Bosch HBN 5405.0 A Installation guide

Brand: Bosch

Model: HBN 5405.0 A

Category: Cookers

Type: Installation guide

This manual is also suitable for

BOSCH

INSTALLATION INSTRUCTION' MANUAL

for

Bosch Electric Built-in

Single & Double Oven Models HBN 64.J65,.166.,

BEFORE YOU BEGIN, READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY

IMPORTANT: Save these instructions for _e local electrical inspector's nse'_

INSTALLER: Please leave this manual w_th owner for future reference. |

OWNER: Please keep this manual for future reference /

Table of Contents

INTRODUCTION .............................................................................................................................

Tools You Will Need ...................................................................................................................

Power Requirements ............. .........

Choosing Oven Location .............................................................................................................

Steps for Installation ....................................................................................................................

TECHNICAL DATA .................................................................................................................... [....

Single oven ...................................................................................................................................

Double oven ..................................................................................................................................

UNDERCOUNTER INSTALLATION ..........................................................................................

SINGLE OVEN ............................................................................................................................

WALL INSTALLATION .................................................................................. ...............................

SINGLE OVEN ............................................................................................................................

DOUBLE OVEN ......................................................................................... .................................

.i A . . ........... ,. ,.°,***°°,,(ELECTRIC L SUPPLY ......

WIRING REQUIREMENTS ......................................................................................................

CONNECTING TO 208 VOLT CIRCUIT ............................. :.................................................

ELECTRICAL CONNECTIONS .................................................................

3-WIRE BRANCH CIRCUIT ..............................

4-WIRE BRANCH CIRCUIT .....................................................................................................

FINAL CHECKLIST ........................................................................................................................

INTRODUCTION

Please read these instructions COMPLETELY

AND CAREFULLY. They will save you time .and

effort and help to ensure optimum oven perform-

mace. Be sure to observe all WARNINGS.

These installation instructions are int_ndad for

• use by a qualified installer. In addition to these in-

structions the oven shall be installed:

• In the United States, in accordance with the Na-

tional Electric Code/State and Municipal codes

and/or local codes.

• In Canada, in accordance with Canadian Elec-

tric Code C22.1-1ateSt edition/Provincial and

Municipal codes and/or local codes.

The,_ shall be carefully followed at all times.

Note: If installing your oven in Canada please

check tO make sure that you have a model

with the UL Canadian listing mark, as

shown below:

The UL Canadian listing mark consists of the cir-

cled UL symbol preceded by the letter "C", as

showm This should appear on the oven's rating

plate along with the UL United States listing

mark, which is the circled UL symbol above but

not preceded by the letter "C".

TOOLS YOU WILL NEED

The following tools "areneeded to install your new

oven:

• Tape measure and straightedge or ruler

• Pencil

• Phillips screwdriver

• Level

• Wire cutters and wire stripper

• I" hole saw

• Hand or saber saw.

POWER REQUIREMENTS

The oven must be supplied with the proper volt-

age and frequency. The oven is manufactured to

be connected to a three wire or four wire, single

phase, 240 volt, 60 Hz AC electrical supply on a

separate, circuit fused on both sides of the line. If

•,aT208 volt circuit must be used, wiring inside the

oven must be modified. See Connection to a 208

Volt Circuit, in this manuai. A circui[ breaker or

time-delay fuse sized not to exceed the circuit rat-

ing of the appliance specified on the rating plate

located on the frame behind the door of the oven

is recommended.

The oven must be supplied with copper wires

ONLY.

It is recommended that you have the electrical

wiring and hook-up of your oven performed by a

qualified elcc_iciam After installation is com-

flete have the electrician show you where the

main disconnect is and which of the circuit break-

ers/fuses are for the oven.

CHOOSING OVEN LOCATION

Carefully select the location where the oven will

be placed. The oven should be located for conven-

ient use in the kitchen, but away from strong

drafts. Strong drafts may be caused by open doors

or windows, or by heating and/or air conditioning

vents or fans. Make sure that electrical power can

be provided to the location selected.

STEPS FOR INSTALLATION .'

The following pages provide the necessary infor-

mation for proper installation of the oven ar-

ranged as follows:

• Technical Data

• Installation Cutout Dimensions, Required

Clearances and Mounting instructions for:

> Undercounter Installation, Single Oven

>Wall Installation, Single Oven

>Wall Installation, Double Oven

• Electrical Supply and Wiring Requirements

• Modifications required if Connecting to 208

Volt Circuit.

• Electrical Connections for 3-wire or 4-wire

B'ranch Circuit.

• Final Checklist.

TECHNICAL DATA

SINGLE OVEN

For cutout dimensions see following sections titled:

Preparing Location

Single Oven

Models

HBN 642A UC

HBN 645A UC

HBN 646A UC

Electrical Ratings

and Maximum Connected Load

Volts Hertz Amperes

@240V/208V

240/208 60 13.1/13.3

2401208 60 13.1/13.3

Watts

@240V/208V

3,150/2,775

Convection

Oven

Yes

DOUBLE OVEN

For cutout dimensions sec following sections titled:

Preparing Location

Double Oven

Models

HBN 652A UC

HBN 655A UC

[-IBN 656A UC

HBN 662A UC

HBN 665A UC

HBN 666A UC

Electrical Ratings

and Maximum Connected Load

Volts Hertz Amperes

@240V/208V

2401208 60 26.3/24.8

240/208 60 26.3/24.8

Watts

@240V/208V

6,300/5,150

Convection

Oven

(_p_ot_m)

Yes/No

Yes/Yes

UNDERCOUNTER INSTALLATION, SINGLE

-- m

O_n elec_l_ supply:

LocateJun_onboxIn

_lJa_mt cabinetorbelow

bottomsupportsurface.

_" openingwidth

Bottom supper sud_,e must

be solid,le_i_and able to

supper at leastof150 Ibs.

toe spa_ anm

2e.._" ._flh of oven do_- frame

114"min. distance

b_'ween ovln door

frmemd-,,'jas*nt

_ doom or dmw_ fron'=

F--

maintain minimum spadng u ahown.

Secure oven to cabinet using 1he

prodded, Screws shouldbe _ _lrOUgh

rnoun_g holes In 1he_ Indicted |n I_

frame (o-r_mdoor to ase frame and mounting

bolas). Do notove_ghten sa_ws.

Note: Decorsthteinsertsmust

maintain minimum spacing as shown.

Refer to and follow Notes and Warning listed under Wall Installation, Single Oven (facing page)

WALL INSTALLATION, SINGLE OVEN

Secureoven tocabinet uSklgthe screws

movlded. Screws should be Inserted

.= Ihrough the mountln_ holes In _e

posi_ora _ldicat_d in me frame (o_m

! doorto see flame andmounlJngho_esI.

Donotov_tighten screws.

Nnte:

Do not slide oven across floor. Dam-

age to floor covering or floor could re-

sult.

The oven support surface must be a

minimum 3/4" thick plywood plat-

form, solid, level and flush with the

bottom of the cabinet cutout.

Use extreme caution when moving or

installing the oven. It is very heavy.

Be very careful when moving or in-

stalling the oven to avoid damage to

the oven frame or damage to the cabi-

nets.

Be sure to level oven. An oven that is

not level may provide poor or incon-

sistent baking results.

6. Be careful when placing oven. DO

NOT pinch the conduit between the

oven back or wall and the inner cabi-

net wall or floor.

Securely fasten oven to cabinet using the

screws provided. Failure to do so could result

in oven moving or tipping during use and

causing damage to the oven or cabinets or per-

sonal injury.

WALL INSTALLATION, DOUBLE OVEN

Secure oven to cabinet using the screws

provided. Screws should be inserted

through the mounting holes in the

positions indicated in the frame (open

door to see frame and mounting holes).

Do notovertightan screws,

Note:

Do not slide oven across floor. Dam-

age to floor covering or floor could re-

sult.

The oven support surface must be a

minimum 3/4" thick plywood plat-

form, solid, level and flush with the

bottom of the cabinet cutout.

3. Use extreme caution when moving or

installing the oven. It is very heavy.

4. Be very careful when moving or in-,

stalling the oven to avoid damage to

the oven frame or damage to the cabi-

nets.

Be sure to level oven. An oven that is

not level may provide poor or incon-

sistent baking results.

6. Be careful when' placing oven. DO

NOT pinch the conduit between the

oven back or wail and the inner cabi-

net wall or floor.

Securely fasten oven to cabinet using the

screws provided. Failure to do so could result

in oven moving or tipping during use and

causing damage to the oven or cabinets or per-

sonal injury.

ELECTRICAL SUPPLY

Before installing the oven have a qualified electri-

cian verify that your home is provided with ade-

quate electrical service and that the addition of

the oven will not overload the branch circuit on

which it is to be installed. A separate three-wire

or four-wire single phase, 240 Volt, 60 Hz., or a

208 Volt, 60 Hz. branch circuit is required.

Note: For use with 208 V, 60 Hz supply voltage

the wiring must be modified as shown in

Connecting to 208 Volt Circuit.

For hook-up of the oven you will need to have an

approved junction box installed where it will be

easily reached through the front of the cabinet

where the oven will be located. The oven has 3

feet of conduit. Allow two to three feet of slack in

the line so that the oven can be moved if servicing

is ever necessary. DO NOT shorten the flexible

conduit.

ELECTRICALSHOCKHAZARD

• The electrical power to the oven branch cir-

cuit must be shut off while line connections

are being made.

• Do not use an extension cord with this ap-

pliance.

• Electrical ground is required on this appli-

ance. The free end of the green wire (the

ground wire) must be connected to a suit-

able ground.

This wire must remain grounded to the

oven.

• If cold water pipe is interrupted by plastic,

non-metallic gaskets, union connections or

other insulating materials, DO NOT use for

grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the NEUTRAL or

GROUNDING circuit. A fuse in the NEU-

TRAL or GROUNDING circuit could result

in an electrical shock.

• Check with a qualified electrician if you are

in doubt as to whether the appliance is

properly grounded.

Failure to follow these instructions could re-

sult in serious injury or death.

WIRING REQUIREMENTS

When making the wire connections, use the entire

length of the conduit provided (3 fee0. The con-

duit must not be cut.

Before making connections make sure the power

is off and read and observe the following:

1. A. separate three-wire or four wire, single

phase, 240 Volt, 60 Hz. or 208 Volt, 60 Hz

branch circuit is required for the oven.

The oven must be connected with COPPER

WIRE ONLY.

In the United States:

Wiring must conform to the National Electri-

cal Code, ANSI/NFPA No. 70 latest edition.

You can obtain a copy of the National Elec-

trical Code by writing:

National Fife Protection Association

Batterymarch Park ..

Quincy, MA 02269

In Canada:

W'tring must conform to Canadian Electrical

Code C22.1- latest edition. You can obtain

copies of the Canadian Electrical Code by

writing:

Canadian Standards Association

178 Rexdale Boulevard

Rexdale (Toronto), Ontario, Canada

M9W 1R3

Wire size (COPPER WIRE ONLY) and con-

nections must be suitable for the rating of the

appliance per the National Electrical Code

requirements. The flexible armored cable ex-

tending from the oven should be connected

directly to the junction box.

The junction box should be located so as to

allow as much slack as possible between the

junction box and the oven so it can be moved

if servicing is ever required.

A U.L. listed conduit connector must be pro-

vided at each end oftbe power supply cable.

CONNECTING TO 208 V CIRCUIT

The ovens are pre-wired for connection to 240

volt, 60 Hertz supply. If connecting to a 208 volt,

60 Hz. supply a jumper must be used across, two

terminals. For the double oven models ther'e are

two jumpers, one for the upper oven and one for

the lower oven. For the single ovens there is one

jumper.

Please refer to figures below for placement of

jumper for 208 volt, 60 hertz connection.

To connect to 208 volt circuit:

1 Remove the access panel(s) lQcated on the

back of the oven(s).

Loosen the first and second screws in the ter-

minal block as shown in applicable figure

above.

Place the metal jumper between the first

and second screws and tighten screws to

hold jumper in place.

4. Replace access panel(s).

Placing ofjumper for single oven

or upper oven of double oven,

for connection to 208 volt, 60 Hz.

B_om

Jumper

JL_nper

After

Placing of jumper for lower oven

of double oven, for connection to

208 volt, 60 Hz.

Before

Jumper

After

ELECTRICAL CONNECTIONS

This appliances is manufactured with a green

GROUND wire connected to the oven chassis.

After making sure that the power has been turned

off connect the flexible conduit from the oven to

the junction box using a U.L. listed conduit con-

nector. Figures A and B and the instructions pro-

vided below present the most common way of

connecting the ovens. Your local codes and ordi-

nances, of course, take precedence to these in-

structions. Complete electrical connections ac-

cording to local codes and ordinances.

3-WIRE BRANCH CIRCUIT

Refer to Figure A, where local codes allow the

connection of GROUND wire from the oven to

the branch circuit NEUTRAL wire (grey or white

colored wire):

• If local codes permit, connect the green

GROUND wire from the oven and the white

wire from the oven to the branch circuit NEU-

TRAL wire (grey or white colored wire).

• Connect the red and black leads from the cook-

top to the corresponding leads in the junction .

box.

,klncSon I_x allb_ from

Redwlr_,_ _ Grounded Neut_l

B _

_ U.L-kded €ondtdt connector

Immo,_m

Figure A.

4-WIRE BRANCH CIRCUIT

Refer to Figure B:

• Connect the green GROUND wire from the

oven to the GROUND wire in the junction box

(bare or green colored wire).

". Connect the red and black leads from the oven

to the corresponding leads in the junction box.

• Connect the white wire from the oven to the

NEUTRAL (grey or white) wire in the junction

box.

_Ungrounded Neutral

Cable

from oven

Black wlr_

U.L-_ed conduit connector

Figure B.

FINAL CHECK LIST

To prevent improper connections leading to dam-

age of electrical components and so voiding the

warranty, the following steps must be performed:

Check the electrical requirements and make

sure you have the correct elec_ical supply

and that the oven is properly grounded.

Make sure all control knobs are in the off po-

sition.

Turn on the power supply to the oven. When

the oven is first turned on the display will

come on showing all the call-outs and then

will become blank with the Set Clock sym-

bol in the upper fight corner, as shown be-

low.

SET

Check power at the jtmetion box wires using

a volt meter having a range of 0-250 VAC. If

you have installed the oven for use on 240

volt supply you should find that the voltage

reading between the black and red wires

(Line to Line) should be 220 to 240 volts. If

you have modified the oven(s) for use on 208

volt the voltage reading between the black

and red wires should be 190 to 208 volts.

Set the time of day by pressing the Set

Clock button and pressing the plus (+) or mi-

nus (-) button, to the right of the display to

set the correct time. Once the time is set de-

press the Set Clock button to enter the time.

A "beep" will sound and the Set Clock sym-

bol in the upper right wiU disappear.

Turn the Mode Selector knob to Manual po-

sition, the Selector knob to Bake and turn the

Temperature knob to 350 *F. The cooling

fan, the oven lights and the heat light should

come on to indicate that the oven is heating.

The heat light will turn off when the set tem-

perature (350 *F),is reached. Turn Tempera-

ture knob to off. If you have installed a dou-

ble oven repeat test for second oven.

To check the other oven functions refer to

the Using the Oven Controls section of the

Use and Care Manual.

8. If the oven is working properly turn the Se-

lector knob(s) and the Temperature Control

knob(s) to their off positions and press in the

knobs so that they are flush with the oven

and turn off the power supply to the oven.

9. Place the cover on the junction box and

make sure the cover is securely fastened and

turn on the power to the oven.

10. Leave these INSTALLATION instructions

as well as the USE AND CARE MANUAL

with the owner.

Bosch HBN 5405.0 A Installation guide

Brand: Bosch

Model: HBN 5405.0 A

Category: Cookers

Type: Installation guide

This manual is also suitable for

Download PDF

report

Bosch HBN 5405.0 A Installation guide

This manual is also suitable for

Bosch HBN 5405.0 A Installation guide

Related papers

Other documents