Columbia SANI-LAV 505FL Operating instructions

Columbia
Brand
Columbia
Model
SANI-LAV 505FL
Category
Faucets
Type
Operating instructions

Columbia SANI-LAV 505FL is a wall-mounted sink designed for commercial use. It is made of stainless steel and has a 2" drain hole. The sink is NSF/ANSI Standard 2 and NSF/ANSI 372 certified, meaning that it is safe for use in food preparation areas and contains less than 0.25% lead in wetted surfaces. The sink comes with a faucet mounting kit, a wall-mounting bracket, two support brackets, a strainer assembly with basket, and all necessary hardware. It is easy to install and can be mounted on any wall. The sink is also easy to clean and maintain.

Columbia SANI-LAV 505FL is a wall-mounted sink designed for commercial use. It is made of stainless steel and has a 2" drain hole. The sink is NSF/ANSI Standard 2 and NSF/ANSI 372 certified, meaning that it is safe for use in food preparation areas and contains less than 0.25% lead in wetted surfaces. The sink comes with a faucet mounting kit, a wall-mounting bracket, two support brackets, a strainer assembly with basket, and all necessary hardware. It is easy to install and can be mounted on any wall. The sink is also easy to clean and maintain.

1
WALL MOUNTED SINKS
Operating Manual for Wall Mounted Sinks
Models 505FL and 505FL-0.5
Columbia does not recommend use with harsh chemicals.
NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.
2
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: 949.474.0777 Toll Free: 800.626.2117 Fax: 949.474.1191 www.columbiasinks.com email: info@columbiasinks.com
©2019 Columbia Products
WALL MOUNTED SINKS
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Measure a recommended 41.5” from finished floor and draw a level line which will be the top
edge of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill holes
and secure bracket to the wall as shown in illustration A. Screws are not provided.
Step 2
1. Install faucet assembly to the sink using the faucet mounting kit model SMK.
2. Install strainer assembly at the drain hole.
3. Connect hot and cold water supply (not included) to the faucet.
Step 3
1. Position the sink onto wall bracket.
2. Mark holes for fastening side mounting brackets as shown in illustration B.
3. Remove sink from the wall bracket.
4. Drill holes in wall for securing sink to wall.
5. Hang sink on the wall bracket and secure to the wall.
Step 4
1. Connect waste line or drain pipe to the strainer assembly.
2. Connect hot and cold water supply lines to the water source.
3. Remove aerator from the spout and flush water system.
4. Check connections for leaks.
5. Replace aerator onto the spout.
Parts List
(1) Wall mount sink
(1) 8” on center faucet
(1) Faucet mounting kit
(1) Wall-mounting bracket
(2) Support brackets
(1) Strainer assembly with basket
Tools Required
Tape Measure
Adjustable Wrench
Drill Motor and Drill Bits
Pipe Wrench
Level
Safety Glasses
Screw Drivers: 1 Phillips & 1 Standard
Pencil
Socket Wrench
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from the
spout or from under
the lever.
1. Seat washer is worn
2. Seat is worn
3. O-rings are worn
Shut cold water source off. See if water still leaks from the spout.
If leaks continues repair hot side if not repair cold side.
Recommend installing hot or cold
faucet repair kit.
Illustration A
Illustration B
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
16.5”
(419mm)
21”
(533mm)
45º
507F
5.5”
(140mm)
5.5”
(140mm)
8”
(203mm)
4” (102 mm)
19” (483mm)
17.875” (454mm)
6.125” (156mm)
7.5” (191mm)
17” (432mm)
2” drain hole
Stainless Steel Brackets
9.5”
(241mm)
7”
(197mm)
1.25” R
6mm
Hole Configurations
Front Side
Top
wall hanger
.875” (22mm)
dia. hole
6” (152mm)
9.5” (241mm)
5.5” (140 mm)
18”
(457mm)
14”
(356mm)
2” (51mm)
Supply Line Detail
2” (51mm)
1.5” (38mm)
back splash
.25” dia. hole
wall hanger
Wall Mounting Detail
Back Splash
1/2” Male NPT
Hot
from Wall
Cold
from Wall
3
COLUMBIA SPECIFICATIONS
1622 Browning Irvine, CA 92606-4809 Phone: 949.474.0777 Toll Free: 800.626.2117 Fax: 949.474.1191 www.columbiasinks.com email: info@columbiasinks.com
©2019 Columbia Products
WALL MOUNTED SINKS
  • Page 1 1
  • Page 2 2
  • Page 3 3

Columbia SANI-LAV 505FL Operating instructions

Columbia
Brand
Columbia
Model
SANI-LAV 505FL
Category
Faucets
Type
Operating instructions

Columbia SANI-LAV 505FL is a wall-mounted sink designed for commercial use. It is made of stainless steel and has a 2" drain hole. The sink is NSF/ANSI Standard 2 and NSF/ANSI 372 certified, meaning that it is safe for use in food preparation areas and contains less than 0.25% lead in wetted surfaces. The sink comes with a faucet mounting kit, a wall-mounting bracket, two support brackets, a strainer assembly with basket, and all necessary hardware. It is easy to install and can be mounted on any wall. The sink is also easy to clean and maintain.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents