ADDER AdderLink Infinity 4021 Quick start guide

ADDER
Brand
ADDER
Model
AdderLink Infinity 4021
Category
Network media converters
Type
Quick start guide

This manual is also suitable for

The ADDER AdderLink Infinity 4021 is a high-performance KVM extender that allows you to extend your computer's keyboard, video, and mouse signals up to 100 meters over a single fiber optic cable. It supports resolutions up to 4K UHD (3840x2160) at 60Hz with 24-bit color depth, and it features a transparent USB 2.0 port for connecting peripherals such as printers or scanners. The 4021 also has a built-in audio transmitter and receiver, allowing you to extend audio signals along with your video and data.

The ADDER AdderLink Infinity 4021 is a high-performance KVM extender that allows you to extend your computer's keyboard, video, and mouse signals up to 100 meters over a single fiber optic cable. It supports resolutions up to 4K UHD (3840x2160) at 60Hz with 24-bit color depth, and it features a transparent USB 2.0 port for connecting peripherals such as printers or scanners. The 4021 also has a built-in audio transmitter and receiver, allowing you to extend audio signals along with your video and data.

ALIF4000 RX
10 Gigabit
Switching
ALIF4000 RX
ALIF4000 RX
ALIF4000 TX
ALIF4000 RX
ALIF4000 TX
Welcome
This quick start guide covers some of the key points of the ADDERLink™ INFINITY 4000 unit. Full user details
and setup instructions can be found at www.adder.com/en/kvm-solutions/adderlink-innity-4000
Please read the supplied safety instruction leaet before use.
Initial conguration
ALIF4000 units can be linked in two mains ways: Direct or Networked.
Direct linking
Where ALIF4000 transmitters and receivers are directly linked to each other, very little conguration
action is required, provided that they both have their factory default settings in place - just link them
together. If the standard settings have been changed in a previous installation, you merely need to
perform a manual factory reset on each unit. Please see the center pages.
ADDERLink
™
INFINITY 4000
Quick Start
© 2019 Adder Technology Limited • All trademarks are acknowledged.
Part No. MAN-QS-ALIF4000-ADDER_V2.0
www.adder.com
Networked linking
Where ALIF4000 units are connected via networked links, you can either congure them individually,
or congure them collectively using an AIM server:
• Conguring networked ALIF units individually - You need to specify the network addresses
of the ALIF4000 units so that they can locate each other. This can be done using via OSD on the
console connected to the RX unit by pressing CTRL + A LT + C. Please see the rear page.
• Conguring networked ALIF units collectively - The ADDERLink™ INFINITY Management
(AIM) server allows you to congure, control and coordinate any number of ALIF transmitters and
receivers from a single application. See adder.com for details.
IMPORTANT: When using AIM to congure ALIF units, it is
vital that all units that you wish to locate and control are
set to their factory default settings. Otherwise they will
not be located by the AIM server. If necessary, perform a
manual factory reset on each ALIF unit. See center pages.
Note: If you are using one or more ALIF4000 transmitters
within an installation managed by an AIM server, the AIM
server must be running rmware version 4.9 or above.
ADDERLink™ INFINITY 4000 conguration via web pages
Each ALIF4000 unit hosts its own internal set of web pages which contain all conguration details
and settings. You will need to use a computer connected to the same network as each ALIF4000
unit to access the web pages. Additionally, on the console attached to the ALIF4000 RX unit, you
can access its conguration details via the On Screen Display (OSD) by pressing CTRL + ALT + C.
To configure ALIF4000 units via their web pages
Run a web browser on your computer and enter the IP address of the required ALIF4000 unit:
The default addresses are TX: 169.254.1.33 and RX: 169.254.1.32
If the IP address of a unit has been changed, you can either:
• Discover the unit’s main IP address by pressing the small
button on the front panel next to the OLED screen to reveal
the value for IP Address 3.
• Alternatively, providing it is appropriate to do so, perform a manual factory reset (see the
center pages) to restore the default address.
The opening page should be displayed:
Full user details and setup instructions can be found at:
www.adder.com/en/kvm-solutions/adderlink-innity-4000
IP Address 3
169.254.1.33
Connections
To perform a manual factory reset
A factory reset returns ALIF4000 unit to its default conguration.
1 Power on the ALIF4000 unit.
2 Use a long narrow implement (e.g. a straightened-out paper clip) to press-and-hold the recessed reset button on the front panel
for roughly ten seconds, until the status indicator turns blue (Note: alternating red/green indications will occur during the ten second
period while the button is still pressed).
3 Release the reset switch. The indicator will remain blue for a short while (less than ten seconds) while ALIF4000 unit congures
itself and should then change to green if all connections are correct; or orange if one or more of the video, USB and/or network
links are missing.
Note: If you are performing a factory reset and intend to disconnect the power immediately after the reset, you must wait at least 30
seconds after you have released the reset button for it to complete the process.
AdderLink
4000
RECEIVE
2
3
1
1
1
2
2
4
5
34
optical
OUT
12V
3A
AdderLink
4000
TRANSMIT
2
3
1
4
12
4
12
optical
OUT
AUX
IN
12V
3A
Power
in
Power
in
USB
port
USB
Reserved Reserved
Reserved
TX unit RX unit
Reserved
Primary
video in
Primary
display
Primary fiber link (using 10GbE SFP modules) - direct link or via suitable switch
Secondary fiber link (using 10GbE SFP modules) - direct link or via suitable switch
Primary
SFP port
Primary
SFP port
Reset
switch
Reset
switch
Headphones USB
port
Audio
in
Audio
out
Secondary
video in
Secondary
display
Secondary
SFP port
Secondary
SFP port
Microphone
USB2.0
transparent
high speed
port
Audio
out
AdderLink
  • Page 1 1
  • Page 2 2

ADDER AdderLink Infinity 4021 Quick start guide

ADDER
Brand
ADDER
Model
AdderLink Infinity 4021
Category
Network media converters
Type
Quick start guide
This manual is also suitable for

The ADDER AdderLink Infinity 4021 is a high-performance KVM extender that allows you to extend your computer's keyboard, video, and mouse signals up to 100 meters over a single fiber optic cable. It supports resolutions up to 4K UHD (3840x2160) at 60Hz with 24-bit color depth, and it features a transparent USB 2.0 port for connecting peripherals such as printers or scanners. The 4021 also has a built-in audio transmitter and receiver, allowing you to extend audio signals along with your video and data.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents