Frymaster MJCFE User manual

NON-CE &

Frymaster, a member of the Commercial Food Equipment Service Association, recommends

using CFESA Certified Technicians.

24-Hour Service Hotline 1-800-551-8633 APRIL 2005

PRINTED IN THE USA

www.frymaster.com

Email: [email protected]

*8195186*

Master Jet CF Series Atmospheric

Gas Fryers

Service & Parts Manual

Series MJCF, MJCFE, MJCFEC, FMCFE,

FMCFEC, JCFX, KJ3FC, J3F & J65X.

ii

Please read all sections of this manual and retain for future reference.

NOTICE

This appliance is intended for professional use only and is to be operated by qualified

personnel only. A Frymaster Factory Authorized Service Center (FASC) or other qualified

professional should perform installation, maintenance, and repairs. Installation, maintenance,

or repairs by unqualified personnel may void the manufacturer’s warranty.

NOTICE

Drawings and photos used in this manual are intended to illustrate operational, cleaning and

technical procedures and may not conform to onsite management operational procedures.

NOTICE

IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS

EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED

DIRECTLY FROM FRYMASTER/DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS,

AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS

WARRANTY WILL BE VOID. FURTHER, FRYMASTER/DEAN AND ITS AFFILIATES WILL NOT BE

LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH

ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF

ANY MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER.

DANGER

Improper installation, adjustment, maintenance or service, and unauthorized alterations or

modifications can cause property damage, injury, or death. Read the installation, operating and

service instructions thoroughly before installing or servicing this equipment. Only qualified

service personnel may convert this appliance to use a gas other than that for which it was

originally configured.

DANGER

Adequate means must be provided to limit the movement of this appliance without depending

upon the gas line connection. Single fryers equipped with legs must be stabilized by installing

anchor straps. All fryers equipped with casters must be stabilized by installing restraining

chains. If a flexible gas line is used, an additional restraining cable must be connected at all

times when the fryer is in use.

DANGER

The front ledge of the fryer is not a step. Do not stand on the fryer. Serious injury can result

from slips or contact with the hot oil.

DANGER

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other cooking appliance.

WARNING

No structural material on the fryer should be altered or removed to accommodate placement of

the fryer under a hood. Questions? Call the Frymaster Service Hotline at 1-800-551-8633.

iii

DANGER

Instructions explaining procedures to be followed MUST be posted in a prominent location in

the event the operator detects a gas leak. This information can be obtained from the local gas

company or gas supplier.

DANGER

The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container

at the end of frying operations each day. Some food particles can spontaneously combust if left

soaking in certain shortening material. Additional information can be obtained in the filtration

manual included with the system.

WARNING

Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to seal

the joint between the frypot. Banging fry baskets on the strip to dislodge shortening will distort

the strip, adversely affecting its fit. It is designed for a tight fit and should only be removed for

cleaning.

IMPORTANT

Safe and satisfactory operation of Frymaster equipment depends upon its proper installation.

Installation MUST conform with local codes, or in the absence of local codes, to European

Community (CE) Standards.

COMPUTERS

FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference

received, including interference that may cause undesired operation. While this device is a verified Class

A device, it has been shown to meet the Class B limits.

CANADA

This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set out by the

ICES-003 standard of the Canadian Department of Communications.

Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de classe A et B

prescrites dans la norme NMB-003 edictee par le Ministre des Communcations du Canada.

DANGER

THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE

CANCER AND/OR BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

Operation, installation, and servicing of this product could expose you to airborne particles of

glasswool or ceramic fibers, crystalline silica, and/or carbon monoxide. Inhalation of airborne

particles of glasswool or ceramic fibers is known to the State of California to cause cancer.

Inhalation of carbon monoxide is known to the State of California to cause birth defects or other

reproductive harm.

iv

Master Jet CF Series Atmospheric Gas Fryers

TABLE OF CONTENTS

PAGE #

1.

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.8.1

1.8.2

1.8.3

1.8.4

1.8.5

1.8.6

1.8.7

1.8.8

1.8.9

1.8.10

1.8.11

1.8.12

1.9

1.9.1

1.9.2

1.9.3

1.9.4

1.9.5

1.9.6

1.9.7

1.10

1.10.1

1.10.2

1.11

1.12

1.12.1

1.12.2

1.12.3

1.12.4

1.12.5

SERVICE PROCEDURES

Functional Description

Accessing Fryers for Servicing

Cleaning Burner Manifold Gas Pressure

Adjusting Pilot Flame

Cleaning Gas Valve Vent Tube

Adjusting Burner Ceramic Target Spacing and Alignment

Calibrating Thermostat Control

Replacing Fryer Components

Replacing Computer

Replacing Operating Thermostat

Replacing Temperature Probe

Replacing High-Limit Thermostat – Operating Thermostat Controls

Replacing High-Limit Thermostat – Computer Controls

Replacing Heat Mode Indicator Light – Operating Thermostat Controls

Replacing Power/Melt Cycle Switch – Operating Thermostat Controls

Replacing Melt Cycle Timer – Operating Thermostat Controls

Replacing Burner Ceramic Targets

Replacing Gas Valve

Replacing Pilot Assembly or Thermopile

Replacing Frypot

Troubleshooting and Problem Isolation

Pilot/Ignition Failures

Improper Burner Functioning

Improper Temperature Control

Computer Related Problems

Filtration Problems

Leakage Problems

Millivolt Problems

Troubleshooting Guides

Initial Troubleshooting, Millivolt Frying Systems

Initial Troubleshooting, 24VAC Frying Systems

Probe Resistance Chart

Wiring Diagrams

MJCF Millivolt Wiring Diagram, Non-CE

MJCF Millivolt Wiring Diagram, CE

MJCFE 24V Wiring Diagram

MJCFEC 24V Wiring Diagram

FAST-Ready Constant Pilot

1–1

1–4

1–5

1–6

1–7

1–8

1–9

1–10

1–11

1–12

1–13

1–14

1–15

1–17

1–18

1–20

1–22

1–23

1–24

1–26

1–28

1-28

1–31

1–33

1–34

1–32

1–35

1–36

1–37

1–38

1–39

v

Master Jet CF Series Atmospheric Gas Fryers

TABLE OF CONTENTS (cont.)

PAGE #

1.12.6

2.

2.1

2.2

2.3

2.3.1

2.3.2

2.4

2.5

2.5.1

2.5.2

2.5.3

2.6

2.7

2.7.1.1

2.7.1.2

2.7.2

2.7.3

2.7.4

2.7.5

2.7.6

2.7.7

2.7.8.1

2.7.8.2

2.7.9

2.8

2.9

A.

A.1

A.1.1

A.1.2

A.1.3

A.1.4

A.1.5

A.1.6

A.1.7

A.2

Filter Magic II Wiring Diagram

PARTS LIST

Accessories

Burner Manifold Components

Cabinetry Components

Fryer Cabinetry

Filter Magic II and Spreader Cabinet Cabinetry

Casters, Legs and Associated Hardware

Component Shield, Filter Box Assemblies and Components

Component Shield Assemblies – No Interface Board

Component Shield Assemblies – With Interface Board

Filter Box Assemblies

Control Panel Assemblies and Related Components

Filtration System Components

Filter Magic II Drain Manifold Components

Euro-Look Drain Manifold Components

Filter Magic II Filter Pan Components – Outer Pan Components

Filter Magic II Filter Pan Components – Inner Pan Components

Oil Return Handle Components – Units Built Prior to April 2001

Oil Return Handle Components – Units Built April 2001 and After

Oil Return Plumbing

Filter Pump and Motor Components

Drain Valves and Related Components

Euro-Look Drain Valves and Related Components

Power Shower Components

Frypot, High-Limit and Probe Components

Wiring Connectors, Pin Terminals and Power Cords

APPENDIX

KJ3FC & J3F Variants – Wiring Diagrams

Computer Wiring Diagram – KJ3FC Fast-Ready

J3F Wiring Diagram – (Fast/Fast-Computer Modified; For Reference Only)

KFC-1 Computer Wiring Diagram – 120V

KFC-1 Computer Wiring Diagram – 220V

KSCF Wiring Diagram w/ Float (CE)

KFC-1 Harness Diagram

Transformer/Filter Box Wiring for FAST Controller

Parts List – KJ3FC Variant

1–40

2–1

2–3

2–5

2–7

2–9

2–10

2–11

2–12

2–13

2–15

2–17

2–18

2–19

2–21

2–22

2–23

2–24

2–26

2–27

2–28

2–29

2–31

A–1

A–2

A–3

A–4

A–5

A–6

A–7

A–8

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-1

1.1 Functional Description

Master Jet (MJ) CF Series Atmospheric gas fryers contain a welded stainless steel frypot that is

directly heated by gas flames that are diffused evenly over its lower surface by ceramic targets.

The flames originate from orifices in a U-shaped burner manifold positioned beneath the frypot. The

orifice diameters differ for natural and propane gas as shown in the table below. For altitudes of

2000 feet and greater, contact factory for correct orifice part number.

Gas Inches Millimeters

Natural 0.055 1.4

Propane 0.035 0.9

CF Series Orifice Sizes (0-1999 ft/609 m)

Gas flow to the manifold is regulated by an electromechanical gas valve. MJCF Series gas fryers are

equipped with millivolt gas valves, and MJCFE Series gas fryers are equipped with 24-volt gas

valves. All models use a pilot ignition system.

Pilot Ignition System

The pilot ignition system consists of the pilot orifice, pilot hood, and a thermopile (a thermocouple is

also used in CE units per CE requirements). The pilot serves two purposes. The first is to light the

burner, the second is to heat the thermopile. In operation, the thermopile is in contact with the pilot

flame and generates millivolts. The millivolt output passes through a normally closed high-limit

switch and energizes the gas valve pilot coil, which in turn opens the pilot valve. If the pilot flame is

extinguished, voltage is lost to the gas valve pilot coil and the pilot valve closes.

On MJCFE models, a separate 24-volt circuit,

activated by the fryer On/Off switch,

provides voltage through the thermostat or

controller to the gas valve main coil, which

opens the main valve. The gas valve is

constructed so that the main valve will not

open if the pilot valve is not open. The pilot

flame must be manually lit (either with a

match or with an optional built-in piezo

ignitor) when the fryer is first placed into

operation.

High-Limit

Main Valve Magnet

Pilot Magnet

Thermopile

Pilot

Gas Valve

Operating Thermostat

24VAC Transformer

Line Voltage

ON/OFF Switch

The Pilot System (24V Circuit, Non-CE).

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-2

1.1 Functional Description (cont.)

CONTROL OPTIONS

MJCF Series gas fryers may be equipped with thermostat controllers or Computer Magic III.5

computers. KJ3FC variants are equipped with user-supplied or KFC-1 computers.

MJCF fryers equipped with thermostat controls are turned on and off with the gas valve control knob

(an On/Off switch is optional). The temperature is set by means of a knob connected directly to the

frypot-mounted thermostat. MJCFE models come equipped with a rocker switch to turn the fryer on

and off. Units equipped with thermostat controllers have no interface board.

MJCFE Series with Melt-Cycle option: When the melt cycle switch is placed in the ON position, the

fryer stays in the melt cycle mode until the switch is manually placed in the OFF position, even if the

frypot is at setpoint temperature.

Fryers equipped with computers have an interface board located in the component shield behind the

control panel.

INTERFACE BOARDS

The interface board provides the link between the computer and the fryer’s components without

requiring excessive wiring, and allows the computer to execute commands from one central point.

Depending upon the configuration of the fryer, any of three boards may be used. Regardless of the

particular board installed when the fryer was built, P/N 806-3548 is the universal replacement

part (not applicable to user-supplied computers).

NOTES:

1. RELAYS K1 AND K2 ARE FOR BELL CRANK BASKET LIFTS.

THEY ARE NOT PRESENT ON BOARDS 806-5490 (U.S. & NON-

CE EXPORT UNITS W/O BASKET LIFTS) OR 806-7501 (CE UNITS,

WITH OR WITHOUT BASKET LIFTS).

2. RESISTORS R1, R10, AND R15 ARE NOT USED ON ANY OF THE

THREE BOARDS.

3. RESISTORS R11 AND R12 ARE NOT USED ON 806-5490

BOARDS.

INTERFACE BOARDS 806-3548, 806-5490 & 806-7505

1

K3

SOUND

R17

R15

R16

2

3

K2 K1

3

4

52

1

C

R13

D8

2000

R9

C1

R10

COMP AC

D7

R4

D5

R2

R3

24VAC

R8

R12

D6

GV

D4

R6

AL 24V

J2

Frymaster

R14

MADE IN U.S.A.

HOT

AC

D9

AC

COM

HOT

J1

R7

R1

R5

COM

COMP

D1

R11

1

3

4

52

1

3

4

52

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15 1

2

3

4

5

6

7

8

9

10

11

12

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-3

1.1 Functional Description (cont.)

Test

Meter

Setting Pins Results

12 VAC Power to Controller 50 VAC Scale 1 and 3 of J2 12-18

24 VAC Power 50 VAC Scale 24 VAC Terminals 22-28

24 VAC Power to Gas Valve 50 VAC Scale 6 on J1 and GROUND 22-28

120 VAC Power 250 VAC Scale 7 and 12 of J1 110-125

Probe Resistance* R x 1000 OHMS 2 and 3 of J1 **

FREQUENTLY USED TEST POINTS FOR MODELS WITH INTERFACE BOARDS

** Disconnect 15-Pin harness from controller before testing probe circuit.

** See Probe Resistance Chart at end of chapter.

Four LEDs, arranged across the top of the boards and identified in the table below, are provided to

assist in troubleshooting.

GV

Indicates 24 VAC to the gas valve

AL

Indicates open Drain Safety Switch (if installed)

24V

Indicates 24 VAC from transformer

COMP

Indicates 12 VAC to computer

MASTER JET SERIES INTERFACE BOARD

LED DIAGNOSTIC LIGHTS

Every board contains one heat relay (K3), and may contain two basket lift relays (K1 and K2). As

shipped from the factory, fryers with bell-crank basket lifts will have relays K1, K2, and K3. All

other factory-original fryers will have boards with only relay K3.

NOTE: The basket lift option is not available on MJCF Series fryers. The above diagnostic

tables are not applicable to user-supplied or KFC-1 computers.

THERMOSTATS AND TEMPERATURE PROBES

MJCF Series fryers equipped with thermostat controls have an adjustable controlling (operating)

thermostat. The temperature at which the thermostat opens and closes is adjusted by changing the

setting of the thermostat with an attached knob. When new, the Fenwal controlling thermostat is

sensitive to one-degree changes in temperature.

CAUTION

Fenwal thermostats are used in a number of Frymaster products. The thermostat for

the MJCF Series is 4 inches long. Do not use 3-inch Fenwal thermostats in MJCF

Series fryers.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-4

1.1 Functional Description (cont.)

MJCFE Series fryers equipped with computers have a temperature probe. In these units, the probe

resistance varies directly with the temperature. That is, as the temperature rises, so does resistance at

a rate of approximately 2 ohms for every 1° (F or C). Circuitry in the computer monitors the probe

resistance and controls burner firing when the resistance exceeds or falls below programmed

temperatures (setpoints). The temperatures are programmed by means of a keypad on the face of the

computer.

All MJCF Series Atmospheric gas fryers are equipped with a high-limit thermostat. In the event

that the fryer fails to properly control the oil temperature, the high-limit thermostat prevents the fryer

from overheating to the flash point. The high-limit thermostat acts as a normally closed power

switch that opens when exposed to temperatures in the range of 415°F to 435°F (213°C to 224°C).

The high-limit thermostat is the same for CE and Non-CE applications. When a replacement high-

limit thermostat is ordered, ensure the kit appropriate for the valve in use is ordered.

1.2 Accessing Fryers for Servicing

DANGER

Moving a fryer filled with oil may cause spilling or splattering of hot liquid. Follow

the draining instructions in the Operator’s manual that shipped with the fryer.

1. Shut off the gas supply to the unit. Unplug the power cord(s). Disconnect the unit from the gas

supply.

2. Remove any attached restraining devices.

3. Relocate the fryer for service accessibility.

4. After servicing is complete, reconnect the unit to the gas supply, reattach restraining devices,

and plug in the electrical cords.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-5

1.3 Checking Burner Manifold Gas Pressure

WARNING

This task should be performed by qualified service personnel only.

1. Ensure that the gas valve knob or button is in the OFF position.

2. Remove the pressure tap plug from the end of the manifold (see illustration below) and connect a

gas pressure-measuring device to the port.

Remove plug to connect a gas

pressure-measuring device to the port.

3. Place the gas valve in the ON position then place the fryer power switch in the ON position

(where applicable). When the burner lights and continues to burn, compare the pressure reading

to that for the corresponding gas in the tables below and on the next page.

Model

Gas Type G20 G25 G31

Pressure

(

mbar

)

1

20 20-25 37-50

Number

of

Orifices

21 21 21

Manifold

Pressure

7,5 10 14,9

CE Standards for Incoming Gas

Pressures

MJCF/J65 CE

Orifice

Size

1,40 1,40 0,95

1

(mbar) = 10,2 mm CE

Air Flow

(

m

3

/

H

)

3,62 4,18 2,35

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-6

1.3 Checking Burner Manifold Gas Pressure (cont.)

Non-CE Standard

for Incoming Gas Pressures

Gas Minimum Maximum

Natural

6" W.C.

1.49 kPa

14.93 mbar

14" W.C.

3.48 kPa

34.84 mbar

LP

11" W.C.

2.74 kPa

27.37 mbar

14" W.C.

3.48 kPa

34.84 mbar

Gas

Natural

LP

8.25" W.C.

2.0 kPa

20.0 mbar

Pressure

Non-CE Standard

3.5" W.C.

.75 kPa

7.5 mbar

for Burner Manifold Gas Pressures

4. If the measured manifold gas pressure does not match the appropriate pressure in the preceding

tables, remove the cap from the gas valve regulator and adjust to the correct pressure.

Honeywell Valve

(Non-CE Units)

Honeywell Valve

(CE Units)

Regulator Adjustment Screw Cap

1.4 Adjusting Pilot Flame

1. On non-CE valves, remove the cap covering the pilot adjustment screw. On all valves, turn the

pilot adjustment screw counterclockwise to increase the length of the flame or clockwise to

decrease the length of the flame. Adjust the flame to a length of 1 to 1-½ inches (25 to 38 mm).

Honeywell Valve

(Non-CE Units)

Honeywell Valve

(CE Units)

Pilot Adjustment Screw

On Non-CE gas valves, remove this cap to

access Pilot Adjustment Screw.

2. On Non-CE valves, reinstall the pilot adjustment screw cap.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-7

1.5 Cleaning Gas Valve Vent Tube

1. Carefully unscrew the vent tube from the gas valve. NOTE: The vent tube may be straightened

for ease in removal.

2. Pass a piece of ordinary binding wire (.052 inch diameter) or equivalent through the tube to

remove any obstruction.

3. Remove the wire, and then blow through the tube to ensure it is clear.

4. Reinstall tube and bend it so that the opening is pointing downward.

1.6 Adjusting Burner Ceramic Target Spacing and Alignment

DANGER

Drain the frypot or remove the handle from the drain valve before proceeding further.

Proper spacing of the top edge of the burner ceramic targets is ¾-inch (13 mm) from the frypot side

[The rear target should be adjusted to 1-inch (25 mm) from the frypot back]. To adjust target

spacing, bend the brackets to which they are attached away or toward the frypot to the proper

distance. (A length of board of the proper thickness is useful as a gauge to verify spacing and

alignment.)

There should be about 3/4-inch spacing between the top edge of the targets

and the side of the frypot, and 1-inch between the rear target and the frypot

back.

3/4-inch

1-inch

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-8

1.7 Calibrating Thermostat Control

1. Fill the frypot to the lower OIL-LEVEL line with oil. If solid shortening is used, it must be

tightly packed into the frypot.

2. Light the pilot. (Refer to Installation and Operation Manual that shipped with the fryer for

detailed lighting instructions.)

3. Insert a good grade thermometer or pyrometer into the frypot, about one inch from the

thermostat.

4. Set the thermostat to 325°F (163°C).

5. Allow the fryer to heat to 325°F (163°C) and cycle on and off three times.

6. With the oil temperature at 325°F (163°C) turn the flexible shaft slowly clockwise until the

burner shuts off. (Turning the shaft counterclockwise causes the temperature to increase and the

burner to light; turning it clockwise causes the temperature to decrease and shut off.)

7. Allow the fryer to sit for a few minutes and then slowly turn the flexible shaft counterclockwise

until the burner lights.

8. Repeat steps 6 and 7 at least three times to ensure an accurate setting is obtained. The thermostat

control is calibrated if the burner lights as the oil cools to 325°F (163°C) – not when the burner

shuts off as the temperature rises.

9. Compare the reading of the pyrometer to the setting on the thermostat plate. The position of the

knob on the thermostat and the reading from the pyrometer should be within 5°F (3°C) of each

other.

10. If not, loosen the setscrew and stop screw securing the thermostat shaft extension to the flexible

shaft. Remove the extension to expose the slot in the end of the flexible shaft. Use a flat-blade

screwdriver to adjust the thermostat.

11. Once the calibration point of 325°F (163°C) is determined, allow the burner to cycle on and off

at least three times to ensure it will light at the calibrated temperature.

12. Carefully replace the thermostat shaft extension, ensuring that the stop screw is pointed straight

up. Tighten the stop screw and locking nut and the setscrew, being careful not to rotate the

flexible shaft.

CAUTION

The thermostat flexible shaft must not be rotated while installing the thermostat

shaft extension!

When handling the thermostat, do not rotate the shaft more than two turns in either

direction. Doing so will cause damage to the thermostat.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-9

1.7 Calibrating Thermostat Control (cont.)

13. Close the fryer control panel and replace the screws in the upper corners.

14. Reinstall the thermostat knob with its pointer aligned with the 325°F (163°C) index mark on the

temperature dial.

15. Reconnect the fryer to the electrical power supply.

1.8 Replacing Fryer Components

1.8.1 Replacing Computer

1. Disconnect the fryer from the electrical

supply.

2. The controller bezel is held in place by

tabs at the top and bottom. Slide the

bezel up to disengage the lower tabs.

Then slide the bezel down to disengage

the upper tabs.

3. Remove the two screws in the upper

corners of the control panel and swing

the panel open from the top, allowing it

to rest on its hinge tabs.

4. Disconnect the wiring harness from the

back of the controller and, if replacing

the harness, disconnect it from the

interface board (arrows).

5. Disconnect the ground wire, and then

remove the controller by lifting it from

the hinge slots in the control panel

frame.

6. Ensure the new computer is properly

configured for the fryer on which it is

installed (i.e., gas or electric, full or

split pot and Celsius or Fahrenheit.

Although identical in appearance,

computers configured for use on one

type of fryer are not directly

interchangeable with those configured

for use on another type.

7. Reverse the procedure to install a new

controller or wiring harness.

If replacing harness, disconnect the harness from

the controller and interface board (arrows).

If replacing controller, disconnect the ground wire

and the 15-pin connector (arrows).

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-10

1.8.2 Replacing Operating Thermostat

CAUTION

The thermostat must be calibrated after installation is complete. Refer to Section 1.7

for calibration instructions.

When handling the thermostat, do not rotate the shaft more than two turns in either

direction. Doing so will cause damage to the thermostat.

1. Disconnect the fryer from the electrical supply and drain the frypot.

2. Loosen the setscrew securing the thermostat knob and remove the knob. Remove the screws

from the upper left and right corners of the control panel. The control panel is hinged at the

bottom and will swing open from the top.

3. Disconnect the 9-pin connector and remove the control panel from the fryer by disengaging its

tabs from the hinge slots in the mounting frame.

4. Loosen the setscrews (2) securing the

flexible shaft to the thermostat shaft and

slip the flexible shaft off the thermostat

shaft (arrow).

5. Remove the flexible shaft guide by

removing the two sheet metal screws

securing it to the upper frame.

6. Disconnect the thermostat leads from pin

14 in the 20-pin terminal block and from

the gas valve terminal.

NOTE: If the fryer is configured with a

melt cycle, the thermostat leads will be

connected to the melt cycle timer motor

or PC board rather than to the terminal

block and gas valve. Disconnect the leads

from the motor or PC board if this is the

case.

7. Unscrew the thermostat from the frypot and remove.

8. Apply Loctite PST567 thread sealant or equivalent to the replacement thermostat threads.

9. Reverse steps 1 through 7 to install the replacement.

Remove setscrews (arrow) to remove flexible shaft

from thermostat shaft.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-11

1.8.3 Replacing Temperature Probe

1. Disconnect the fryer from the electrical supply.

2. Drain the frypot.

3. Remove the screws from the upper left and right corners of the control panel. The panel is

hinged at the bottom and will swing open from the top.

4. Unplug the wiring harness from the back of the controller and disconnect the grounding wire

(see Section 1.8.1, Step 4).

5. Remove the controller from the fryer by lifting it from the hinge slots in the control panel frame.

5. Remove the two screws from the base of the interface board mounting-bracket.

6. Disconnect the 12-pin plug from the back of the interface board and lay the board in the left end

of the compartment with all other wires still connected.

7. Remove the 12-volt transformer from the component shield and lay it in the left end of the

compartment with wires still connected.

8. Using a pin-pusher, remove the temperature probe wires (pins 1 and 2) from the 12-pin plug

disconnected in step 7.

9. Unscrew the temperature probe from the frypot and remove.

10. Apply Loctite PST567 thread sealant or equivalent to new probe threads.

11. Reverse steps 1 through 10 to install the replacement probe.

1.8.4 Replacing High-Limit Thermostat – Operating Thermostat Controls

1. Disconnect the fryer from the electrical supply.

2. Drain the frypot.

3. Loosen the setscrew securing the thermostat knob and remove the knob. Remove the screws

from the upper left and right corners of the control panel. The control panel is hinged at the

bottom and will swing open from the top.

4. Disconnect the 9-pin connector and remove the control panel from the fryer by disengaging its

tabs from the hinge slots in the mounting frame.

5. Disconnect the high-limit thermostat leads from the gas valve pilot coil.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-12

1.8.4 Replacing High-Limit Thermostat – Operating Thermostat Controls (cont.)

6. Unscrew the high-limit thermostat from the frypot and remove.

7. Apply Loctite PST567 thread sealant or equivalent to the replacement thermostat threads.

8. Reverse steps 1 through 7 to install the replacement.

1.8.5 Replacing High-Limit Thermostat – Computer Controls

1. Disconnect the fryer from the electrical power supply.

2. Drain the frypot.

3. Remove the screws from the upper left and right corners of the computer panel. The computer is

hinged at the bottom and will swing open from the top.

4. Unplug the wiring harness and disconnect the grounding wire from the controller.

5. Remove the controller from the fryer by lifting it from the hinge slots in the fryer control panel

frame.

6. Remove the two screws from the base of the interface board-mounting bracket.

7. Disconnect the 12-pin plug from the back of the interface board and lay the board in the right end

of the compartment with all other wires still connected.

8. Remove the 12-volt transformer and lay it in the right end of the compartment with wires still

connected.

9. Remove the high-limit thermostat wires from the gas valve pilot coil and pull them up through

the control shield.

10. Unscrew the high-limit thermostat from the frypot and remove.

11. Apply Loctite PST567 thread sealant or equivalent to the replacement thermostat’s threads and

screw it into the frypot.

12. Attach the appropriate terminals (furnished in the replacement thermostat kit) to the thermostat

leads.

13. Reverse steps 1 through 9 to complete installation of the replacement thermostat.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-13

1.8.6 Replacing Heat Mode Indicator Light – Operating Thermostat Controls

1. Disconnect the fryer from the electrical supply.

2. Loosen the setscrew securing the thermostat knob and remove the knob. Remove the screws

from the upper left and right corners of the control panel. The control panel is hinged at the

bottom and will swing open from the top.

3. Disconnect the 9-pin connector and remove the control panel from the fryer by disengaging its

tabs from the hinge slots in the mounting frame.

4. Carefully press the light out from the back of the control panel. Disconnect one wire at a time

and reconnect it to the replacement light until all wires are transferred.

5. Carefully press the light back into the control panel.

6. Reverse steps 1-3 to reassemble the fryer.

1.8.7 Replacing Power/Melt Cycle Switch – Operating Thermostat Controls

NOTE: The Power/Melt-Cycle Switch, P/N 807-1404, has been replaced with a new switch, P/N

807-3498. When ordering the new switch, order Kit 826-1792, which contains the new switch and

wiring instructions. The new switch is wired differently than the old one. Ensure the new switch is

wired properly before operating fryer. Consult P/N 819-5889 (MJCF, MJ45 Switch Replacement

Instructions) for further detail.

1. Disconnect the fryer from the electrical supply.

2. Loosen the setscrew securing the thermostat knob and remove the knob. Remove the screws

from the upper left and right corners of the control panel. The control panel is hinged at the

bottom and will swing open from the top.

3. Disconnect the 9-pin connector and remove the control panel from the fryer by disengaging its

tabs from the hinge slots in the mounting frame.

4. Using a flat-tipped screwdriver, disconnect the chrome bezel from the tabs on the switch and

press the switch out from the front.

5. Carefully press the new switch back into the chrome bezel, ensuring the tabs on the switch

engage the slots in the bezel.

6. Disconnect the wires from the old switch and reconnect to the new switch until all wires have

been transferred (see note at the beginning of this procedure).

7. Reverse steps 1-3 to reassemble the fryer.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-14

1.8.8 Replacing Melt Cycle Timer – Operating Thermostat Controls

The mechanical melt cycle timer is no longer available. A solid-state timer replaces the

mechanical unit. To replace the mechanical melt-cycle timer:

1. Remove all electrical power from the fryer. Unplug fryer and ensure all power switches are off.

2. Access timer by removing the control

panel. Remove timer by removing two

screws that hold it in place. Detach wires.

3. Attach wires to the new timer as follows:

Ground -To number 4 of clip terminals.

24VAC - To wire 28C.

Melt - To wire 29C.

Valve - To thermostat.

4. Bolt new timer into place. Reattach

control panel.

Remove the control panel to reveal the mechanical

timer (arrow). The metal plate that holds the timer-

unit in place is secured with two screws. Remove

the screws, lift out the timer and detach the wires.

The solid-state timer mounted on a metal plate,

bolts into the space previously occupied by the

mechanical timer.

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1-15

1.8.9 Replacing Burner Ceramic Targets

DANGER

Drain the frypot or remove the handle from the drain valve before proceeding further.

1. Disconnect fryer from electrical and gas supplies.

2. On FMCF fryers, remove square-drain sections as necessary to expose burner.

3. Disconnect the wires from the gas valve terminal block, marking each wire to facilitate

connections.

4. Remove the high-limit thermostat wires from the gas valve pilot coil.

5. Disconnect the pipe union collar at the left side of the gas valve (arrow).

6. Remove front burner shields to access burner assembly.

7. Remove the burner heat shield hanger screws at the front of the burner and remove the heat

shield.

8. Remove the burner hanger screws and lower the front of the main burner. Pull it forward to clear

the rear burner hanger, and then lower the burner to the floor.

9. Raise the front of the fryer enough to slide the burner from under the fryer cabinet.

Disconnect union (arrow) to remove burner manifold assembly.

Page is loading ...

Frymaster MJCFE User manual

Related papers

Other documents