Electro-Voice AGSE Adaptor Grid Operating instructions

Electro-Voice
Brand
Electro-Voice
Model
AGSE Adaptor Grid
Category
Soundbar speakers
Type
Operating instructions

This manual is also suitable for

Electro-Voice AGSE Adaptor Grid allows for the integration of an XLE Array with an X-Line Very Compact Subwoofer Array. The rigging attachment positions on the adapter grid and enclosures allow for the the combination array to be splayed or tilted to obtain the desired sound coverage. The adapter grid allows for 2 options:

  1. Flying XLE Arrays below X-Line Very Compact Subwoofers, using the XLD Grid.
  2. Stack XLE Arrays above X-Line Very Compact Subwoofers, using the XGS-4 Groundstack.

Electro-Voice AGSE Adaptor Grid allows for the integration of an XLE Array with an X-Line Very Compact Subwoofer Array. The rigging attachment positions on the adapter grid and enclosures allow for the the combination array to be splayed or tilted to obtain the desired sound coverage. The adapter grid allows for 2 options:

  1. Flying XLE Arrays below X-Line Very Compact Subwoofers, using the XLD Grid.
  2. Stack XLE Arrays above X-Line Very Compact Subwoofers, using the XGS-4 Groundstack.
AGSE Grid
X-Line Very Compact
AGSE Adapter Grid
User Instructions
AGSE Adapter Grid
The AGSE Adapter Grid allows for the flexibility of integrating an XLE Array with an X-Line Very Compact Subwoofer Array. The rigging
attachment positions on the adapter grid and enclosures allow for the the combination array to be splayed or tilted to obtain the desired
sound coverage. The adapter grid allows for 2 options -
1. Flying XLE Arrays below X-Line Very Compact Subwoofers, using the XLD Grid.
2. Stack XLE Arrays above X-Line Very Compact Subwoofers, using the XGS-4 Groundstack.
When using the Adapter Grid never exceed the rigging rating of any of the systems used with it or below it. These
ratings account for stresses resulting from the load angles encountered in curved arrays. These ratings are the limiting
factors. Consult the XLVC Rigging manuals, and/or the rigging label on the XLVC systems for the ratings when used in
curved arrays. The Adapter Grid has been designed to exceed the structural ratings for the XLVC loudspeaker sys-
tems, so if the structural ratings are not exceeded for loudspeaker system within the column, the structural rating for the
Adapter Grid will not be exceeded.
Figure 1: Using the AGSE for Flying Arrays Figure 2: Using the AGSE for Groundstacking
XLD Grid
XLVC
Subwoofer
XLVC-BGK
Bottom Grid Kit
(Set of 2 Hinge
Bars and Swing
Arms along with
8 Pins)
AGSE
Adapter Grid
XLE Series
Loudspeaker
XLVC
Subwoofer
XLVC-BGK
Bottom Grid Kit
(Set of 2 Hinge
Bars and Swing
Arms along with
8 Pins)
AGSE
Adapter Grid
XLE Series
Loudspeaker
XGS-4
Groundstack
Note: XLVC-BGK
Sold Separately
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Bosch Communications Systems 01/2008
Part Number LIT000152 Rev A
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
Electro-Voice
®
These configurations are showing the maximum number of enclosures allowed, based on the measured maximum
working loads of the rigging systems. They also show the proper balance for safety and acoustical performance. Oth-
er configurations are allowed at customer’s discretion without exceeding the maximum loads and angles of the systems
in use. For all configurations approaching these maximums, and all configurations used outdoors, use the following -
For Flying Configurations – In outdoor venues when wind is present, to prevent the system from shifting or twisting
with the wind, use a secondary rigging or anchoring point to pullback or lockdown the array. Please use an XLE GRID
and an XLVC-BGK bottom grid kit and follow instructions found on XLVC-BGK.
For Groundstack Configurations - In outdoor venues when wind is present, to prevent the system from shifting or twist-
ing with the wind, use the lag bolt holes in the base of the L-extrusions to secure the groundstack base to the mating
surface.
Figure 3: Sample Flying Array Using the
AGSE Adapter Grid
Figure 4: Sample Groundstack Array Using
the AGSE Adapter Grid
XLD Grid
XLVC
Subwoofers
(Maximum of 2)
XLVC-BGK
Bottom Grid Kit
(Set of 2 Hinge
Bars and Swing
Arms along with
8 Pins)
AGSE
Adapter Grid
XLE Series
Loudspeakers
(Potential Maximum
of 12, Depending on
Array Configuration)
XLVC
Subwoofer
(Maximum of 1)
XLVC-BGK
Bottom Grid Kit
(Set of 2 Hinge
Bars and Swing
Arms along with
8 Pins)
AGSE
Adapter
Grid
XGS-4
Groundstack
Note: XLVC-BGK
Sold Separately
XLE Series
Loudspeakers
(Maximum of 7)
Note: Figures
3 and 4 not to
scale with each
other.
  • Page 1 1
  • Page 2 2

Electro-Voice AGSE Adaptor Grid Operating instructions

Electro-Voice
Brand
Electro-Voice
Model
AGSE Adaptor Grid
Category
Soundbar speakers
Type
Operating instructions
This manual is also suitable for

Electro-Voice AGSE Adaptor Grid allows for the integration of an XLE Array with an X-Line Very Compact Subwoofer Array. The rigging attachment positions on the adapter grid and enclosures allow for the the combination array to be splayed or tilted to obtain the desired sound coverage. The adapter grid allows for 2 options:

  1. Flying XLE Arrays below X-Line Very Compact Subwoofers, using the XLD Grid.
  2. Stack XLE Arrays above X-Line Very Compact Subwoofers, using the XGS-4 Groundstack.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents