In-Sink-Erator SS-100-1 User manual

PARTS LIST FOR COMMERCIAL DISPOSERS MODEL

SS-100 IN-SINK-ERATOR

®

1 H.P.

(Includes Models SS-100-L, SS-100-2, SS-100-3)

ORDER BY PART NUMBER, NOT CODE NUMBER

(Minimum Parts Order $3.00)

(ALL PARTS F.O.B.FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)

EFFECTIVE March, 1972

PARTS LIST FOR COMMERCIAL DISPOSERS

MODEL SS-100. IN-SINK-ERATOR

®

1 H.P.

(Includes Models SS-100-1, SS-100-2, SS-100-3)

Code

No.

Part

No.

Reqd

.

Description

1 11004 1 Mounting Flange

2 11016 1 Gasket, Mounting

3 11020-A 1 Body, Container

4 1491 6 Bolt, Mounting

5 11227 1 Pipe Plug

6 11006 1 Seal, Body-Shredder

7 12442 1 Body and Cover Assembly

8 11252-A 1 Stationary Shredder

9 11260 1 Nut, Shredder

10 12445 1 Washer

11 12142 1 Washer, Fibre

12 12316 I Rotor Shredder

13 12327 1 Upper End Bell- Includes

Codes 14-16-17-18

14 12321 1 Face Seal

15 12318 1 Spacer Sleeve

16 12319 1 Centrifugal Moisture Shield

17 12610 1 Bearing Assembly - Upper

18 12326 1 Oil and Water Retainer

19 11322 2 Woodruff Key

20 12611

Bearing - Seal Key Includes

Codes 9-10-11.14-15-16-17-18-19

21 11444 3 Washer

22 1491 3 Bolt

23 1470 1 Washer, Tail Pipe

24 5487 1 Tail Pipe

25 1461 1 Flange - Tail Pipe

26 1468 2 Bolt - Tail Pipe

27 12330-B

Rotor & Shaft Assembly (Includes

Codes 29 & 30)

208 Volt, 60 Cycle, Single Phase S,

115/230 Volt, 60 Cycle, Single Phase

28 1233I-B

Rotor & Shaft Assembly

208 Volt, 60 Cycle, Three Phase &

230/460 Volt, 60 Cycle, Three Phase

29 1537 2 Spring - Centrifugal Switch

30 12348 1 Centrifugal Switch

31 7422 2 Screw

32 12393 1 Start Switch

Code

No.

Part

No.

Re

q

d

Description

33 5765 2 Screw

34 12370 1 Shell - Trim

35 12351-G 1 Stator Assembly

208 Volt, 60 Cycle, Single Phase

36 12351-B 1 Stator Assembly

115/230 Volt, 60 Cycle, Single Phase

37 12549-8 1 Siator Assembly

208 Volt, 60 Cycle, Three Phase

38 12352-8 1 Stator Assembly

230/460 Volt, 60 Cycle, Three Phase

39 12433 1 Terminal Box Mounting Bracket -

Single Phase

40 12433-E 1 Terminal Box Mounting Bracket -

Three Phase

41 11448 4 Screw

42 12384 1 Bushing

43 11868 1 Capacitor - Single Phase Only

44 12389 1 Overload Protector

208 Volt, 60 Cycle, Single Phase

115/230 Volt, 60 Cycle, Single Phase

45 12391 1 Overload Protector

208 Volt, 60 Cycle, Three Phase &

230/460 Volt, 60 Cycle, Three Phase

46 12378 1 Clamp, Overload

47 5765 2 Screw

48 12372 1 Terminal Box

49 12383 1 Grommet

50 12381 1 Screw

51 12415 1 Bearing - Lower

52 12399 1 Spring, Pre-load

53 12684 1 End Frame, Lower

54 12395 1 Fan

55 12635 I Retaining Ring

56 12490 3 Tube, Spacer

57 11940 3 Bolt, Thru

58 12396 1 Cover, Bottom

59 12586 2 Plug

60 11757-B 2 Leg (Optional)

61 12564 1 Ground Screw

ORDER BY PART NUMBER, NOT CODE NUMBER

(Minimum Parts Order $3.00)

(AIL PARTS F.O.B. FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)

Form No. C-I24-72C PRINTED IN U.S.A.

IN

-

SINK

-

E

BATOR DIVISION

EMERSON ELECTRIC CO.

4700-21ST STREET RACINE.

WISCONSIN S3406 PHONE:

(414) 637-6761

ORDER BY PART NUMBER, HOT CODE NUMBER

(All Part F.O.B. Agency/Dept) (Include Serial and Model Number of Disposer when ordering)

COMMERCIAL DISPOSER

CANADIAN

MODEL MODEL

SS-100-8 115/230/60/1 SS-100-12

SS-100-9 208/60/1 SS-100-13

SS-100-10 230/460/60/3 SS-100-14

SS-100-11 208/60/3 SS-100-15

Start with Serial #70.000

ISE

IN-SINK-ERATOR

September, 1979

1

H.P.

CANADIAN

MODEL MODEL

SS

-

100

-

8 115/230/60/1

SS

-

100

-

12

SS-100-9 208/60/1 SS-100-13

SS-100-10 230/460/60/3 SS-100-14

SS-100-11 208/60/3 SS-100-15

Code

No.

Port

No.

Req.

Description Code No.

Part

No.

Req.

Description

1 11004

1

Mounting Flange 36 130754 1 Stator Assembly

2 11016

1

Gasket, Mounting

115/230 Volt, 60 Hz, Single Phase

3 11020-A

1

Body. Container 37 13075-0 1 Stator Assembly

4 1491 6 Bolt, Mounting

208 Volt, 60 Hz, Single Phase

5 11227

1

Pipe Plug 38 13077-C 1 Stator Assembly

6 11006

1

Seal. Body-Shredder

230/460 Volt, 60 Hz, Three Phase

7 12443

1

Body and Cover Assembly 39 13076-8 I Stator Assembly

8 11252-A

1

Stationary Shredder

208 Volt, 60 Hz. Three Phase

9 11260

1

Nut. Shredder 40 13433 1 Terminal Box Mounting Bracket

10 12445

1

Washer

Single Phase

11 0143 1 Washer, Fibre 41 1243 3-E 1 Terminal Box Mounting Bracket

12 13944

1

Rotor Shredder

Three Phase

13 13081

1

End Bell, Upper Includes Codes 42 11448 4 Screw

14 thru 21 43 12384 1 Bushing

14 12936 1 Shield 44 11868 1 Capacitor (Single Phase only)

15 13137 6 Screw 45 12389 1 Overload Protector

16 12934-A 1 Seal Assembly 208 Volt. 60 Hz. Single Phase

17 12935

1

Sleeve Spacer

115/230 Volt, 60 Hz, Single Phase

18 13860

1

0'Ring 46 12391 1 Overload Protector

19 12319

1

Centrifugal Moisture Shield

208 Volt, 60 Hz. Three Phase

20 12610 1 Bearing Assembly - Upper 230/460 Volt, 60 Hz, Three Phase

21 13326 1 Oil and Watt Retains 47 12378 1 Clamp. Overload

22 11322 3 Woodruff Key 48 5765 2 Screw

23 13080 1 Bearing Seal Kit, Includes Codes 9, 10 49 12372 1 Terminal Box

11, 14, 15, 16, 17, 18, 19, 20, 21, 22 50 12383 1 Grommet

24 11444 3 Washer 51 12381 1 Screw

25 1491 3 Bolt 52 1241$ 1 Bearing, Lower

26 1470 1 Washer Tail Pipe 53 12399 1 Spring, Pre-load

27 5487 1 Toil Pipe 54 12684 1 End Frame, lower

28 1461 1 Range - Tail Pipe 55 123955 1 Fan

29 1460 2 Bolt - Tail Pipe 56 12635 1 Retaining Ring

30 12947-B 1 Rotor & Shaft Assembly 57 12490 3 Tube, Spacer

Includes Code #31 58 11940 3 Bolt, Thru

206 Volt, 60 Hz, Single Phase & 59 12396 1 Cover, Bottom

115/230 Volt, 60 Hz, Single Phone 60 12564 1 Ground Screw

31 12954 1 Centrifugal Switch Assembly 61 11757-B 2 Leg (Optional)

32 12948-B 1 Rotor & Shaft Assembly

208 Volt. 60 Hi, Three Phase

CANADIAN ONLY

230/460, 60 Hi, Three Phase 62 12928 1 Overload Protector

33 7433 2 Screw

115/230 Volt, 60 Hz. Single Phase

34 13393 1 Start Switch 63 11930 1 Overload Protector

35 12370 1 Shell - Trim 208 Volt, 60 Hz, Single Phase

ORDER BY PART NUMBER. MOT CODE NUMBER

(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)

I

SE

IN SINK ERATOR

PRINTED IN USA

4173

JAM RELEASE BAR

11009

SPLASH BAFFLE

1124

SLEEVE GUARD

IN

-

SINK

-

ERATOR DIVISION

EMERSON ELECTRIC CO.

4700-21 ST STREET

RACINE. WISCONSIN 53406

PHONE: (414) 554-5432

IN

SINK

ERATOR

COMMERCIAL DISPOSER

MODEL No. SS100-16

(100 / 208 / Volt / 50/SOHz / 1 Phase) 1 H.P.

Start Date:

3/99

Engineer Number:

13025N

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

PART

NO.

CODE

PART

NO.

NO. NO. REQ. DESCRIPTION NO. NO. REQ. DESCRIPTION

1

11004

1

Flange, Mounting

30

12947B

1

Rotor & Shaft Assembly

2 11016 1 Gasket, Mounting (Includes Codes 31 & 47 )

3 11020A 1 Body Upper Assy 31 12954 1 Centrifugal Actuator

4 1491 6 Screw (1/4-20 x 3/4) 32 8221 2 Screw (8-32 x 1/2)

5 11227 1 Plug, Pipe 33 12393 1 Switch, Start

6 11006 1 Gasket, Shredder 34 12370 1 Trim Band

7 12442 1 Body & Cover Assy 35 1836A 2 Screw (8-32 x 1/2)

8 11252A 1 Shredder, Stationary 36 13075E 1 Stator Assy

9 11260 1 Nut 37 12433 1 Bracket Assy (Mounting)

10 12445 1 Washer 38 11448 4 Screw (8-18 x 1/4)

11 12142 1 Washer, Fiber 39 12384 1 Bushing

12 12944 1 Rotor Shredder Assy 40 11868 1 Capacitor

13 13081 1 Upper End Bell Assy 41 13422L 1 Overload Protector

(Includes Codes 14-22) 42 12378 1 Clamp, Overload

14 12936 1 Shield 43 8221 2 Screw (8-32 x 1/2)

15 1269 6 Screw (8-18 x 1/2) 44 13396 1 Box, Terminal Assy

16 12934A 1 Seal Assy (Includes Code 40)

17 12935 1 Sleeve, Spacer 45 12381 1 Screw (8-32 x 1-1/4)

18 12860 1 0-Ring 46 12383 1 Grommet, Overload

19 12319 1 Slinger 47 12415 1 Bearing, Lower

20 12610 1 Upper Bearing Assy 48 12399 1 Spring, Pre-load

21 12326 1 Water & Oil Seal 49 12684 1 End Frame, Lower

22 11322 3 Key. Woodruff 50 12395 1 Fan

23 13080 1 Kit, Bearing Seal 51 12635 1 Ring, Retaining

(Includes Codes 9-11 & 14-22) 52 12490 3 Tube, Spacer

24 11444 3 Washer, Lock 53 11940A 1 Bolt, Thru

25 3135 3 Screw (1/4-20x1) 54 12396 1 Cover, Bottom

26 1470 1 Gasket, Tailpipe 55 2466A 1 Screw, Ground

27 8219 1 Tailpipe 56 11757B 2 Tube, Foot Assembly

28 1461 1 Flange, Tailipe (Optional)

29 1468 2 Screw (1/4-20x1/2)

ORDER BY PART NUMBER, NOT CODE NUMBER

(All Pans F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)

ISE

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL

SS-100-18 115/208/230/60/1

SS-100-19 208/230/460/60/3

May.

1985

1

H.P.

IN

-

SINK

-

ERATOR

COMMERCIAL

DISPOSER

MODEL NO. SS100-20

CANADIAN (115/208-30/60/10)

Start Date:

7/87

Engineer Number

130858

0RDER BY PART NUMBER, NOTCODE NUMBER

CODE

PART

NO.

DESCRIPTION

CODE

PART

NO.

DESCRIPTION

NO. NO. REQ.

1

11004

1

Flange, Mounting

31

12954

1

Centrifugal Actuator

2 11016

1

Gasket, Mounting

(Single Phase Only)

3 11020-A

1

Body Assy, Upper 32 8221 2 Screw

4 1491 6 Screw, Mounting 33 12393 1 Switch, Start

5 11227 1 Pipe Plug (Single Phase Only)

6 11006

1

Gasket, Shredder 34 12370 1 Trim, Band

7 12442

1

Body & Cover Assy 35 1836-A 2 Screw

8 11252-A

1

Shredder, Stationary 36 13075-E 1 Stator Assy

9 11260

1

Nut

(Single Phase)

10 12445

1

Washer 37 12433 1 Bracket Assy

11 12142

1

Washer, Fiber

(Mounting) (Single Phase)

12 12944

1

Shredder Assy, Rotor 38 11448 4 Screw

13 13081

1

End Bell Assy, Upper 39 12384 1 Bushing

(Incl. Codes 14 thru 22) 40 11868 1 Capacitor

14 12936 1 Shield

(Single Phase Only)

15 1269 6 Screw, Tapping 41 13422-L 1 Overload, Protector

16 12934-A 1 Seal Assy (Single Phase)

17 12935 1 Sleeve, Spacer 42 12378 1 Clamp, Overload

18 12860 1 0-Ring 43 5765 2 Screw, Tapping

19 12319 1 Slinger 44 12372 1 Box, Terminal

20 12610 1 Bearing Assy, Upper 45 12381 1 Screw

21 12326 1 Seal, Water & Oil 46 12383 1 Grommet, Overload

22 11322 3 Key, Woodruff 47 12415 1 Bearing, Lower

23 13080 1 Bearing Seal Kit 48 12399 1 Washer, Spring

(Incl. Codes 9-11 49 12684 1 End Frame, Lower

& 14 thru 22) 50 12395 1 Fan

24 1)444 3 Washer, Lock 51 12635 1 Ring, Retaining

25 3135 3 Screw 52 12490 3 Tube, Spacer

26 1470 1 Gasket, Tailpipe 53 11940-A 3 Bolt, Thru

27 5487 1 Tailpipe 54 12396 1 Cover, Bottom

28 1461 1 Flange, Tailpipe 55 2466-A 1 Screw, Ground

29 1468 2 Screw, Tailpipe 56 11757-B 2 Tube Assy, Foot

30 12947-B 1 Rotor & Shaft Assy

(Optional)

(Single Phase)

(Incl. Codes 31 & 47)

Start Date:

7/87

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-22

U.S.A.

(208-30/460/60/30)

Engineer Number

13385D

1 H.P.

ORDER BY PART NUMBER NOT

CODE

NO.

PART NO. NO. REQ. DESCRIPTION CODE NO.

PART NO. NO. REQ. DESCRIPTION

1

11004

1

Flange

, Mounting

29

1468

2

Screw, Tailpipe

2 11016

1

Gasket, Mounting 30 12948-B 1 Rotor & Shaft Assy

3 11020-A

1

Body Assy, Upper

(Three Phase)

4 1491 6 Screw, Mounting

(IncI Code 43)

5 11227

1

Pipe Plug 31 12370 1 Trim, Band

6 11006

1

Gasket, Shredder 32 1836-A 2 Screw

7 12442

1

Body & Cover Assy 33 13077-C 1 Stator Assy

8 11252-A

1

Shredder, Stationary

(Three Phase)

9 11260 1 Nut 34 12433-E 1 Bracket, Terminal Box

10 12445 1 Washer

(Three Phase)

11 12142 1 Washer, Fiber 35 11448 4 Screw

12 12944 1 Shredder Assy, Rotor 36 12384 1 Bushing

13 13081 1 End Bell Assy, Upper 37 13422-N 1 Overload, Protector

(IncI Codes 14 thru 22)

(Three Phase)

14 12936 1 Shield 38 12378 1 Clamp, Overload

15 1269 6 Screw, Tapping 39 5765 2 Screw, Tapping

16 12934-A 1 Seal Assy 40 12372 1 Box, Terminal

17 12935 1 Sleeve, Spacer 41 12381 1 Screw

18 12860 1 0-Ring 42 12383 1 Grommet, Overload

19 12319 1 Slinger 43 12415 1 Bearing, Lower

20 12610 1 Bearing Assy, Upper 44 12399 1 Washer, Spring

21 12326 1 Seal, Water & Oil 45 12684 1 End Frame, Lower

22 11322 3 Key, Woodruff 46 12395 1 Fan

23 13080 1 Bearing Seal Kit 47 12635 1 Ring, Retaining

(IncI Codes 9.11 48 12490 3 Tube, Spacer

& 14 thru 22) 49 11940-A 3 Bolt. Thru

24 11444 3 Washer, Lock 50 12396 1 Cover, Bottom

25 3135 3 Screw 51 2466-A 1 Screw, Ground

26 1470 1 Gasket, Tail pipe 52 11757-B 2 Tube Assy, Foot

27 5487 1 Tailpipe

(Optional)

28 1461 1 Flange, Tailpipe

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-23

CANADIAN

(208-230/460/60/30)

Start Date:

7/87

Engineer Number:

13385E

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO.

PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

1

11004

1

Flange, Mounting

29

1468

2

Screw, Tailpipe

2

11016

1

Gasket, Mounting

30

12948

-

B

1

Rotor

&

Shaft Assy

3

11020

-

A

1

Body Assy, Upper

(Three Phase)

4

1491

6

Screw, Mounting

(IncI. Code

43)

5

11227

1

Pipe Plug

31

12370

I

Trim, Band

6

11006

1

Gasket, Shredder

32

1836

-

A

2

Screw

7

12442

1

Body

&

Cover Assy

33

13077

-

C

1

Stator Assy

8

11252

-

A

1

Shredder, Stationary

(Three Phase)

9

11260

1

Nut

34

12433

-

E

1

Bracket, Terminal Box

10

12445

1

Washer

(Three Phase)

11

12142

1

Washer,

Fiber

35

11448

4

Screw

12

12944

1

Shredder Assy, Rotor

36

12384

1

Bushing

13

13081

1

End Bell Assy, Upper

37

13422

-

N

1

Overload, Protector

(IncI. Codes

14

thru

22)

(Three Phase)

14

12936

1

Shield

38

12378

1

Clamp, Overload

15

1269

6

Screw

, Tapping

39

5765

2

Screw, Tapping

16

12934

-

A

1

Seal Assy

40

12372

1

Box, Terminal

17

12935

1

Sleeve, Spacer

41

12381

1

Screw

18

12860

1

0

-

Ring

42

12383

1

Grommet, Overload

19

12319

1

Slinger

43

12415

1

Bearing, lower

20

12610

1

Bearing Assy, Upper

44

12399

1

Washer, Spring

21

12326

1

Seal, Water

&

Oil

45

12684

1

End Frame, Lower

22

11322

3

Key, Woodruff

46

12395

1

Fan

23

13080

1

Bearing Seal Kit

47

12635

1

Ring, Retaining

(IncI. Codes

9

-

11

48

12490

3

Tube, Spacer

& 14

thru

22)

49

1194

0

-

A

3

Bolt, Thru

24

11444

3

Washer, Lock

50

12396

1

Cover, Bottom

25

3135

3

Screw

51

2466

-

A

1

Screw, Ground

26

1470

1

Gasket, Tailpipa

52

11757

-

B

2

Tube Assy, Foot

27

5487

1

Tailpipe

(Optional)

28

1461

1

Flange, Tailpipe

ISE

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-24

(115/208/230 Volt/60HZ/1 Phase) 1 H.P.

Start Date:

03/90

Engineer Number

13385-0

Rev. 4/96

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO.

PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

1

11004

1

Flange, Mounting

27

12954

1

Centrifugal Actuator

2 11016 1 Gasket, Mounting 28 8221 2 Screw (8-32x1/2)

3

11020-A

1

Body, Assy, Upper

29

12393

1

Switch, Start

4 1491 6 Screw (1/4-20x3/4) 30 12370 1 Trim Band

5

11227

1

Plug, Pipe

31

1836-A

2

Screw (8-32x1/2)

6 11006 1 Gasket, Shredder 32 13075-E 1 Stator Assy

7 12442 1 Assy, Body & Cover 33 12433 1 Bracket Assy

8

11252-A

1

Shredder, Stationary

(Mounting)

9 11260 1 Nut 34 11448 4 Screw (8-18x1/4)

10 12445 1 Washer 35 11868 1 Capacitor

11

12142

1

Washer, Fiber

36

12378

1

Clamp, Overload

12

13586

1

Assy, Rotor Shredder

37

5765

2

Screw (8-32x1/2)

13 13597 1 Assy, Upper End Bell 38 13396-E 1 Box, Terminal Assy

(Incl. Codes 14 - 22)

(Incl. code 41)

14 12936 1 Shield 39 12381 1 Screw (8-32x1-1/4)

15

1269

6

Screw (8-18x1/2)

40

13559

1

Grommet, Overload

16 12934-A 1 Assy, Seal 41 13422BB 1 Overload Protector

17

12935

1

Sleeve, Spacer

42

12384

1

Bushing

18 12860 1 0-Ring 43 2466-A 1 Screw, Ground

19 12319 1 Slinger 44 12415 1 Bearing, Lower

20 12610 1 Bearing Assy, Upper 45 12399 1 Spring, Pre Load

21

12326

1

Seal, Water & Oil

46

12684

1

End Frame, Lower

22

11322

3

Key, Woodruff

47

12395

1

Fan

23 13080 1 Kit, Bearing Seal (Incl. 48 12635 1 Ring, Retaining

codes 9-11 &14-22) 49 12490 3 Tube, Spacer

24

11444

3

Washer, Lock

50

11940-A

3

Bolt, Thru

25

3135

3

Screw (1/4-20x1)

51

12396

1

Cover, Bottom

26

13592

1

Rotor & Shaft A\ssy.

52

11757-B

2

Tube, Foot Assy.

(Incl. Codes 27 & 42)

(Optional)

ENVIROVAC

COMMERCIAL DISPOSER

MODEL NO. SS100-25

(208/230/460 Volt/60 Hz/3 Phase) 1 H.P.

Start Date:

08/90

Engineer Number

13385-H

Rev. 1/96

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

PART

NO.

DESCRIPTION

CODE

PART NO.

NO.

DESCRIPTION

1 11004 1 Flange, Mounting 25 3135 3 Screw (1/4-20x1)

2 11016 1 Gasket, Mounting 26 13592-A 1 Rotor & Shaft Assy.

3 11020-A 1 Body, Assy, Upper

(Ind. Codes 40)

4 1491 6 Screw (1/4-20x3/4) 27 12370 1 Trim Band

5 11227 1 Plug, Pipe 28 1836-A 2 Screw (8-32x1/2)

6 11006 1 Gasket, Shredder 29 13714-B 1 Stator Assy

7 12442 1 Assy, Body & Cover 30 12433-E 1 Bracket Assy (Mounting)

8 11252-A 1 Shredder, Stationary 31 11448 4 Screw (8-18x1/4)

9 11260 1 Nut 32 12378 1 Clamp, Overload

10

12445 1 Washer 33 8221 2 Screw (8-32x1/2)

11 12142 1 Washer Fiber 34 13396 1 Box, Terminal Assy

12

13586 1

Assy, Rotor Shredder

(Inc), code 36)

13

13566

1

^^Q7

-

A

1 Assy, Upper End Bell 35 12381 1 Screw (8-32x1-1/4)

(lncl.Codes14.22) 36 12383 1 Grommet, Overload

14 12936 1 Shield 37 13422BD 1 Overload Protector

15 1269 6 Screw (8-18x1/2) 38 12384 1 Bushing

16 12934-A 1 Assy, Seal 39 2466-A 1 Screw, Ground

17 12935 1 Sleeve, Spacer 40 13709 1 Bearing, Lower

18 12860 1 0-Ring 41 13678 1 Spring, Pre-load

19 12319 1 Slinger 42 12684 1 End Frame, Lower

20 12610 1 Assy, Upper Bearing 43 12395 1 Fan

21 12326 1 Seal, Water & Oil 44 13677 1 Ring, Retaining

22 11322 3 Key, Woodruff 45 12490 3 Tube, Spacer

23 13080 1 Kit, Bearing Seal 46 12396 1 Cover, Bottom

(lncl. codes9-11&14-22) 47 11940-A 3 Bolt, Thru

24 11444 3 Washer, Lock 48 11757-B 2

Tube, Foot Assy.

(Optional)

ISE

IN-SINK-ERATOR

COMMERCIAL DINPOSEDR

MODEL NO. SS100-28

(115/208/230 Volt / 60Hz /1 Phase)

09/09/92

Engineer Number:

13660

1H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO.

PART NO.

NO. REQ.

DESCRIPTION

CODE NO.

PART NO.

NO.

REQ.

DE

SCRIPTION

1

11004

1

Flange, Mounting

31

13708

1

Centrifugal Actuator

2 11016 1 Gasket, Mounting 32 8221 2 Screw (8-32x1/2)

3 11020-A 1 Body. Assy, Upper 33 13707 1 Switch, Start

4 1491 6 Screw (1/4-20x3/4) 34 12370 1 Trim Band

5 11227 1 Plug, Pipe 35 1836-A 2 Screw(8-32x1/2)

6 11006 1 Gasket, Shredder 36 13713-B 1 Stator Assy

7 12442 1 Assy, Body & Cover 37 12433 1 Bracket Assy

8 11252-A 1 Shredder, Stationary

(Mounting)

9 11260 1 Nut 38 11448 4 Screw (8-18x1/4)

10 12445 1 Washer 39 12384 1 Bushing

11 12142 1 Washer, Fiber 40 11868 1 Capacitor

12 12944 1 Assy, Rotor Shredder 41 13422-E 1 Overload Protector

13 13722 1 Assy, Upper End Bell 42 12378 1 Clamp, Overload

(lncl.Codes14-22) 43 8221 2 Screw (8-32x1/2)

14 12936 1 Shield 44 13396 1 Box, Terminal Assy

15 1269 6 Screw (8-18x1/2)

(Incl. code 46)

16 12934-A 1 Assy, Seal 45 12381 1 Screw (8-32X1-1/4)

17 12935 1 Sleeve,Spacer 46 12383 1 Grommet, Overload

18 12860 1 0-Ring 47 13709 1 Bearing,Lower

19 12319 1 Slinger 48 13678 1 Spring, Pre-load

20 12610 1 Assy, Upper Bearing 49 13710 1 End Frame, Lower

21 12326 1 Seal, Water & Oil 50 13676 1 Fan

22 11322 3 Key, Wood ruff 51 13677 1 Ring, Retaining

23 13080 1 Kit. Bearing Seal (Incl. 52 12490 3 Tube,Spacer

codes 9-11& 14-22) 53 11940-A 3 Bolt, Thru

24 11444 3 Washer, Lock ' 54 12396 1 Cover, Bottom

25 3135 3 Screw(1/4-20x1) 55 2466-A 1 Screw, Ground

26 1470 1 Gasket, Tailpipe 56 11757-B 2 Tube, Foot Assy.

27 5487 1 Tailpipe

(Optional)

28 1461 1 Flange, Tail pipe

29 1468 2 Screw (1/4-20x1/2)

30 13674-B 1 Rotor & Shaft Assy.

(Incl. Codes 31 & 47)

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

1

11004

1

Flange, Mounting

28

1461

1

Flange, Tailpipe

2 11016 1 Gasket, Mounting 29 1468 2 Screw (1/4-20x1/2)

3 11020-A 1 Body, Assy, Upper 30 13674-H 1 Rotor & Shaft Assy

4 1491 6 Screw (1/4-20x3/4)

(Incl. Code 43)

5 11227 1 Pipe, Plug 31 12370 1 Trim, Band

6 11006 1 Gasket, Shredder 32 1836-A 2 Screw (8-32x1/2)

7 12442 1 Body & Cover Assy 33 13714-B 1 Staler Assy

8 11252-A 1 Shredder, Stationary 34 12433-E 1 Bracket Assy

9 11260 1 Nut

(Mounting)

10 12445 1 Washer 35 11448 4 Screw (8-18x1/4)

11 12142 1 Washer, Fiber 36 12384 1 Bushing

12 12944 1 Shredder Assy, Rotor 37 13422-N 1 Overload, Protector

13 13722 1 End Bell Assy, Upper 38 12378 1 Clamp, Overload

(Incl. Codes 14 thru 22) 39 8221 2 Screw (8-32x1/2)

14 12936 1 Shield 40 13396 1 Box, Terminal

15 1269 6 Screw (8-18x1/2)

(Incl. code 42)

16 12934-A 1 Seal Assy 41 12381 1 Screw (8-32x1-1/4)

17 12935 1 Sleeve, Spacer 42 12383 1 Grommet, Overload

18 12860 1 0-Ring 43 13709 1 Bearing, Lower

19 12319 1 Slinger 44 13678 1 Spring, Pre-load

20 12610 1 Bearing Assy, Upper 45 13747 1 End Frame, Lower

21 12326 1 Seal, Waters Oil 46 13676 1 Fan

22 11322 3 Key, Woodruff 47 13677 1 Ring, Retaining

23 13080 1 Bearing Seal Kit (Incl. 48 12490 3 Tube, Spacer

codes

9

-

10

-

11 & 14

thru

22)

49 11940-A 3 Bolt, Thru-

24 11444 3 Washer, Lock 50 12396 1 Cover. Bottom

25 3135 3 Screw (1/4-20x1/2) 51 2466-A 1 Screw, Ground

26 1470 1 Gasket, Tailpipe 52 11757-B 2 Tube Assy, Foot

27 5487 1 Tailpipe (Optional)

ISE

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-29

(208/230/460Volt / 60H2 / 3 Phase)

Start Date:

09-01-92

Engineer Number:

13660

-

A

1

H.P.

Start Data:

02/26/93

ISE

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-30 (C.S.A.)

(115/208/230 Volt / 60Hz /1 Phase)

Engineer Number:

13660-B

1 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO.

PART NO. NO. REQ. DESCRIPTION

1

11004

1

Flange, Mounting

31

13708

1

Centrifugal Actuator

2 11016 1 Gasket, Mounting 32 8221 2 Screw (8-32x1/2)

3 11020-A 1 Body, Assy, Upper 33 13707 1 Switch, Start

4 1491 6 Screw (1/4-20x3/4) 34 12370 1 Trim Band

5 11227 1 Plug, Pipe 35 1836-A 2 Screw (8-32x1/2)

6 11006 1 Gasket, Shredder 36 13713-B 1 Stator Assy

7 12442 1 Assy, Body & Cover 37 12433 1 Bracket Assy

8 11252-A 1 Shredder, Stationary

(Mounting)

9 11260 1 Nut 38 11448 4 Screw (8-18x1/4)

10 12445 1 Washer 39 12384 1 Bushing

11 12142 1 Washer, Fiber 40 11868 1 Capacitor

12 12944 1 Assy, Rotor Shredder 41 13422-E 1 Overload Protector

13 13722 1 Assy, Upper End Bell 42 12378 1 Clamp, Overload

(lncl.Codes14.22) 43 8221 2 Screw (8-32x1/2)

14 12936 1 Shield 44 13396 1 Box, Terminal Assy

15 1269 6 Screw (8-18x1/2) (Incl. code 46)

16 12934-A 1 Assy, Seal 45 12381 1 Screw (8-32x1-1/4)

17 12935 1 Sleeve, Spacer 46 12383 1 Grommet, Overload

18 12860 1 0-Ring 47 13709 1 Bearing, Lower

19 12319 1 Slinger 48 13678 1 Spring, Pre-load

20 12610 1 Assy, Upper Bearing 49 13710 1 End Frame, Lower

21 12326 1 Seal, Water & Oil 50 13676 1 Fan

22 11322 3 Key, Woodruff 51 13677 1 Ring, Retaining

23 13080 1 Kit, Bearing Seal (Incl. 52 12490 3 Tube, Spacer

Codes 9-11 &14-22) 53 11940-A 3 Bolt, Thru

24 11444 3 Washer, Lock 54 12396 1 Cover, Bottom

25 3135 3 Screw (1/4-20xl) 55 2466-A 1 Screw, Ground

26 1470 1 Gasket, Tailpipe 56 11757-B 2 Tube, Foot Assy.

27 5487 1 Tailpipe

(Optional)

28 1461 1 Flange, Tailpipe

29 1468 2 Screw (1/4-20x1/2)

30 13674-B 1 Rotor & Shaft Assy.

(Incl. Codes 31 & 47)

ISE

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-31 (C.S.A.)

(208/230/460VoK / 60Hz / 3 Phase)

Start Date:

02/26/93

Engineer Number:

13660-C

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

1 11004 1 Flange, Mounting 28 1461 1 Flange, Tailpipe

2 11016

1

Gasket, Mounting 29 1468 2 Screw (1/4-20x1/2)

3 11020-A

1

Body, Assy, Upper 30 13674-H 1 Rotor & Shaft Assy

4 1491 6 Screw (1/4-20x3/4)

(Incl. Code 43)

5 11227 1 Pipe, Plug 31 12370 1 Trim, Band

6 11006

1

Gasket, Shredder 32 1836-A 2 Screw (8-32x1/2)

7 12442

1

Body & Cover Assy 33 13714-B 1 Stator Assy

8 11252-A

1

Shredder, Stationary 34 12433-E 1 Bracket Assy

9 11260

1

Nut

(Mounting)

10 12445

1

Washer 35 11448 4 Screw (8-18x1/4)

11 12142 1 Washer, Fiber 36 12384 1 Bushing

12 12944 1 Shredder Assy, Rotor 37 13422-N 1 Overload, Protector

13 13722 1 End Bell Assy, Upper 38 12378 1 Clamp, Overload

(Incl. Codes 14 thru 22) 39 8221 2 Screw (8-32x1/2)

14 12936 1 Shield 40 13396 1 Box, Terminal

15 1269 6 Screw (8-18x1/2)

(Incl. code 42)

16 12934-A 1 Seal Assy 41 12381 1 Screw (8-32x1-1/4)

17 12935 1 Sleeve, Spacer 42 12383 1 Grommet, Overload

18 12860 1 O-Ring 43 13709 1 Bearing, Lower

19 12319 1 Slinger 44 13678 1 Spring, Pre-load

20 12610 1 Bearing Assy, Upper 45 13747 1 End Frame, Lower

21 12326 1 Seal, Water& Oil 46 13676 1 Fan

22 11322 3 Key, Woodruff 47 13677 1 Ring, Retaining

23 13080 1 Bearing Seal Kit (Incl. 48 12490 3 Tube, Spacer

codes 9-10-11 & 14 thru 22) 49 11940-A 3 Bolt, Thru

24 11444 3 Washer, Lock 50 12396 1 Cover, Bottom

25 3135 3 Screw (1/4-20x1/2) 51 2466-A 1 Screw, Ground

26 1470 1 Gasket, Tailpipe 52 11757-B 2 Tube Assy, Foot

27

5487

1

Tailpipe

(Optional)

1

H.P.

ENVIROVAC

COMMERCIAL DISPOSER

MODEL NO. SS100-32

(115/208/230 Volt / 50/SOHz /1 Phase)

Start Date:

02/19/93

Engineer Number:

13660-D

1H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE PART NO.

NO. NO. REQ. DESCRIPTION NO. NO. REQ. DESCRIPTION

1 11004

1

Flange, Mounting 31 1836-A 2 Screw (8-32x1/2)

2 11016

1

Gasket, Mounting 32 13713-B 1 Stator Assy

3 11020-A

1

Body, Assy, Upper 33 12433 1 Bracket Assy

4 1491 6 Screw (1/4-20x3/4)

(Mounting)

5 11227

1

Rug, Pipe 34 11448 4 Screw (8-18x1/4)

6 11000

1

Gasket, Shredder 35 11868 1 Capacitor

7 12442

1

Assy, Body & Cover 36 12378 1 Clamp, Overload

8 11252-A

1

Shredder, Stationary 37 8221 2 Screw (8-32x1/2)

9 11260 1 Nut 38 13396-E 1 Box, Terminal Assy

10 12445 1 Washer

(Incl. code 40)

11 12142 1 Washer, Fiber 39 12381 1 Screw (8-32x1-1/4)

12 13586 1 Assy, Rotor Shredder 40 13559 1 Plug, Button

13 13597-A 1 Assy, Upper End Bell 41 13422-BB 1 Overload Protector

(Incl. Coda* 14-22) 42 12384 1 Bushing

14 12936 1 Shield 43 2466-A 1 Screw, Ground

15 1269 6 Screw (8-18x1/2) 44 13709 1 Bearing, Lower

16 12934-A 1 Assy, Seal 45 13678 1 Spring, Pre-load

17 12935 1 Sleeve, Spacer 46 13710 1 End Frame, Lower

18 12860 1 0-Ring 47 13676 1 Fan

19 12319 1 Slinger 48 13677 1 Ring, Retaining

20 12610 1 Assy, Upper Bearing 49 12490 3 Tube, Spacer

21 12326 1 Seal, Water & Oil 50 12396 1 Cover, Bottom

22 11322 3 Key. Woodruff 51 11940-A 3 Bolt, Thru

23 13080 1 Kit. Bearing Seal (Ind. 52 11757-B 2 Tube, Foot Assy.

Codes 9-11 & 14-22)

(Optional)

24 11444 3 Washer, Lock

25 3135 3 Screw (1/4-20x1)

26 13592-C 1 Rotor & Shaft Assy.

(Incl. Codes 27 & 44)

27 1370S 1 Centrifugal Actuator

28 8221 2 Screw (8-32x1/2)

29 13707 1 Switch, Start

30 12370 1 Trim Band

Start Date:

02/19/93

ENVIROVAC

COMMERCIAL DISPOSER

MODEL NO. SS100-34

1 YR (208/230/380 Volt / 50 Hz / 3 Phase) 1 H.P.

FULL WRNTY

Engineer

Number

13660

-

G

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

NO.

PART

NO.

REQ.

DESCRIPTION

CODE

NO.

PART

NO.

REQ.

DESCRIPTION

1 11004 1 Flange, Mounting 30 12433-P 1 Bracket Assy

2

11016

1

Gasket, Mounting

(Mounting)

3 11020-A 1 Upper Body Assy 31 11448 4 Screw (8-18x1/4)

4 1491 6 Screw (1/4-20x3/4) 32 12378 1 Clamp, Overload

5 11227 1 Plug, Pipe 33 8221 2 Screw (8-32x1/2)

6 11006 1 Gasket. Shredder 34 13396-E 1 Box, Terminal Assy

7 12442 1 Body & Cover Assy

(Incl. code 36)

8

11252-A

1

Shredder, Stationary

35

12381

1

Screw (8-32x1-1/4)

9 11260 1 Nut 36 13559 1 Grommet, Overload

10

12445

1

Washer

37

13422-BE

1

Overload Protector

11 12142 1 Washer, Fiber 38 12384 1 Bushing

12 13588 1 Rotor Shredder Assy 39 2466-A 1 Screw, Ground

13

13928

1

Upper End Bell Assy

40

13709

1

Bearing, Lower

(lncl.Codes14.22) 41 13678 1 Spring, Pre-load

14 12936 1 Shield 42 13747 1 End Frame, Lower

15

13919

6

Screw (8-18x1/2)

43

13676

1

Fan

16 12934-A 1 Seal Assy 44 13677 1 Ring, Retaining

17 12935 1 Sleeve, Spacer 45 12490 3 Tube, Spacer

18

12860

1

0-Ring

46

12396

1

Cover, Bottom

19 12319 1 Slinger 47 11940-A 3 Bolt, Thru

20 12322 1 Upper Bearing Assy 48 11757-B 2 Tube, Foot Assy.

21 12326 1 Seal. Water & Oil

(Optional)

22 11322 3 Key, Woodruff

23 13080-A 1 Kit, Bearing Seal

(lncl. Codes 9-11&14-22)

24 11444 3 Washer, Lock

25 3135 3 Screw (1/4-20x1)

26 13592-E 1 Rotor & Shaft Assy.

(Incl. Codes 40)

27 12370 1 Trim Shell

28

1836-A

2

Screw (8-32x1/2)

29

13714

-

B

1

Stator

Assy

Start date:

04/21/93

ISE

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-35 (EXPORT)

(100 Volt / 50/60Hz /1 Phase)

Engineer

Number

13660

-

H

1 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO.

PART NO. NO. REQ. DESCRIPTION CODE NO.

PART NO. NO. REQ. DESCRIPTION

1 11004 1 Flange, Mounting 31 14131 1 Centrifugal Actuator

2 11016 1 Gasket, Mounting 32 8221 2 Screw (8-32x1/2)

3 11020-A 1 Body, Assy, Upper 33 13707 1 Switch, Start

4 1491 6 Screw (1/4-20x3/4) 34 12370 1 Trim Band

5 11227

1

Plug, Pipe 35 1836-A 2 Screw (8-32x1/2)

6 11006

1

Gasket, Shredder 36 13713-B 1 Stator Assy

7 12442

1

Assy, Body & Cover 37 12433 1 Bracket Assy

8 11252-A

1

Shredder, Stationary

(Mounting)

9 11260 1 Nut 38 11448 4 Screw (8-18x1/4)

10 12445

1

Washer 39 11868 1 Capacitor

11 12142

1

Washer. Fiber 40 12378 1 Clamp, Overload

12 12944 1 Assy, Rotor Shredder 41 8221 2 Screw (8-32x1/2)

13 13722

1

Assy, Upper End Bell 42 13396 1 Box, Terminal Assy

(Incl. Codes 14-22)

(Incl. code 48)

14 12936

Shield 43 12381 1 Screw (8-32x1-1/4)

15 1269 6 Screw (8-18x1/2) 44 12383 1 Grommet, Overload

16 12934-A

Assy, Seal 45 13422-T 1 Overload Protector

17 12935

Sleeve, Spacer 46 12384 1 Bushing

18 12860

0-Ring 47 2466-A 1 Screw, Ground

19 12319 1 Slinger 48 13709 1 Bearing, Lower

20 12610 1 Assy, Upper Bearing 49 13678 1 Spring, Pre-load

21 12326 1 Seal, Water & Oil 50 13710 1 End Frame, Lower

22 11322 3 Key. Woodruff 51 13676 1 Fan

23 13080 1 Kit, Bearing Seal (Incl. 52 13677 1 Ring, Retaining

Codes 9-11 & 14-22) 53 11940-A 3 Bolt, Thru

24 11444 3 Washer, Lock 54 12490 3 Tube, Spacer

25 3135 3 Screw (1/4-20x1) 55 12396 1 Cover, Bottom

26 1470 1 Gasket, Tailpipe 56 11757-B 2 Tube, Foot Assy.

