Cisco Systems OL-7822-06 User manual

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco Service Control Engine 1000 2xGBE

Quick Start Guide

Release 3.1

May 2007

Customer Order Number:

Text Part Number: OL-7822-06

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick

Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified

Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation,

Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ

Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing,

ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO

are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0501R)

iii

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

CONTENTS

CHAPTER

1 Prepare for Installation 1-1

Information About Preparing for Installation 1-1

Site Preparation and Unpacking 1-1

Tools and Parts 1-2

Prepare for Rack-Mount Installation 1-2

Workbench or Tabletop Installation 1-2

CHAPTER

2 Rack-Mount the SCE 1000 2-1

The SCE 1000 Mounting Brackets 2-1

Attach the Brackets to the SCE 1000 2-2

Installing the Crossrail Supports (Four-post rack only) 2-3

Assemble the Crossrail Supports 2-3

Attach the Crossrail Supports to the Rack 2-4

Mount the System to the Rack 2-4

CHAPTER

3 Connect the Power Supply Units 3-1

Connect the Chassis Ground 3-1

Connecting the Power 3-2

Connect the DC-Input Power Supply Unit 3-3

Connect the AC-Input Power Supply Unit 3-4

CHAPTER

4 Connect the Management Interfaces and Perform Initial System Configuration 4-1

Connect the Local Console 4-1

Perform the Initial System Configuration 4-2

Initial System Configuration 4-2

The Setup Command 4-3

Setup Command Parameters 4-4

Example 4-6

Step 1: Configuring Initial Settings 4-6

Example 4-7

Step 2: Configuring the Hostname 4-7

Step 3: Setting the Passwords 4-7

Contents

iv

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

EXAMPLE: 4-8

Step 4: Configuring Time Settings 4-8

EXAMPLE: 4-10

Step 5: Configuring the DNS Settings 4-10

EXAMPLE: 4-11

Step 6: Configuring the RDR Formatter Destination 4-12

EXAMPLE: 4-12

Step 7: Configuring Access Control Lists (ACLs) 4-12

Information About Access Control Lists 4-12

Examples 4-15

Step 8: Configuring SNMP 4-16

EXAMPLE: 4-19

Step 9: Configuring the Topology-Dependent Parameters 4-20

About the Topology-Dependent Parameters 4-20

Examples 4-21

Step 10: Completing and Saving the Configuration 4-22

Examples 4-24

Connect the Management Interface 4-25

EXAMPLE: 4-25

CHAPTER

5 Cable the Line Ports 5-1

Information About Cabling 5-1

Single Link: Inline Topology 5-1

Single Link: Receive-only Topology 5-2

Cabling the Line Interfaces 5-3

Configure GigabitEthernet Auto-Negotiation 5-3

Connect the GBE Line Interface Ports 5-4

CHAPTER

6 Completing the Installation 6-1

Examining the LEDs 6-1

Final Tests 6-1

Verifying Operational Status 6-1

Example: 6-2

Viewing the User Log Counters 6-2

EXAMPLE: 6-2

Viewing Configuration 6-2

Saving the Configuration Settings 6-3

Examples 6-4

EXAMPLE 1: 6-4

Contents

v

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

EXAMPLE 2: 6-4

CHAPTER

7 Installing a Service Control Application 7-1

Advanced Configuration of the SCE Platform 7-1

Loading and Activating a Service Control Application 7-1

CHAPTER

8 Troubleshoot Startup Problems 9-1

SCE 1000 Operational Status 9-1

Identifying Startup Problems 9-3

CLI Commands for Troubleshooting 9-3

Contents

vi

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

CHAPTER

1-1

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

1

Prepare for Installation

This section contains warnings, information about tools and parts, site preparation information, and

information for workbench or tabletop installation and rack-mount installation.

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with

standard practices for preventing accidents. To see translations of the warnings that appear in this

publication, refer to the translated safety warnings that accompanied this device.

Only trained and qualified personnel should install, replace, or service this equipment.

Read the installation instructions before you connect the system to its power source.

This unit is intended for installation in restricted access areas. A restricted access area is where access

can only be gained by service personnel through the use of a special tool, lock and key, or other means

of security, and is controlled by the authority responsible for the location.

Voltage is present on the backplane when the system is operating. To reduce risk of an electric shock,

keep hands and fingers out of the power supply bays and backplane areas.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Before beginning the installation of the SCE 1000, read the Regulatory Compliance and Safety

Information for the Cisco Service Control Engine document.

Information About Preparing for Installation

• Site Preparation and Unpacking, page 1-1

• Tools and Parts, page 1-2

• Prepare for Rack-Mount Installation, page 1-2

Site Preparation and Unpacking

• Lift the SCE 1000 platform safely out of the packing container.

• Ensure the power service at the site is suitable for the SCE 1000 platform.

• Check the packing slip to ensure that all the proper components are present.

• Locate and have accessible the Site Log for recording information about this installation.

1-2

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 1 Prepare for Installation

Workbench or Tabletop Installation

Tools and Parts

Use the following list of tools and parts as a checklist for preparing for installing the SCE 1000 platform:

• Appropriate cables to connect the SCE 1000 to the network and console terminal

• Tape measure (optional)

• Level (optional)

• Number 1 Phillips screwdriver

• Number 2 Phillips screwdriver

• 1/4-inch flat-blade screwdriver

• 1/4-inch hex wrench

• Grounding kit (shipped with the SCE 1000)

• 12 AWG or 2.5 mm copper installation wire with hex or loop connectors for DC power leads (DC

power only) Ring terminals must be UL approved and suitable for 12 AWG wire.

• AC power cords (AC power only, shipped with SCE 1000)

• Rack-mounting kit (shipped with SCE 1000)

–

Spare screws for changing bracket position

Prepare for Rack-Mount Installation

Before you begin the rack-mounting tasks, determine the type of rack—four-post or two-post—that you

will be using.

Workbench or Tabletop Installation

Figure 1-1 Tabletop Installation of the SCE 1000 Platform

For a workbench or tabletop installation, verify the following before installing the SCE 1000 platform:

• The SCE 1000 platform is off the floor and has adequate ventilation.

C

is

c

o

S

C

E

1

0

S

eries

2

x

G

B

E

L

IN

K

R

X

T

X

R

X

M

T

X

L

IN

K

R

X

T

X

R

X

M

T

X

G

B

E

-1

S

U

B

L

IN

E

N

E

T

P

W

R

B

S

T

A

T

U

S

P

W

R

A

B

Y

P

A

S

1

0

/

1

0

/

1

0

L

I

N

K

/

A

C

T

I

V

E

1

0

/

1

0

/

1

0

L

I

N

K

/

A

C

T

I

V

E

AUX

C

O

N

S

O

L

E

MNG 2

MNG 1

1

2

92967

1-3

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 1 Prepare for Installation

Workbench or Tabletop Installation

• An adequate chassis ground (earth) connection exists for the SCE 1000 platform.

• The SCE 1000 platform has at least 2 inches (5 cm) of clearance at each side and at least 5 inches

(12.7 cm) of clearance at the rear to allow proper air flow.

Step 1 Remove the adhesive strips from the four rubber feet and affix the feet onto the four marked locations

on the bottom panel of the unit.

Step 2 Place the SCE 1000 platform on the tabletop or workbench.

1-4

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 1 Prepare for Installation

Workbench or Tabletop Installation

CHAPTER

2-1

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

2

Rack-Mount the SCE 1000

This section provides information for rack-mounting the SCE 1000 platform.

• The SCE 1000 Mounting Brackets

• Attach the Brackets to the SCE 1000

• Installing the Crossrail Supports (Four-post rack only)

• Mount the System to the Rack

The SCE 1000 Mounting Brackets

There are two standard types of equipment racks, and the appropriate brackets for each are provided in

the enclosed kit.

• 19” rack with front rack posts — the mounting kit includes two mounting brackets as illustrated

below:

Figure 2-1 Mounting Bracket for 2-post Racks

•

19” rack with front and back rack posts — in addition to the mounting brackets illustrated below,

the mounting kit includes two crossrail supports that the unit slides onto.

210429

2-2

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 2 Rack-Mount the SCE 1000

Attach the Brackets to the SCE 1000

Figure 2-2 Mounting Bracket for 4-post Racks

The SCE 1000 mounts to the two front rack posts with brackets that attach to the front of the SCE 1000

The inside width between the two posts or mounting strips (left and right) must be at least 17.3 inches

(44 cm).

Note Remember to leave a two-inch (5 cm) clearance on both sides of the SCE 1000 and at the rear for

adequate airflow for the inlet and exhaust vents.

Attach the Brackets to the SCE 1000

Before installing the SCE 1000 in the rack, you must first install an appropriate rack-mount bracket on

each side of the front of the SCE 1000, as illustrated in the following figures.

Figure 2-3 Attaching the Mounting Brackets (4-post)

210430

L

IN

K

R

X

T

X

R

X

M

T

X

L

IN

K

R

X

T

X

R

X

M

T

X

P

W

R

B

S

T

A

T

U

S

P

W

R

A

B

Y

P

A

S

10/100/

1000

LINK

/

AC

T

IV

E

10/100/

10

00

LIN

K/

AC

T

IVE

A

U

X

C

O

N

S

O

L

E

M

N

G

2

M

N

G

1

Cisco SCE 1000

S

e

r

i

e

s

2xG

BE

GBE-1

SUB LINE

NET

1 2

210418

2-3

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 2 Rack-Mount the SCE 1000

Installing the Crossrail Supports (Four-post rack only)

Figure 2-4 Attaching the Mounting Brackets (2-post)

To install the rack-mount brackets on the SCE 1000 chassis, complete the following steps:

Before installing the SCE 1000 in the rack, you must first install a rack-mount bracket on each side of

the front of the SCE 1000.

Step 1 Align the rack-mount bracket to the side of the SCE 1000. Choose the proper bracket for your installation

(2-post rack or 4-post rack) as illustrated in Rack-Mount the SCE 1000

Step 2 Insert and tighten three screws.

Step 3 Repeat steps 1 and 2 on the other side of the SCE 1000.

If mounting the SCE 1000 in a rack with only two posts, skip to Mount the System to the Rack.

If mounting the SCE 1000 in a rack with four posts, proceed to the next step, Installing the Crossrail

Supports (Four-post rack only).

Installing the Crossrail Supports (Four-post rack only)

This section provides information for assembling the crossrail supports and attaching them to the rack.

When mounting in a rack with four posts (front and back) the two crossrail supports are mounted one on

each side of the rack. The SCE 1000 then slides into these crossrails, which support the weight of the

unit.

• Assemble the Crossrail Supports

• Attach the Crossrail Supports to the Rack

Assemble the Crossrail Supports

Step 1 Assemble the two crossrail supports. Use three screws for each crossrail assembly.

L

I

N

K

R

X

T

X

R

X

M

T

X

L

I

N

K

R

X

T

X

R

X

M

T

X

P

W

R

B

S

T

A

T

U

S

P

W

R

A

B

Y

P

A

S

1

0

/

1

0

/

1

0

L

IN

K

/

A

C

T

IV

E

1

0

/

1

0

/

1

0

L

IN

K

/

A

C

T

I

V

E

A

U

X

C

O

N

S

O

L

E

M

N

G

2

M

N

G

1

Cisco SC

E

1000

Series

2xGBE

GBE-1

SUB

LINE

NET

210603

1 2

2-4

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 2 Rack-Mount the SCE 1000

Mount the System to the Rack

Figure 2-5 Assembling the Slider Brackets

Step 2

Make sure that they are oriented so that both crossrails will support the SCE 1000 when they are attached

to the rack.

Attach the Crossrail Supports to the Rack

Step 1 Align the crossrail supports with the side of the rack, parallel to the floor.

Figure 2-6 Attaching the Crossrails to the Rack

Step 2

Insert and tighten two screws to the front posts or mounting strips of the rack

Step 3 Insert and tighten two screws to the Back posts of the rack.

Step 4 Repeat steps 2 and 3 on the other side of the rack, keeping the brackets flush against the posts and

parallel to the supporting bracket on first side of the rack.

Mount the System to the Rack

When the appropriate mounting brackets are securely installed, the SCE 1000 can be installed into the

rack.

321

92777

321

92778

2-5

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 2 Rack-Mount the SCE 1000

Mount the System to the Rack

SUMMARY STEPS

1. Make sure that the rack brakes are locked or that the rack is otherwise stabilized.

2. Position the SCE 1000 so that the front end is closest to you, and lift it carefully to place it into the

rack. To prevent injury, avoid sudden twists or moves.

3. Slide the SCE 1000 into the rack, pushing it back until the brackets (installed at the front of the SCE

1000) meet the mounting strips or posts on both sides of the rack.

4. While keeping the brackets flush against the posts or mounting strips, align the holes in the brackets

with the holes on the rack or mounting strip.

5. For each bracket, insert and tighten two appropriate screws to the rack.

DETAILED STEPS

Step 1 Make sure that the rack brakes are locked or that the rack is otherwise stabilized.

Figure 2-7 Sliding the SCE Platform into the Rack

Step 2

Position the SCE 1000 so that the front end is closest to you, and lift it carefully to place it into the rack.

To prevent injury, avoid sudden twists or moves.

Step 3 Slide the SCE 1000 into the rack, pushing it back until the brackets (installed at the front of the SCE

1000) meet the mounting strips or posts on both sides of the rack.

L

I

N

K

R

X

C

i

s

c

o

S

C

E

2

0

S

e

r

i

e

s

4

x

G

B

E

T

X

R

X

M

T

X

L

I

N

K

R

X

T

X

R

X

M

T

X

L

I

N

K

R

X

T

X

R

X

M

T

X

L

I

N

K

R

X

T

X

R

X

M

T

X

G

B

E

-

1

S

U

B

L

I

N

E

N

E

T

P

W

R

B

S

T

A

T

U

S

P

W

R

A

B

Y

P

A

S

1

0

/

1

0

/

1

0

L

I

N

K

/

A

C

T

I

V

E

1

0

/

1

0

/

1

0

L

I

N

K

/

A

C

T

I

V

E

G

B

E

-

2

S

U

B

L

I

N

E

/

C

A

S

C

A

D

E

N

E

T

A

U

X

C

O

N

S

O

L

E

M

N

G

2

M

N

G

1

L

IN

K

R

X

T

X

R

X

M

MT

X

L

IN

K

R

X

T

X

R

X

M

T

X

P

W

R

B

S

T

A

T

U

S

P

W

R

A

B

Y

P

A

S

10/100/

1000

LIN

K

/

A

C

T

IV

E

10/1

00/

1000

LIN

K

/

A

C

T

IVE

A

U

X

C

O

N

S

O

L

E

M

N

G

2

M

N

G

1

Cisco SC

E 1000

S

e

r

i

e

s

2xG

BE

GBE-1

SUB

LINE

NET

1 2 3

210419

2-6

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 2 Rack-Mount the SCE 1000

Mount the System to the Rack

A rack with both front and back posts will have the crossrail supports installed. Slide the SCE 1000 onto

these crossrails and push it all the way back.

Step 4 While keeping the brackets flush against the posts or mounting strips, align the holes in the brackets with

the holes on the rack or mounting strip.

Figure 2-8 Securing the SCE Platform to the Rack

Step 5

For each bracket, insert and tighten two appropriate screws to the rack.

Note Since the brackets support the weight of the entire SCE 1000 chassis, be sure to use all four screws to

fasten the two rack-mount brackets to the rack posts.

L

IN

K

R

X

T

X

R

X

M

T

X

L

IN

K

R

X

T

X

R

X

M

T

X

P

W

R

B

S

T

A

T

U

S

P

W

R

A

B

Y

P

A

S

1

0/100/

1

000

L

IN

K/

ACTIV

E

10/10

0/

1

000

LINK

/

A

CTIV

E

A

U

X

C

O

N

S

O

L

E

M

N

G

2

M

N

G

1

Cisco SCE 1000

S

e

r

i

e

s

2xGBE

GBE-1

SUB LINE

NET

321

210420

CHAPTER

3-1

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

3

Connect the Power Supply Units

This section provides information for grounding the SCE 1000 platform and connecting the AC or DC

power supply units.

• Connect the Chassis Ground, page 3-1

• Connecting the Power, page 3-2

Connect the Chassis Ground

Figure 3-1 Grounding the Unit (AC)

IN PO

W

ER B O

K

IN

POW

ER A O

K

BYP

ASS 1

210421

21

3-2

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 3 Connect the Power Supply Units

Connecting the Power

Figure 3-2 Grounding the Unit (DC)

A Grounding kit is provided with each SCE 1000. Use this Grounding kit to properly ground the SCE

1000 chassis.

When installing the unit, the chassis ground connection must always be made first and disconnected last.

Step 1 On the rear panel of the SCE 1000, locate the chassis grounding connector (refer to the appropriate figure

for an AC- or DC-powered SCE 1000 above).

Step 2 Attach the grounding cable (green and yellow colored cable), firmly fastening the (enclosed) hex nuts

and spring washers with a #¼” hex wrench (refer to the appropriate figure for an AC- or DC-powered

SCE 1000 above).

The other side of the grounding cable must be connected to the site equivalent of the AC earth.

Connecting the Power

The following sections describe how to reconnect the AC or DC power:

• Connect the DC-Input Power Supply Unit, page 3-3

• Connect the AC-Input Power Supply Unit, page 3-4

IN

PO

W

ER

B

O

K

IN

PO

W

ER

A

O

K

BYP

ASS 1

210422

21

3-3

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 3 Connect the Power Supply Units

Connecting the Power

Connect the DC-Input Power Supply Unit

Figure 3-3 Connecting the DC Power

Before completing any of the following steps, and to prevent short-circuit or shock hazards, ensure that

power is removed from the DC circuit. To ensure that all power to the power supply unit is OFF, locate

the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF

position, and tape the switch handle of the circuit breaker in the OFF position.

Wiring should be done by a professional in accordance with state and local electrical codes.

Step 1 Ensure that the DC power line input leads are disconnected from the power source.

Step 2 Using the number 2 Phillips screwdriver, remove the protective plate from the terminal block.

Step 3 Insert one receptacle screw into the hex or loop connector on one power line input, insert the screw with

the connector into the corresponding lead receptacle and tighten the receptacle screw using the number

2 Phillips. Repeat for the remaining power line input lead.

Note The color coding of the DC-input power supply leads depends on the color coding of the DC power

source at your site. Make certain the lead color coding you choose for the DC-input power supply

matches lead color coding used at the DC power source.

Note Use 12 AWG (2.5 mm) copper wire only with hex or loop connectors. Ring terminals must be UL

approved and suitable for 12 AWG wire.

Step 4 Using the number 2 Phillips screwdriver, securely fasten the protective plate to the terminal block.

Step 5 Connect the DC power line input leads to the DC power source through a fast 10A circuit breaker.

Step 6 Turn the on/off switch to the on position.

IN POW

ER

BOK

IN

PO

W

ER

A

O

K

BYP

ASS 1

210424

3-4

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

OL-7822-06

Chapter 3 Connect the Power Supply Units

Connecting the Power

Step 7 Look at the IN and OK LEDs on the power supply unit and the corresponding Power LED on the front

panel. If the DC-input power supply unit is operating properly, these LEDs will be glowing green.

Step 8 Ensure that the power supply is properly aligned and the installation screw is tightened.

Connect the AC-Input Power Supply Unit

Step 1 Plug the AC-input power cable into the AC-input power receptacle on the AC-input power supply

For AC-input power, we recommend powering the SCE 2000 platform from a 120 VAC, 15A receptacle

U.S. (240 VAC, 10A international) at the power source.

Figure 3-4 Connecting the AC Power

Step 2

Plug the AC power supply cable into the AC power source.

Step 3 Turn the on/off switch to the on position.

Step 4 Look at the IN and OK LEDs on the power supply unit and the corresponding Power LED on the front

panel. If the AC-input power supply unit is operating properly, these LEDs will be glowing green.

Step 5 Ensure that the power supply is properly aligned and the installation screw is tightened.

IN PO

W

ER B O

K

IN

PO

W

ER A OK

BYPASS 1

210423

Page is loading ...

Cisco Systems OL-7822-06 User manual

Cisco Systems OL-7822-06 User manual

Related papers

Other documents