Lifetime 151110 Owner's manual

11/23/2011

Instruction #1065328 B

Owner’s Manual and Assembly Instructions

For Residential Use Only

MODEL # 151110

(For Family Domestic Use Only. This product is intended for outdoor use.)

**U.S. and Canada customers ONLY**

IF ASSISTANCE IS NEEDED,

DO NOT CONTACT THE STORE!

CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865

HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)

Call or visit our Web site at www.lifetime.com for Saturday hours

**For customers outside the U.S. or Canada, please contact the store for assistance.**

This product is intended for use by children ages 3 to 12

and is for residential use only.

Lifetime Products, Inc.

10#PYt'SFFQPSU$FOUFS#MEH%

$MFBSGJFME6UBI

COPY

Save this owner’s manual for future reference and in

the event that the manufacturer has to be contacted.

WARNING

Most injuries are caused by misuse and/or not following instructions. Use caution when using this play equipment.

To ensure safety, do not attempt to assemble this play equipment without carefully following

the instructions. Before beginning assembly, read the instructions. Proper and complete

assembly, orientation, and supervision are essential to reduce the risk of accident or injury.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS

INJURY OR PROPERTY DAMAGE AND WILL VOID THE WARRANTY.

Before Beginning Assembly!

Three Adults Required for Assembly

Indicates the number of

people required to complete

assembly step.

Only adults should set up the play equipment. Do not allow children in the

setup area until assembly is complete.

This product is intended for use by children

ages 3 to 12 and is for domestic use only.

1/2 in. wrench, or adjustable wrench

2x 3/4 in. wrench, or adjustable wrench

Tools Required for Assembly

Phillips Screwdriver

2x 3/16 in. Allen wrench (included)

Customer Service:

1-800-225-3865

Monday-Friday 7 a.m. to 5 p.m. MST

Call or visit our Web site at www.lifetime.com for Saturday hours

Lifetime Products, Inc.

P.O. Box 160010

&OHDU¿HOG87

COPY

**IMPORTANT SAFETY INFORMATION**

PLEASE READ BEFORE BEGINNING

ASSEMBLY:

Installation and Ground Preparation Instructions:

 3ODFHWKHHTXLSPHQWRQZHOOGUDLQHGOHYHOVXUIDFHDWOHDVWPIWIURPDQ\VWUXFWXUHRU

REVWUXFWLRQVXFKDVDIHQFHJDUDJHRUKRXVH

 3URYLGHHQRXJKURRPVRWKDWFKLOGUHQFDQXVHWKHHTXLSPHQWVDIHW\)RUH[DPSOHIRUVWUXFWXUHV

ZLWKPXOWLSOHSOD\DFWLYLWLHVDVOLGHVKRXOGQRWH[LWLQIURQWRIDVZLQJ

 6HSDUDWHDFWLYHDQGTXLHWDFWLYLWLHVIURPHDFKRWKHU)RUH[DPSOHORFDWHVDQGER[HVDZD\IURP

VZLQJVRUXVHDJXDUGUDLORUEDUULHUWRVHSDUDWHWKHVDQGER[IURPWKHPRYHPHQWRIWKHVZLQJV

 'RQRWLQVWDOOKRPHHTXLSPHQWRYHUFRQFUHWHDVSKDOWSDFNHGHDUWKRUDQ\RWKHUKDUGVXUIDFH$

IDOORQWRDKDUGVXUIDFHFDQUHVXOWLQVHULRXVLQMXU\WRWKHHTXLSPHQWXVHUVHHSDJH

 7RSUHYHQWVHULRXVLQMXU\ZDUQFKLOGUHQWKDWWKH\PXVWQRWXVHWKHHTXLSPHQWXQWLOSURSHUO\

LQVWDOOHG

 &UHDWHDVLWHIUHHRIREVWDFOHVWKDWFRXOGFDXVHLQMXULHV±VXFKDVORZRYHUKDQJLQJWUHHEUDQFKHV

RYHUKHDGZLUHVWUHHVWXPSVDQGRUURRWVODUJHURFNVEULFNVDQGFRQFUHWH

 &KRRVHDOHYHOORFDWLRQIRUWKHHTXLSPHQW7KLVFDQUHGXFHWKHOLNHOLKRRGRIWKHSOD\VHWWLSSLQJ

RYHUDQGORRVH¿OOVXUIDFLQJPDWHULDOVZDVKLQJDZD\GXULQJKHDY\UDLQV

 )RUDQ\TXHVWLRQVFDOORXU&XVWRPHU6HUYLFH'HSDUWPHQWDWIRUPRUHLQIRUPD

WLRQ

Playground and Surface Materials Instructions:

 8VHFRQWDLQPHQWVXFKDVGLJJLQJRXWDURXQGWKHSHULPHWHUDQGRUOLQLQJWKHSHULPHWHUZLWKODQG

VFDSHHGJLQJ

 'RQRWLQVWDOOORRVH¿OOVXUIDFLQJRYHUKDUGVXUIDFHVVXFKDVFRQFUHWHRUDVSKDOW

 ,QVWDOODWLRQVRIUXEEHUWLOHVRUSRXUHGLQSODFHVXUIDFHVRWKHUWKDQORRVH¿OOPDWHULDOVJHQHUDOO\

UHTXLUHDSURIHVVLRQDODQGDUHQRW³GRLW\RXUVHOI´SURMHFWV

 8VH3OD\JURXQG6XUIDFLQJ0DWHULDOVRWKHUWKDQORRVH¿OOPDWHULDOZKLFKFRPSO\WRWKHVDIHW\

VWDQGDUG$670)6WDQGDUG6SHFL¿FDWLRQIRU,PSDFW$WWHQXDWLRQRI6XUIDFLQJ0DWHULDOV

ZLWKLQWKH8VH=RQHRI3OD\JURXQG(TXLSPHQW

Maintenance Instructions:

 ,IURXWLQHFKHFNVDQGPDLQWHQDQFHSURFHGXUHVDUHQRWGRQHWKHHTXLSPHQWFRXOGRYHUWXUQDQGRUEH

FRPHDKD]DUG

 &KHFNVXUIDFLQJPDWHULDODQGUHSOHQLVKDVQHFHVVDU\WRPDLQWDLQSURSHUGHSWKVHHSDJH

 5DNHVXUIDFLQJSHULRGLFDOO\WRSUHYHQWFRPSDFWLRQDQGPDLQWDLQDSSURSULDWHGHSWKV

 5HPRYHDQ\WULSSLQJKD]DUGVVXFKDVH[SRVHGFRQFUHWHIRRWLQJVWUHHVWXPSVRUURFNV

 &KHFNDOOQXWVDQGEROWVWZLFHPRQWKO\GXULQJWKHXVDJHVHDVRQIRUWLJKWQHVVDQGWLJKWHQDVUH

TXLUHG,WLVSDUWLFXODUO\LPSRUWDQWWKDWWKLVSURFHGXUHEHIROORZHGDWWKHEHJLQQLQJRIHDFKVHDVRQ

 &KHFNDOOFRYHULQJVIRUEROWVDQGVKDUSHGJHVWZLFHPRQWKO\GXULQJXVDJHVHDVRQWREHFHUWDLQ

WKH\DUHLQSODFH5HSODFHZKHQQHFHVVDU\,WLVHVSHFLDOO\LPSRUWDQWWRGRWKLVDWWKHEHJLQQLQJRI

HDFKQHZVHDVRQ

 2LODOOPHWDOOLFPRYLQJSDUWVPRQWKO\GXULQJWKHXVDJHSHULRG

 'RQRWXVHZKHQWKHWHPSHUDWXUHGURSVEHORZ

)

&

 6DQGUXVWHGDUHDVRQWXEXODUPHPEHUVDQGUHSDLQWXVLQJDQRQOHDGEDVHGSDLQWPHHWLQJWKHUHTXLUH

PHQWVRI7LWOH&)53DUW

 ,IWKHZDUQLQJVWLFNHULVLOOHJLEOHGHVWUR\HGRUUHPRYHGFRQWDFWWKH&XVWRPHU6HUYLFH'HSDUWPHQW

DWIRUDUHSODFHPHQW&RQWDFW&XVWRPHU6HUYLFHWRUHSODFHDQ\GHIHFWLYHSDUWV

Disposal Instructions: 'LVDVVHPEOHDQGGLVSRVHRIWKHSOD\JURXQGHTXLSPHQWLQVXFKDZD\WKDW

QRXQUHDVRQDEOHKD]DUGVZLOOH[LVWDWWKHWLPHWKHVZLQJVHWLVGLVFDUGHG)ROORZDOOORFDOGLVSRVDO

UHTXLUHPHQWV

Operating Instructions:

 2EVHUYLQJWKHIROORZLQJLQVWUXFWLRQVDQGZDUQLQJVUHGXFHVWKHOLNHOLKRRGRIVHULRXVRUIDWDO

LQMXU\

 7KHPD[LPXPQXPEHURIRFFXSDQWVWKDWPD\VDIHO\XVHWKHHQWLUHSOD\VHWLQFOXGLQJDOOFRPSR

QHQWVLVZLWKDPD[LPXPZHLJKWRISRXQGV

 2QVLWHDGXOWVXSHUYLVLRQVKRXOGEHSURYLGHGIRUFKLOGUHQRIDOODJHV

 ,QVWUXFWFKLOGUHQQRWWRZDONFORVHWRLQIURQWRIEHKLQGRUEHWZHHQPRYLQJLWHPV

 ,QVWUXFWFKLOGUHQWRVLWRQO\RQWKHVHDWV

 ,QVWUXFWFKLOGUHQQRWWRXVHWKHHTXLSPHQWLQDPDQQHURWKHUWKDQLQWHQGHG

 ,QVWUXFWFKLOGUHQQRWWRJHWRIIHTXLSPHQWZKLOHLWLVLQPRWLRQ

 7RSUHYHQWHQWDQJOHPHQWDQGVWUDQJXODWLRQGUHVVFKLOGUHQDSSURSULDWHO\XVLQJZHOO¿WWLQJVKRHV

DQGDYRLGLQJSRQFKRVVFDUYHVMDFNHWVZLWKQHFNGUDZVWULQJVKHOPHWVZLWKVWUDSVDQGRWKHU

ORRVH¿WWLQJFORWKLQJWKDWLVSRWHQWLDOO\KD]DUGRXVZKLOHXVLQJHTXLSPHQW

 ,QVWUXFWFKLOGUHQQRWWRSOD\ZKHQWKHHTXLSPHQWLVZHW

 ,QVWUXFWFKLOGUHQQRWWRDWWDFKLWHPVWRWKHSOD\JURXQGHTXLSPHQWWKDWDUHQRWVSHFL¿FDOO\GH

VLJQHGIRUXVHZLWKWKHHTXLSPHQWVXFKDVEXWQRWOLPLWHGWRMXPSURSHVFORWKHVOLQHSHWOHDVK

HVFDEOHVDQGFKDLQDVWKH\PD\FDXVHDVWUDQJXODWLRQKD]DUG

 'RQRWPRYHZKLOHLQXVH

7KH86&RQVXPHU3URGXFW6DIHW\&RPPLVVLRQ

&36&HVWLPDWHVWKDWDERXWSOD\JURXQG

HTXLSPHQWUHODWHGLQMXULHVUHVXOWLQJIURPIDOOVWRWKH

JURXQGVXUIDFHDUHWUHDWHGDQQXDOO\LQ86KRVSLWDO

HPHUJHQF\URRPV,QMXULHVLQYROYLQJWKLVKD]DUGSDWWHUQ

WHQGWREHDPRQJWKHPRVWVHULRXVRIDOOSOD\JURXQG

LQMXULHVDQGKDYHWKHSRWHQWLDOWREHIDWDOSDUWLFXODUO\

ZKHQWKHLQMXU\LVWRWKHKHDG7KHVXUIDFHXQGHUDQG

DURXQGSOD\JURXQGHTXLSPHQWFDQEHDPDMRUIDFWRULQ

GHWHUPLQLQJWKHLQMXU\FDXVLQJSRWHQWLDORIDIDOO,WLV

VHOIHYLGHQWWKDWDIDOORQWRDVKRFNDEVRUELQJVXUIDFH

LVOHVVOLNHO\WRFDXVHDVHULRXVLQMXU\WKDQDIDOORQWR

DKDUGVXUIDFH3OD\JURXQGHTXLSPHQWVKRXOGQHYHU

EHSODFHGRQKDUGVXUIDFHVVXFKDVFRQFUHWHRUDVSKDOW

DQGZKLOHJUDVVPD\DSSHDUWREHDFFHSWDEOHLWPD\

TXLFNO\WXUQWRKDUGSDFNHGHDUWKLQDUHDVRIKLJKWUDI

¿F6KUHGGHGEDUNPXOFKZRRGFKLSV¿QHVDQGRU¿QH

JUDYHODUHFRQVLGHUHGWREHDFFHSWDEOHVKRFNDEVRUELQJ

VXUIDFHVZKHQLQVWDOOHGDQGPDLQWDLQHGDWDVXI¿FLHQW

GHSWKXQGHUDQGDURXQGSOD\JURXQGHTXLSPHQW

7DEOHOLVWVWKHPD[LPXPKHLJKWIURPZKLFKDFKLOG

ZRXOGQRWEHH[SHFWHGWRVXVWDLQDOLIHWKUHDWHQLQJKHDG

LQMXU\LQDIDOORQWRGLIIHUHQWORRVH¿OOVXUIDFLQJPDWHUL

DOVLIWKH\DUHLQVWDOOHGDQGPDLQWDLQHGDWGHSWKVRI

DQGLQFKHV+RZHYHULWVKRXOGEHUHFRJQL]HGWKDW

DOOLQMXULHVGXHWRIDOOVFDQQRWEHSUHYHQWHGQRPDWWHU

ZKDWVXUIDFLQJPDWHULDOLVXVHG

,WLVUHFRPPHQGHGWKDWDVKRFNDEVRUELQJPDWHULDO

VKRXOGH[WHQGDPLQLPXPRIIWLQDOOGLUHFWLRQVIURP

WKHSHULPHWHURIVWDWLRQDU\HTXLSPHQWVXFKDVFOLPEHUV

DQGVOLGHV+RZHYHUEHFDXVHFKLOGUHQPD\GHOLEHU

DWHO\MXPSIURPDPRYLQJVZLQJWKHVKRFNDEVRUELQJ

PDWHULDOVKRXOGH[WHQGLQWKHIURQWDQGUHDURIDVZLQJ

DPLQLPXPGLVWDQFHRIWLPHVWKHKHLJKWRIWKHSLYRW

SRLQWPHDVXUHGIURPDSRLQWGLUHFWO\EHQHDWKWKHSLYRW

RQWKHVXSSRUWLQJVWUXFWXUH

7KLVLQIRUPDWLRQLVLQWHQGHGWRDVVLVWLQFRPSDULQJWKH

UHODWLYHVKRFNDEVRUELQJSURSHUWLHVRIYDULRXVPD

WHULDOV1RSDUWLFXODUPDWHULDOLVUHFRPPHQGHGRYHU

DQRWKHU+RZHYHUHDFKPDWHULDOLVRQO\HIIHFWLYHZKHQ

SURSHUO\PDLQWDLQHG0DWHULDOVVKRXOGEHFKHFNHGSH

ULRGLFDOO\DQGUHSOHQLVKHGWRPDLQWDLQFRUUHFWGHSWKDV

GHWHUPLQHGQHFHVVDU\IRU\RXUHTXLSPHQW7KHFKRLFH

RIDPDWHULDOGHSHQGVRQWKHW\SHDQGKHLJKWRIWKH

SOD\JURXQGHTXLSPHQWWKHDYDLODELOLW\RIWKHPDWHULDO

LQ\RXUDUHDDQGLWVFRVW

7KLVLQIRUPDWLRQKDVEHHQH[WUDFWHGIURPWKH&36&SXEOLFDWLRQV³3OD\JURXQG6XUIDFLQJ7HFKQLFDO,QIRUPDWLRQ*XLGH´DQG³+DQGERRNIRU3XEOLF3OD\

JURXQG6DIHW\´&RSLHVRIWKHVHUHSRUWVFDQEHREWDLQHGE\VHQGLQJDSRVWFDUGWRWKH2I¿FHRI3XEOLF$IIDLUV86&RQVXPHU3URGXFW6DIHW\&RPPLVVLRQ

:DVKLQJWRQ'&RUFDOOWKHWROOIUHHKRWOLQH

7KLVGDWDLVIURPWHVWVFRQGXFWHGE\LQGHSHQGHQWWHVWLQJODERUDWRULHVRQDLQFKGHSWKRIXQFRPSUHVVHGVKUHGGHGWLUHVDPSOHVSURGXFHGE\IRXU

PDQXIDFWXUHUV,WLVUHFRPPHQGHGWKDWSHUVRQVVHHNLQJWRLQVWDOOVKUHGGHGWLUHVDVDSURWHFWLYHVXUIDFHUHTXHVWWHVWGDWDIURPWKHVXSSOLHUVKRZLQJWKHFULWLFDO

KHLJKWRIWKHPDWHULDOZKHQLWZDVWHVWHGLQDFFRUGDQFHZLWK$670)

CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS*

**The maximum fall height for this product is 36 in. We recommend

using 6 in. of Double Shredded Bark Mulch.**

TABLE 1 — FALL HEIGHT IN FEET FROM WHICH A LIFE THREATENING HEAD

INJURY WOULD NOT BE EXPECTED

Type of Material

'RXEOH6KUHGGHG%DUN0XOFK

:RRG&KLSV

)LQH6DQG

)LQH*UDYHO

6KUHGGHG7LUHV

















1$









1$

6 in. depth 9 in. depth 12 in. depth

A cordless drill can be used for driving screws;

however, care should be taken not to over-tighten or strip screws.

USE AT YOUR OWN RISK!

Safety Zone for the Airplane

6.5 ft (2m)

USING A DRILL IS NOT RECOMMENDED

FOR DRIVING BOLTS.

H (Blue)

I (Blue)

L (Blue)

M (Blue)

N (Yellow)

O (Yellow)

Q (Blue)

A i r p l a n e P a r t s L i s t

ID Part # Item Description Qty

A 8002634 Front Cross Brace 1

B 8002635 Back Cross Brace 1

C 8002626 Middle Cross Brace 1

D 1064707 Support Brace 1

E 8002685 Front Skid 2

F 8002686 Back Skid 2

G 8002345 Adjustment Stand 2

H 8002333 Front Fuselage 2

I 8002334 Back Fuselage 2

J 8002628 Top Fuselage 2

K 8002629 Bottom Fuselage 2

L 1064945 Front Seat Backrest 1

M 1064947 Back Seat Backrest 1

N 8002504 Plastic Cockpit Backrest 2

ID Part # Item Description Qty

O 8002633 Cockpit Seat 2

P 1064983 Cockpit Seat Support 2

Q 1064984 Front Horizontal Pivot 1

R 1065148 Wing Support Brace 2

S 8002687 Wing Pieces 4

T 8002335 Wing Handle 2

U 1065265 Wing Tip with Seat 2

V 1063087 Rudder Tail with Seats 1

W 1065159 Nose with Dash 1

X 8002341 Steering Tube 1

Y 1065225 Steering Wheel 1

Z 8002514 Propeller 1

AA 1045818 Chain Foot Rest 1

A (Red)

B (Red)

C (Red)

E (Red)

F (Red)

D (Red)

G (Red)

J (Blue)

K (Blue)

P (Blue)

Remove from inside E or F

X (Red)

A i r p l a n e H a r d w a r e L i s t

ID Part # Item Description Qty

HA 8000307 5/16 in. x 2 Bolt 16

HB 8002809 1/4 in. x 1 1/2 in. Bolt 14

HC 8002810 1/4 in. x 1 1/8 in. Bolt 24

HE 8002726 Phillips Screw 16

HF 8002727 2 in. Phillips Screw 4

HG 8002811 T-Nut 38

HH 8002027 Washer 67

HJ 8002703 Brass Bushing 2

HK 8002490 1/2 in. x 2 1/4 in. Hex Bolt 2

HL 8002491 1/2 in. Center Lock Nut 2

ID Part # Item Description Qty

HM 8002492 1/2 in. Washer 4

HN 8005260 5/16 in. Formed Washer 2

HO 8000534 5/16 in. x 2 1/2 in. Bolt 1

HP 8000209 5/16 in. Nylock Nut 3

HQ 8000162 5/16 in. x 3/4 in. Bolt 1

HR 8000163 5/16 in. x 1 1/4 in. Bolt 2

HS 8002824 5/16 in. x 2 in. Pivot Bolt 2

HT 8000355 Allen Wrench 2

1065271 Hardware Bag - Caps

HU 1064772 Coped Cap 14

There may be extra hardware

R (Red)

S (Red)

T (Red)

V (Yellow, Red)

W (Yellow, Red)

Y (Red)

Z (Red)

U (Yellow, Red)

HO HP

Connect the two Front Skids (E) to

the Cross Brace (A) with the hardware

shown.

Connect the two Back Skids (F) to the Back Cross

Brace (B) and the Middle Cross Brace (C). Secure

with the hardware shown

HG x 4

T-Nut

Washer

HH x 4

HG x 8

T-Nut

Washer

HH x 8

Do not fully tighten until after step 4

Thi

acin

down.

Thi

hould be

acin

the

Do not fully tighten until after step 4

Thi

in th

oca

wn.

HB x 4

1 1/2 in. Bolt

HB x 8

Connect the two assemblies completed in steps

1 - 3. Secure with the hardware shown.

HG x 2

T-Nut

Washer

HH x 2

Secure all the hardware

from steps 1-4

Place the Support Brace (D) in the location shown.

Secure with the hardware shown.

7KHLQ%ROW+2PXVWEHSODFHG¿UVWDVVKRZQLQ

the images.

Nylock-Nut

Washer

HH x 3

HH HH

Do Not Overtighten Hardware

HO x 1

2 1/2 in. Bolt

HP x 1

Do not fully tighten until after step 4

HB x 2

1 1/2 in. Bolt

3/4 in. Bolt

HQ x 1

Place the Adjustment Stand (G) into

the Cross Braces (A & B). Secure with

the hardware shown.

To begin, place the adjustment stands

at the middle hole and make sure both

are at the same height setting.

HK x 2

2 1/4 in. Hex Bolt

HL x 2

1/2 in. Nut

HM x 4

1/2 in. Washer

Connect a Plastic Cockpit Backrest (N) to the Back Seat Backrest (M).

Secure using the hardware shown. Do not over tighten.

There are warning stickers on the back of each seat, make sure the

seats are placed so the stickers are right side up.

Place the hardware in

the order shown

Hole 1 for younger children

Hole 3 for older children

HE x 4

Phillips Screw

Connect a Plastic Cockpit Backrest (N) to the Front Seat Backrest (L).

Secure using the hardware shown. Do not over tighten.

There are warning stickers on the back of each seat, make sure the seats

are placed so the stickers are right side up.

Begin the fuselage assembly by connecting the Front Fuselage (H) to

the Top Fuselage (J) and the Bottom Fuselage (K). Slide this assembly

into the back Fuselage (I).

Do not fully tighten Fuselage

or Wing hardware until after step 19.

Place the hardware in

the order shown

The Bottom Fusela

(

)

has more holes than the

Top Fusela

(

)

, and must be placed on the bottom

HE x 4

Phillips Screw

Repeat steps 8 and 9 (with the T-Nut (HG) going the opposite direction) to

complete the other fuselage frame.

Stand the two assemblies up next to each other (with the T-Nuts on the inside of

WKHIXVHODJHDQGWKHGLPSOHVRQWKHRXWVLGHRIWKHIXVHODJHLQRUGHUWR¿QLVKWKH

rest of the fuselage assembly.

HG x 4

T-Nut

Washer

HH x 4

Secure Fuselage Frame with the hardware shown. Do not

completely tighten hardware.

Do not put the hardware

in th

ese

t thi

tim

Dimples on tubes must

ace the

opposite direction o

the T-Nuts.

HC x 4

1 1/8 in. Bolt

Place the assembled Back Seat Backrest

(M) in between the two fuselage frames.

Place the Coped Caps (HU) in the location

pictured and line up

the holes in the Back

Seat Backrest (M),

with the holes in the

fuselage frame.

Attach the assembled Front Seat Backrest (L) in

between the two fuselage frames. Place the Coped

Caps (HU) on the tubes indicated. Line up the holes

in the Front Seat Backrest (L), with the holes in the

fuselage frame.

Attach the backrest to the fuselage frame using the

hardware shown below.

Washer

HH x 8

Do not completely tighten hardware.

Two Adults

Required for

Assembly

Do not completely

tighten hardware.

HA x 8

2 in. Bolt

Attach the backrest to the fuselage frame using

the hardware shown.

HH x 2

Position the Seat Support (P) in the location

shown, with a Coped Cap (HU) on each end.

Place the hardware through the fuselage

IUDPHVDQGLQWRWKHVHDWVXSSRUWDQG¿QJHU

tighten. This hardware is temporary and will

be removed later.

Tip the fuselage on its side to position the

Cockpit Seat. Secure with the hardware in the

order shown.

Place the Cockpit Seat (O) in the position

shown.

HA x 2

2 in. Bolt

Washer

bead

should be facing down.

HE x 4

Phillips Screw

Position the Front Pivot (Q) in the location

at the front of the fuselage assembly with a

Coped Cap (HU) at each end as shown.

Secure with the hardware shown.

Washer

HH x 2

HA x 2

2 in. Bolt

Do not completely tighten hardware.

Position the Seat Support (P) in the location

shown, with Coped Caps (HU) on each end

of the tube. Place the hardware through the

fuselage frames and into the seat support

DQG¿QJHUWLJKWHQDVVKRZQ7KLVKDUGZDUHLV

temporary and will be removed later.

Tip the fuselage on its side to position the

Cockpit Seat. Secure with the hardware in the

order shown.

HH x 2

Place the Cockpit Seat (O) in the position

shown.

HA x 2

2 in. Bolt

Washer

bead

should be facing down.

HE x 4

Phillips Screw

Washer

HS x 2

2 in. Pivot Bolt

HJ x 2

Brass Bushing

Three Adults

Required for Assembly

HP x 2

HH x 4

5/16 in. Nylock Nut

Using two people lift the fuselage assembly and position it on the skid and cross brace assembly. Line

up the holes, in the Front Pivot (Q) and the Backseat Backrest (M), with the holes in the Adjustment

stands (G).

+DYHDWKLUGSHUVRQSODFHWKH%UDVV%XVKLQJ+-LQSRVLWLRQ¿UVW6HFXUHZLWKWKHKDUGZDUHVKRZQ

Make sure the bolts have gone through the Brass Bushing, and the hardware is assembled as shown.

Place the Wing Handle (T) onto the Wing End

with Seat (U) in the position shown. Line up the

holes and secure with the hardware are shown.

The hardware also secures the Wing Pieces (S)

to the Wing End with Seat

HHHH

Repeat this step for the other Wing Assembly.

Slide the Wing Pieces (S) into the Wing Tip

Seat (U) as shown.

HG x 8

T-Nut

Washer

HH x 8

Make sure the Brackets on the bottom of the Wing

Pieces (S) are placed in the proper position. See

Image.

Incorrect

Correct

Do not completely tighten

hardware.

HC x 8

1 1/8 in. Bolt

Place the Foot Rest (AA) in the location shown. Secure the

Foot Rest (AA) to the fuselage with the hardware shown by

positioning the chain links over the holes in the fuselage and

placing a Bolt (HC) and Washer (HH) through the chain links

and into the hole.

HG x 2

T-Nut

Washer

HH x 2

HC HC

HC x 2

1 1/8 in. Bolt

Slide the Wing Support Brace (R) into the bottom tube of

the Front Seat Backrest (L) as shown. Secure with the

hardware shown.

Do not completely tighten hardware.

HG x 1

T-Nut

Washer

HH x 1

HC x 1

1 1/8 in. Bolt

Secure the wing assembly to the

fuselage by replacing the 2 in. Bolts

(HA), Washers (HH), and adding the

rest of the hardware as shown.

Make sure the 2 in. Bolts (HA) go into

the seat support.

Position the Wing Assembly into the notch at the end

of the Wing Support Brace (R), and over the holes in

the fuselage as shown. Secure the Wing to the Wing

Support Brace with the hardware shown.

Remove the 2 in. Bolts (HA) and

Washers (HH) from the seat support

(on the side of the Fuselage shown)

that were placed in steps 11 and 12.

HG x 2

T-Nut

Washer

HH x 3

Do not completely tighten

hardware.

Two Adults

Required for

Assembly

HA x 1

2 in. Bolt

HC x 2

1 1/8 in. Bolt

Slide the other Wing Support Brace (R)

into the bottom tube of the Front Seat

Backrest (L) as shown. Secure with the

hardware shown.

HG x 1

T-Nut

Washer

HH x 1

Do not completely tighten

hardware.

HC x 1

1 1/8 in. Bolt

HG x 2

T-Nut

Washer

HH x 3

2 in. Bolt

Position the Wing Assembly into the notch at the end

of the Wing Support Brace (R), and over the holes in

the fuselage as shown. Secure the Wing to the Wing

Support Brace with the hardware shown.

Secure the wing assembly to the

fuselage by replacing the 2 in. Bolts

(HA), Washers (HH), and adding the

rest of the hardware as shown.

Make sure the 2 in. Bolts (HA) go into

the seat support.

Remove the 2

in. Bolts (HA) and

Washers (HH) from the seat support

(on the side of the Fuselage shown)

that were placed in steps 11 and 12.

Do not completely

tighten hardware.

Two Adults

Required for

Assembly

HA x 1

HC x 2

1 1/8 in. Bolt

Page is loading ...

Lifetime 151110 Owner's manual

Related papers

Other documents