27 5487 1 Tailpipe

(Optional)

28 1461 1 Flange, Tailpipe

29 1468 2 Screw (1/4-20x1/2)

30 13674-8 1 Rotor & Shaft Assy.

(Incl. Codes 31 & 48)

ENVIROVAC

COMMERCIAL DISPOSER

MODEL NO. SS100-36

(460 Volt / 60 Hz / 3 Phase)

Start Date:

11/29/93

Engineer Number:

13660-J

1 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

NO.

PART

NO.

REQ.

DESCRIPTION

CODE

NO.

PART

NO.

REQ.

DESCRIPTION

1

11

004

1

Flange, Mounting

30

12433

-

E

1

Bracket Assy

2 11016 1 Gasket, Mounting

(Mounting)

3 11020-A

1 Body, Assy, Upper 31 11448 4 Screw (8-18x1/4)

4 1491 6 Screw (1/4-20x3/4) 32 12378 1 Clamp, Overload

5 11227 1 Plug, Pipe 33 8221 2 Screw (8-32x1/2)

6 11006 1 Gasket, Shredder 34 13396-E

1 Box, Terminal Assy

7 12442 1 Assy, Body & Cover

(Incl. code 36)

8 13798 1 Shredder, Stationary 35 12381 1 Screw (8-32x1-1/4)

9 11260 1 Nut 36 12383 1 Grommet, Overload

10 12445 1 Washer 37

13422

-

BE

1 Overload Protector

11 12142 1 Washer, Fiber 38 12384 1 Bushing

12 13799 1 Assy, Rotor Shredder 39 2466 -A 1 Screw, Ground

13 13597-A

1 Assy, Upper End Bell 40 13709 1 Bearing, Lower

(Incl. Codes 14-22) 41 13678 1 Spring, Pre-load

14 12936 1 Shield 42 13710 1 End Frame, Lower

15 1269 6 Screw (8-18x1/2) 43 13676 1 Fan

16 12934-A

1 Assy, Seal 44 13677 1 Ring, Retaining

17 12935 1 Sleeve, Spacer 45 12490 3 Tube, Spacer

18 12860 1 O-Ring 46 12396 1 Cover, Bottom

19 12319 1 Slinger 47 11940-A

3 Bolt, Thru

20 12610 1 Assy, Upper Bearing 48 11757-B

2 Tube, Foot Assy

21 12326 1 Seal, Water & Oil

(Optional)

22 11322 3 Key, Woodruff

23 13080 1 Kit, Bearing Seal (Incl.

Codes 9-11 & 14-22)

24 11444 3 Washer, Lock

25 3135 3 Screw (1/4-20x1)

26 13592-E

1 Rotor & Shaft Assy.

(Incl. Codes 40)

27 12370 1 Trim Band

28 1836-A 2 Screw (8-32x1/2)

29 13657^J 1 Stator Assy

ENVIROVAC

COMMERCIAL DISPOSER

MODEL NO. SS100-37

(380 Volt / 50 Hz / 3 Phase)

Start Date:

11/29/93

Engineer Number:

13660-K

1 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

NO.

PART

NO.

REQ.

DESCRIPTION

CODE

NO.

PART

NO.

REQ.

DESCRIPTION

1 11004 1 Flange, Mounting 30 12433-E 1 Bracket Assy

2 11016 1 Gasket, Mounting

(Mounting)

3 11020-A 1 Body, Assy, Upper 31 11448 4 Screw(8-18x1/4)

4 1491 6 Screw (1/4-20x3/4) 32 12378 1 Clamp, Overload

5 11227 1 Plug, Pipe 33 8221 2 Screw (8-32x1/2)

6 11006 1 Gasket, Shredder 34 13396 1 Box, Terminal Assy

7 12442 1 Assy, Body & Cover

(Incl. code 36)

8 13803

1

Shredder, Stationary 35 12381 1 Screw(8-32x1-1/4)

9 11260

1

Nut 36 12383 1 Grommet, Overload

10 12445

1

Washer 37 13422-BE 1 Overload Protector

11 12142

1

Washer, Fiber 38 12384 1 Bushing

12 13799

1

Assy, Rotor Shredder 39 2466-A 1 Screw, Ground

13 13671 -L

1

Assy, Upper End Bell 40 13709 1 Bearing, Lower

(lncl.Codes14.22) 41 13678 1 Spring, Pre-load

14 12936 1 Shield 42 13710 1 End Frame, Lower

15 1269 6 Screw (8-18x1/2) 43 13676 1 Fan

16 12934-A 1 Assy, Seal 44 13677 1 Ring, Retaining

17 12935 1 Sleeve, Spacer 45 12490 3 Tube, Spacer

18 12860 1 0-Ring 46 12396 1 Cover, Bottom

19 12319 1 Slinger 47 11940-A 3 Bolt, Thru

20 12610 1 Assy, Upper Bearing 48 11757-B 2 Tube, Foot Assy.

21 12326 1 Seal, Water & Oil

(Optional)

22 11322 3 Key, Woodruff

23 13080 1 Kit, Bearing Seal (Incl.

Codes 9-11 &14-22)

24 11444 3 Washer, Lock

25 3135 3 Screw( 1/4-20x1)

26 13592-E 1 Rotor & Shaft Assy.

(Incl. Codes 40)

27 12370 1 Trim Band

28 1836-A 2 Screw (8-32x1/2)

29 13657-J 1 Stator Assy

Page is loading ...

In-Sink-Erator SS-100-1 User manual

This manual is also suitable for

In-Sink-Erator SS-100-1 User manual

Related papers

Other documents