.
Installation Instructions - Vehicles Without Plastic Door Surrounds
Part Number: 13579.XX, 13589.XX
  • Page 1 1
  • Page 2 2
  • Page 3 3

Rugged Ridge Pocket Island Topper Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI