Genius P633 Owner's manual

Category
Security cameras
Type
Owner's manual
English
-1-
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the
FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the
manual. If such changes or modifications should be made, you could be required to stop
operation of the equipment.
READ THIS FIRST
1. Product design and specifications are subject to change without notice. This includes primary
product specifications, software, software drivers, and user’s manual. This User Manual is a
general reference guide for the product.
2. The product and accessories that come with your camera may be different from those
described in this manual. This is due to the fact that different retailers often specify slightly
different product inclusions and accessories to suit their market requirements, customer
English
-2-
demographics, and geographical preferences. Products very often vary between retailers
especially with accessories such as batteries, chargers, AC adapters, memory cards, cables,
carrying cases/pouches, and language support. Occasionally a retailer will specify a unique
product color, appearance, and internal memory capacity. Contact your dealer for precise
product definition and included accessories.
3. The illustrations in this manual are for the purpose of explanation and may differ from the
actual design of your camera.
4. The manufacturer assumes no liability for any errors or discrepancies in this user manual.
5. For driver updates, you can check the “Download” section of our website,
www.geniusnet.com.tw.
WARNING
Do not use this camera if it is emitting smoke (or an unusual odor), if it becomes unusually
hot to the touch, produces a peculiar noise, or exhibits any other abnormal conditions.
Operating the camera in any of these circumstances may cause a fire or an electrical shock.
Stop using the camera immediately, turn the camera off and remove the battery. Contact your
dealer or authorized service facility for repairs. Never attempt to repair this camera by
yourself, as this may be dangerous.
Do not expose the camera to moisture and make sure no water gets into the camera. Take
particular care when using the camera under extreme weather conditions, such as rain or
snow, or when operating the camera at the beach or near water. Avoid using this camera in
places subject to extreme moisture. Do not use the camera if water has entered the camera.
Turn the camera off and remove the battery. Contact your dealer or authorized service facility.
Do not continue to use the camera as this may cause a fire or an electrical shock.
Do not use the camera if any foreign objects have entered the camera. Turn the camera off
and remove the battery. Contact your dealer or authorized service facility. Do not continue to
use the camera as this may cause a fire or an electrical shock.
Do not place the camera in an unstable location such as on a wobbly table or sloping surface
where the camera may fall or tip over and cause injury. If the camera has been dropped or
damaged, turn the camera off and remove the battery. Contact your dealer or authorized
service facility. Do not continue to use the camera as this may cause a fire or an electrical
shock.
Do not insert or drop metallic or other foreign objects into the camera through access points
such as the memory card slot. This may cause a fire or an electrical shock.
Do not attempt to modify this camera. Do not remove the camera casing. This may cause a
fire or an electrical shock. Internal inspection and repairs should only be carried out by an
English
-3-
authorized service facility.
Never operate this camera in any way while driving a vehicle. This may cause a traffic
accident.
CAUTION
Do not place this camera in a location affected by oil fumes or steam, such as near a cooking
stove or humidifier. This may cause a fire or an electrical shock.
Do not leave this camera in a location subject to extremely high temperatures, such as in a
sealed vehicle or in direct sunlight. Exposure to high temperatures may adversely affect the
camera case and internal components and may cause a fire.
Do not cover or wrap the camera with a cloth or quilt. This may cause heat to build up and
distort the camera case and cause a fire. Always use the camera and accessories in
well-ventilated locations.
Handle the camera carefully and do not expose the camera to shock or vibration. Handling
the camera roughly may cause a malfunction.
Do not use battery other than those specified for use with your camera. Use of unsuitable
battery may result in the battery splitting, or leaking and may cause a fire, injury, or soiling of
the battery compartment.
When placing the battery into the camera, check the polarity markings on the battery ( - and
+ ) to ensure that the battery is inserted correctly. Incorrect battery polarity will result in
camera inoperability and may result in the battery splitting or leaking and causing a fire, injury,
or soiling of the battery compartment.
Remove the battery if the camera will not be used for an extended period of time. The battery
may leak and cause a fire, injury or soiling of the battery compartment. If the battery leaks,
clean and wipe the battery compartment carefully and install a new battery. Wash your hands
carefully if you touch the battery fluid.
English
-4-
CONTENTS
INTRODUCTION 6-7
Overview
Package contents
GETTING TO KNOW THE
CAMERA
8-15
Front view
Rear view
Mode dial
Viewfinder LED indicators
LCD monitor information
GETTING STARTED 16-22
Attaching the Camera Strap
Inserting and Removing the Battery
Charging the Battery
Inserting and Removing the SD Card
Turning the Power On/Off
Formatting the SD Card
Choosing the Language
Setting the Date and Time
Setting Image Resolution and Quality
PHOTOGRAPHS MODE 22-35
Auto Photography Mode
Using the Optical Zoom
Using the Digital Zoom
Setting the Flash
Setting the Focus
Self-timer/Photographing at Intervals
Exposure Compensation/Backlight
Correction
Program (Automatic Exposure)
Photography Mode
Shutter Speed Priority
Photography Mode
Aperture Priority Photography
Mode
Manual Photography Mode
Setting the Scene Mode
Movie Mode
PLAYBACK MODE 36-45
Playing Back Still Images
Playing Back Video Clips
Playing Back Still Images/Video Clips on
a TV
Recording Voice Memos
Thumbnail Display
Zoom Playback
Slideshow Display
Protecting Images
DPOF Settings
Erasing Images
MENU OPTIONS 45-54
Photography Menu (Picture)
Photography Menu (Function)
Photography Menu (AE/AWB)
Playback Menu
Setup Menu (Basic)
Setup Menu (Custom)
TRANSFERRING RECORDED
IMAGES/MOVIES TO YOUR
COMPUTER
54-56
Step 1: Installing the USB Driver
Step 2: Connecting the Camera to Your
Computer
English
-5-
Step 3: Downloading Images and Video
Files
INSTALLING
Presto! Mr. Photo
56-57
INSTALLING
Presto! Image Folio
57
CONNECTING THE
CAMERA TO OTHER
DEVICES
58
CAMERA
SPECIFICATIONS
58-59
English
-6-
INTRODUCTION
Overview
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital pictures is fast and easy with this state-of-the-art smart camera.
Equipped with a 6.3 Mega pixel CCD, this camera is capable of capturing pictures with a
resolution of up to 2816 x 2112 pixels.
Other cool features provided by the camera include the following:
LCD monitor The 2.0" CG silicon color LCD monitor makes it easy to frame
your subject when taking pictures. It also displays the pictures
you have taken.
Recording medium External memory supports SD card up to 512MB.
Camera mode Variety of camera modes allows you to operate for your
preference and take photographs according to photographic
condition.
Optical zoom 3x optical zoom lens allows you to take telephoto and wide-angle
pictures.
Digital zoom 4.4x digital zoom and 3x optical zoom permit zoom photography
of up to 13.2 times; 2x and 4x playback captured images to
enlarge a selected portion of an image.
Flexible flash settings Change the flash setting according to your lighting environment
and photography mode setting.
Focus mode Photographs can be taken with the distance to the subject set by
auto focus, macro, infinity, 3 m, or 1 m.
Self-timer mode Time selectable between 2 seconds, 10 seconds, 10+2 seconds
and interval.
Still image capture Take different still images including single, a series of 3 images
with different exposures, and 5 images continuously.
Movie mode Record video clips with voice.
Voice memo A voice memo can be recorded for 5 seconds immediately
following still single image photography. Also it can be recorded
while viewing the picture in playback mode.
Camera settings Have more control over picture quality by adjusting the menu
options.
English
-7-
Thumbnail display Display in sets of nine pictures on the LCD for easier and quicker
selection of pictures.
TV and PC connection View pictures on a television monitor or computer while
connected to the USB or A/V cable.
DPOF settings Allow you to embed printing information on your SD card and to
print your images on a DPOF compatible printer by simply
inserting it.
Package contents
Carefully unpack your package and make sure that you have the following items. In the event
that any item is missing or if you find any mismatch or damage, promptly contact your dealer.
Digital camera USB cable
Video cable Software CD-ROM
User’s manual Camera strap
Quick guide Camera pouch
Two Rechargeable Lithium Ion
Batteries
A 32MB SD memory card
Rechargeable Lithium Ion Battery
Charger
Rechargeable Lithium Ion Battery
Charger Power Cord
AC Plug Adaptor for EU to US
NOTE
Accessory and components may vary by different retailer.
English
-8-
GETTING TO KNOW THE CAMERA
Front view
#
Name
Description
1. Self-timer LED
(AF auxiliary light)
Blinks red during Self-timer mode until picture is taken.
Effective for still image capture mode when the luminance
value of Auto and Macro focus mode is below 6.
2. Viewfinder window
Allows you to frame the subject of the picture.
3. Flash
Provides flash illumination.
4. Shutter button
Focuses and locks the exposure of the camera when
pressed halfway down, and takes the picture when
pressed all the way down.
5. Zoom lens
3X optical zoom lens allows you to take telephoto and
wide-angle pictures.
6. POWER button
Turns the camera power on and off.
7. MIC (Microphone)
Records audio clips.
8. Mode dial
Sets the camera mode.
9. DC IN 5V terminal
Allows you to connect AC power adapter to the camera to
operate the camera without battery, or to charge
rechargeable battery.
10. USB/A/V OUT terminal
Allows you to connect a USB cable or an A/V cable to the
camera.
English
-9-
Rear view
#
Name Description
1. Diopter adjustment dial Provides a more clear image when using the viewfinder.
2. Viewfinder window Allows you to frame the subject of the picture.
3. Viewfinder LED Displays the camera current state.
4.
(Zoom in) button
Zooms the lens to telephoto position.
(Zoom out) button
Zooms the lens to wide-angle position.
5. Speaker Produces camera sounds and plays recorded audio.
6. MENU button Toggles OSD menu on and off.
7.
(Display) button
Turns the LCD monitor display and live view on and off.
8. Strap holder Camera strap attachment.
9. Search dial Selects the next or previous picture in playback mode, or
changes the shutter speed or aperture value setting in
[Tv], [Av] and [M] modes.
10.
(Erase) button
Allows you to erase the picture.
11. Tripod socket Allows tripod mounting.
12. Battery/SD card cover Allows access to the battery and insert or remove the
memory card.
13. LCD monitor Provides menu information to operate the camera, and
previews the picture before taking it and review it
afterwards.
14. SET /Direction button Allows you to scroll through menus and pictures, and then
select choices.
English
-10-
SET /Direction button
# Name Description
1. SET button Enters the menu page and confirms the chosen
setting.
2.
button
Scrolls upwards.
3.
/ (Focus) button
Allows you to choose the appropriate focus
setting.
4.
button
Scrolls downwards.
5.
(Self-timer) button
Allows you to toggle the self-timer on and off,
selects the desired self-timer mode or choose
the interval photography.
6.
button
Scrolls left.
(Exposure compensation /
Backlight correction) button
Allows you to toggle the exposure compensation
/ backlight correction on and off.
7.
button
Scrolls right.
(Flash) button
Allows you to choose the appropriate flash
setting.
English
-11-
Mode dial
: photography mode
# Mode Description
1.
Auto photography
The camera is automatically sets for exposure, etc.
2.
Program (auto exposure)
This permits the shutter speed and aperture to be set
automatically and other factors to be set manually.
3.
Shutter speed priority
Selects this when you want to photograph with shutter
speed priority.
4.
Aperture priority
Selects this when you want to photograph with
aperture priority.
5.
Manual photography
Selects this when you want to manually set the
exposure, aperture and other settings.
6.
Portrait
Selects this when you want to photograph a person
and blur the background.
7.
Sports
Selects this when photographing fast-moving
subjects.
8.
Night scene
Selects this when photographing evening or night
scenes.
9.
Movie
Selects this when recording video clips.
10.
Set-up
Chooses your preferences on the camera’s settings.
11.
PC
Downloads the image to the personal computer.
12.
Playback
Performs image playback, deletion and writing of the
print information.
English
-12-
Viewfinder LED Indicator
This describes the color and state of the viewfinder LED.
Color State
During
power off
During
photography
During
playback
During
connection
to a PC
On
Battery
charging in
progress.
Auto focusing
successful.
(AF is locked)
-
While the
camera is
connected to
a PC.
Green
Flashing -
Self-timer in
operation at a
handshake
alarm.
- USB busy
On
-
Writing to SD
card in progress
Accessing of
SD card in
progress.
DPOF file is
being
created.
Accessing of
SD card in
progress.
Red
Flashing -
Auto focusing
failure
- -
On
Battery
charging
error.
Processing
image.
Flash charging
in progress.
Zoom
initialization in
progress.
-
Not
recognized
by the PC, or
other status.
Orange
Flashing -
No battery
power left.
Camera
malfunction.
No battery
power left.
No battery
power left.
No SD card.
English
-13-
LCD Monitor Icons
Photography mode [ ] [ ] [ ] [ ]
1. Mode icon
2. Focus icon
3. Unsteady hold warning icon
4. Zoom status
5. Focus area (When the shutter button is
pressed halfway.)
6. Voice memo
7. Remaining battery status
8. Flash icon
9. Image size
10. Quality
11. Capture mode icon
12. Self-timer icon
13. Possible number of shots
14. White balance icon
15. Metering icon
16. Backlight correction
17. Date and time
NOTE
Each press of the button switches one step in the sequence of Normal display
(displaying the icons, etc), display OFF, LCD monitor OFF.
English
-14-
Photography modes [ P ] [ Tv ] [ Av ] [ M ]
1. Mode icon
2. Focus icon
3. Unsteady hold warning icon
4. Zoom status
5. Focus area (When the shutter button is
pressed halfway.)
6. Voice memo
7. Remaining battery status
8. Flash icon
9. Image size
10. Quality
11. Capture mode icon
12. Self-timer icon
13. Possible number of shots
14. White balance icon
15. Metering icon
16. Exposure compensation
17. Shutter speed
18. Aperture
19. Histogram
20. Long time exposure mode icon
NOTE
Each press of the button switches one step in the sequence of Normal display
(display the icons, etc), Normal and Histogram display, display OFF, LCD monitor OFF.
English
-15-
Photography mode [ ]
1. Mode icon
2. Focus icon
3. Zoom status
4. Remaining battery status
5. Image size
6. Quality
7. Self-timer icon
8. Possible recording time/elapsed time
9. Recording indicator
Playback mode [ ]-Still Picture Playback
1. Folder number
2. File number
3. Voice memo icon
4. Protect icon
5. Mode icon
Playback mode [ ]-Video Playback
1. Folder number
2. File number
3. Protect icon
4. Movie status bar
5. Total time
6. Elapsed time
7. Play mode
8. Mode icon
English
-16-
GETTING STARTED
Attaching the Camera Strap
Attach the camera strap as shown in the illustration.
Inserting and Removing the Battery
We highly recommend using specified rechargeable lithium-ion battery to fully demonstrate this
camera’s function. Charge the battery before using the camera. Make sure that the power of the
camera is off before inserting or removing the battery.
1. Open the battery/SD Memory Card cover.
2. Insert the battery in the correct orientation shown.
Tilt the battery lock lever in the direction of the arrow and orient the battery so that its
label is facing to the front side of the camera, and then insert the battery.
3. Close the battery/SD Memory Card cover.
Removing the Battery
Open the battery/SD card cover and then release the battery lock lever. When the battery has
come out a little, slowly pull it out the rest of the way.
NOTE
Use only the specified battery type (Lithium Ion).
If you are not going to use the battery for an extended period of time, remove it from the
camera to prevent leakage or corrosion.
Never use different type of battery.
Avoid using battery in extremely cold environments as low temperatures can shorten the
English
-17-
LED INDICATION
battery life and reduce the camera performance.
Charging the Battery
AC INPUT
1. Insert the battery, noting correct polarity (+ and -).
Input Voltage:100-240V/50-60Hz
Output Voltage:4.2V/750mA
2. LED Indicator:
Status LED Indication Battery Charge Condition
Battery not installed Green OK
Battery installed Green Fully charged
Battery installed Red Charging
Battery installed/not
installed
Off Battery/charger defective
3. Notice:
A. Before you use a new battery, it should be charged for 3 hours the first time.
B. If the green LED is on when power is connected, it indicates the battery charger is
operating normally and ready for battery charging.
C. When the battery is put into the battery charger, the LED indicator changes from green
to red, indicating the battery is being charged.
D. If the LED indicator is not on when the power is connected, it indicates that the battery
charger is defective. The user should turn AC power off.
E. If the battery has been charged over 3 hours and the LED indicator is still red, this
means the battery is faulty. The user should remove the battery.
F. If it is necessary to charge a backup battery, the user should wait until the charging
battery is completely charged. Then remove the charged battery and charge the
backup battery.
NOTE
Never use the battery unspecified for the camera.
Do not place the camera in hot temperature. Use it at room temperature.
English
-18-
Inserting and Removing the SD Card (Optional)
Images photographed with this camera will be stored on the SD card. Without inserting the SD
card, you cannot take photographs using the camera. Before inserting or removing the SD card,
make sure that the power of the camera is off. You may also expand the memory capacity up to
512MB so that you can store additional images and video clips.
Inserting the SD card
1. Slide the battery/SD Memory Card cover in the direction of
the [OPEN] arrow.
2. Insert the SD card in the correct orientation shown.
Hold the SD card with its metal contact end surface
facing the rear side of the camera, and then insert the
card as far as it can go.
If the card cannot be inserted, check the orientation.
3. Close the battery/SD Memory Card cover.
Removing the SD card
Open the battery/SD card cover, press lightly on the edge of the SD card and it will eject.
NOTE
If the camera is powered-on without the card, the “NO CARD” message appears on the LCD
monitor.
To prevent valuable data from being accidentally
erased from an SD Memory Card you can slide the
write-protected tab (on the side of the SD Memory
Card) to “LOCK”.
To save, edit or erase data on an SD Memory Card,
you must unlock the card. MMC Card can not be
accepted to use.
Please format an SD Memory Card by this camera before use.
Turning the Power On/Off
Load the battery and insert an SD card before starting.
Turning the power on
Press the POWER button to turn the power on.
The viewfinder LED lights green and the camera is initiated.
When the power is turned on, the camera will start in the
mode that was set with the mode dial.
English
-19-
Turning the power off
Press the POWER button to turn the power off.
NOTE
The power is turned off automatically when the camera has not been operated for a fixed
period time. To resume the operation condition, turn the power on again. Refer to section in
this manual titled “Auto PoFF” in the Setup Menu (Basic) for further details.
After the power is turned on, it may take several seconds to charge the flash. While the flash
is being charged, the viewfinder LED lights orange, and then the camera is not yet ready for
photography. Start photography after the viewfinder LED is turned off.
Formatting the SD Card
This erases all of the images and folders that have been
recorded on the SD card. Formatting is not possible when the SD
card in the locked condition.
1. Set the mode dial to [
].
[Basic] of the set-up menu is displayed.
2. Select [Format] with the
/ buttons from [Basic] of the
set-up menu, then press the SET button.
3. Select [Execute] with the
/ buttons, and press the
SET button.
To cancel formatting, select [Cancel] and press the SET
button.
NOTE
You need to format an SD card before using it in this camera.
Formatting the SD card also erases the protected images. All data other than images are
also erased. Before formatting the card, make sure that all the images are unnecessary.
English
-20-
Formatting is an irreversible action and data cannot be recovered at a later time.
An SD card having any problem cannot be properly formatted.
Choosing the Language
When you first turn the camera on, choose a language for
displayed information on the LCD monitor.
1. Set the mode dial to [
] and press the button
[Custom] of the set-up menu is displayed.
2. Select [Language] with the
/ buttons and press the
SET button.
The Language setting screen will be displayed.
Select the displayed language using the / buttons and
press the SET button. The setting will be stored.
Setting the Date and Time
The date/time needs to be set if/when:
Camera is turned on for the first time.
Camera is turned on after leaving the camera without the
battery for an extended period of time.
When the date and time information is not displayed on the LCD
monitor, follow these steps to set the correct date and time.
1. Set the mode dial to [
] and press the button.
[Custom] of the set-up menu is displayed.
2. Select [Date/Time] with the
/ buttons and press the
SET button.
The Date/Time setting screen will be displayed.
3. Select the item’s field with the
/ buttons and adjust
the value for the date and time with the
/ buttons.
4. After confirming all settings are correct, press the SET button.
The setting will be stored and the screen will return to the
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

Genius P633 Owner's manual

Category
Security cameras
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI