Dometic 9500 .003 Installation guide

Brand: Dometic

Model: 9500 .003

Type: Installation guide

This manual is also suitable for

Dometic 9500 .003 is a case awning designed for use on RVs with straight sides, especially well suited for RVs with an over cab extension. It can be installed by one person with brief help from additional personnel. The awning is factory preset for a 5° fabric slope, but it may be adjusted for a steeper slope (up to 15°). It has a durable construction and provides protection from sun and rain. Whether you're camping, tailgating, or just enjoying the outdoors, the Dometic 9500 .003 is the perfect addition to your RV.

Read these instructions carefully. These

instructions MUST stay with this product.

USA

SERVICE OFFICE

Dometic Corporation

1120 North Main Street

Elkhart, IN 46514

CANADA

Dometic Corporation

46 Zatonski, Unit 3

Brantford, ON N3T 5L8

CANADA

SERVICE CENTER &

DEALER LOCATIONS

Please Visit:

www.eDometic.com

TYPE

9500

MANUAL

CASE / CASSETTE AWNING

MODEL

200(LL)(CC).003(#)

REVISION D

Form No. 3314492.000 09/16

(French 3314493.000_D)

LaGrange, IN 46761

INSTALLATION

INSTRUCTIONS

RECORD THIS INFORMATION FOR FUTURE

REFERENCE:

Model Number

Serial Number

Date Purchased

Retailer / Qualied Installer

TABLE OF CONTENTS

INTRODUCTION ....................................................................................................................................................................2

DOCUMENT SYMBOLS ........................................................................................................................................................2

IMPORTANT SAFETY INSTRUCTIONS ................................................................................................................................ 3

A. Recognize Safety Information ...................................................................................................................................3

B. Understand Signal Words ..........................................................................................................................................3

C. Supplemental Directives ............................................................................................................................................ 3

D. General Safety Messages .........................................................................................................................................3

GENERAL INFORMATION .....................................................................................................................................................3

A. Required Tools ...........................................................................................................................................................3

B. Required Hardware ...................................................................................................................................................3

C. Additional Hardware Quantity .................................................................................................................................... 3

SPECIFICATIONS .................................................................................................................................................................. 4

A. Door Clearance .........................................................................................................................................................4

B. Awning Dimensions ...................................................................................................................................................4

INSTALLATION ......................................................................................................................................................................5

A. Determine Awning Location ....................................................................................................................................... 5

B. Install Mounting Bracket ............................................................................................................................................6

C. Install Awning .............................................................................................................................................................7

ADJUSTMENTS (OPTIONAL) ...............................................................................................................................................8

A. Adjust Fabric Slope (If Desired) .................................................................................................................................8

B. Adjust Lateral Arm Assemblies (If Required) .............................................................................................................8

C. Adjust Lead Rail Alignment (If Required) .................................................................................................................10

VERIFY INSTALLATION.......................................................................................................................................................10

A. Test Operation .........................................................................................................................................................10

B. Secure Awning For Travel .......................................................................................................................................10

C. Keep Literature ........................................................................................................................................................10

INTRODUCTION

This case awning (hereinafter referred to as “awning,” or “product”) is designed and intended for use on RVs with straight

sides. It is especially well suited for RVs with an over cab extension where there is not sufcient surface for a bottom mount-

ing bracket. This product can be installed by one person with brief help from additional personnel. Use these instructions to

ensure correct installation and function of product.

Dometic Corporation reserves the right to modify appearances and specications without notice.

DOCUMENT SYMBOLS

Indicates additional information that is NOT related

to physical injury.

Indicates step-by-step instructions.

IMPORTANT SAFETY INSTRUCTIONS

This manual has safety information and instructions to help

you eliminate or reduce the risk of accidents and injuries.

A. Recognize Safety Information

This is the safety alert symbol. It is used to

alert you to potential physical injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

B. Understand Signal Words

A signal word will identify safety messages and

property damage messages, and will indicate the

degree or level of hazard seriousness.

 indicates a hazardous situation that,

if NOT avoided, could result in death or serious in-

jury.

 indicates a hazardous situation that,

if NOT avoided, could result in minor or moderate

injury.

 is used to address practices NOT

related to physical injury.

C. Supplemental Directives

Read and follow all safety information and

instructions to avoid possible injury or death.

Read and understand these instructions be-

fore [installing / using / servicing / performing

maintenance on] this product.

Incorrect [installation / operation / servicing /

maintaining] of this product can lead to seri-

ous injury. Follow all instructions.

The installation MUST comply with all ap-

plicable local and national codes, including

the latest edition of the following standards:

U.S.A.

● ANSI/NFPA70, National Electrical Code

(NEC)

● ANSI/NFPA 1192, Recreational Vehicles

Code

CANADA

● CSA C22.1, Parts l & ll, Canadian Electri-

cal Code

● CSA Z240 RV Series, Recreational

Vehicles

D. General Safety Messages

 Failure to obey the following warn-

ings could result in death or serious injury:

● This product MUST be [installed / serviced] by a

qualied service technician.

● Do NOT modify this product in any way. Modica-

tion can be extremely hazardous.

GENERAL INFORMATION

A. Required Tools

● Electric Drill (optional)

● Torque Wrench

● Phillips Screwdriver / Bit

● 3 mm Hex Key / Driver / Bit

● 6 mm Hex Key / Driver / Bit

● 6 mm Hex Key Socket

● 10 mm Socket

B. Required Hardware

8′ - 13′ Models:

(1) Mounting Bracket

(12) M6 X 50 mm L Carriage Bolt

(12) M6 Split Lock Washer

(12) M6 Flat Washer

(12) M6 Locknut With Nylon Insert

(6) #8-18 X .38 Self Drilling Flat Head Screw

C. Additional Hardware Quantity

15′ - 16′ Models ONLY:

(4) M6 X 50 mm L Carriage Bolt

(4) M6 Split Lock Washer

(4) M6 Flat Washer

(4) M6 Locknut With Nylon Insert

(2) #8-18 X .38 Self Drilling Flat Head Screw

A. Door Clearance

 Allow for sufcient clearance be-

tween awning fabric and entry door to accommo-

date awning pitch (slope).

Awning is factory preset for a 5° fabric slope, but

it may be adjusted for a steeper slope (up to 15°).

See (FIG. 1).

For a 22″ entry door, the approximate mini-

mum clearance is 2-1/2″ for 5° slope, and 6

1/2″ for 15° slope.

Make sure mounting surface on RV is at

and vertical. Any tilt in mounting surface will

tilt awning, and affect awning pitch (slope).

FIG. 1

Avoid

Interference

RV Door (Open)

2 1/2″

22″

5°

Typical Conguration Shown

B. Awning Dimensions

 IMPACT OR CRUSH HAZARD. Lo-

cate mounting bolts behind each shoulder assem-

bly (lateral arm attachment) to provide proper sup-

port. Otherwise, awning may become unstable and

could bend or collapse. Failure to obey this warning

could result in death or serious injury.

Mounting bracket (bolt hole pattern) spacing varies

by length. See (FIG. 2).

● 8′ - 13′ models require (3) sets of bolts.

● 15′ - 16′ models require (4) sets of bolts.

Spacing MUST provide mounting bolts be-

hind each shoulder assembly (lateral arm at-

tachment). See (FIG. 3).

FIG. 2

1 3/8″

3 3/16″

Back View

Right

Left

6 3/8″

4″

1 1/2″

Hole Pattern Locations

8′ 10′ 12′ 13′ 15′ 16′

A 5 7/8″

B N/A 60 3/8″

C 48 3/8″ 60 5/8″ 69″ 78 13/16″ 115 7/8″

D 90 3/4″ 115 7/16″ 132 1/8″ 151 7/8″ 180 3/8″ 190 3/8″

E 103″ 123 1/2″ 140 1/4″ 159 7/8″ 188 1/2″ 199 1/4″

FIG. 3

15′ - 16′ Model Shown

Mounting Bolts

Shoulder Assembly

SPECIFICATIONS

FIG. 5

RV Wall (Structure Not Shown)

Sleeves (Optional

-Installer Cut To Length)

Mounting

Bracket

Backing Plate

(Optional-Installer Supplied)

Carriage Bolts (Provided

-Installer Cut To Length)

FIG. 6

RV Wall

Thickness

(-) 1/16″

(Cut Line)

(+) 9/16″

(Cut Line)

Sleeve

(Optional)

Carriage

Bolt

2.  Allow for sufcient clearance be-

tween awning fabric and entry door to accom-

modate awning pitch (slope).

Avoid location that interferes with entry door

swing when awning is completely extended. See

subsection, “A. Door Clearance” on page (4).

3. Maintain a minimum of 1/2″ clearance at top and

sides of awning case.

Additional clearance is recommended to

allow easier access for servicing.

A. Determine Awning Location

1. Structural backing:

 IMPACT OR CRUSH HAZARD.

Make sure mounting surface on RV is at, has

solid structural backing where fasteners pene-

trate surface, and will safely and securely sup-

port product. Otherwise, product may become

unstable and could [detach / bend / collapse].

Failure to obey this warning could result in death

or serious injury.

Solid structural backing must be as wide as

mounting bolt pattern (behind each shoulder as-

sembly), and span from oor to roof of RV.

a. Best practice:

Find a solid structure in RV wall for support

of mounting bracket (when possible). See

(FIG. 4).

FIG. 4

Mounting Bracket

RV Wall

(Solid Structure Shown)

b. If sufcient structural support is NOT pres-

ent, proceed to step (c). Otherwise, skip to

step (2).

c. Alternative:

When sufcient structural support is NOT

present, use backing plate (installer sup-

plied) and sleeves (installer supplied) inside

RV wall. This will help strengthen awning

support. See (FIG. 5).

Cut sleeves and carriage bolts (Grade

8.8 minimum) to t RV wall as neces-

sary. Repair threads (at cut) on car-

riage bolts. See (FIG. 6).

For RV wall thickness up to 1-7/16″,

use the M6 carriage bolts provided.

For RV wall thickness over 1-7/16″,

longer carriage bolts are required.

INSTALLATION

5.  IMPACT OR CRUSH HAZARD.

Do NOT over-tighten fasteners. Applying too

much torque may cause fasteners/threads to

fail, and could allow product to collapse. Failure

to obey this warning could result in death or seri-

ous injury.

 ALWAYS use sealant on (clean)

parts and surfaces where fasteners enter RV’s

[walls / roof / oor]. Otherwise, water leakage

could occur.

Apply sealant along entire top edge of mount-

ing bracket (where it contacts RV’s wall), and

around drilled holes. Then place and tighten car-

riage bolts (with locknuts, and washers) through

mounting bracket and drilled holes in RV wall.

See (FIG. 4) & (FIG. 8).

Tighten to 35 ±5 in·lb torque.

If solid structure is NOT present, use

backing plates and sleeves. See (FIG. 5).

Alternative fasteners may be used only if

size and strength requirements are met for

safe installation and operation of awning.

Bolt head MUST be no taller than 1/8″.

See subsection, “A. Determine Awning

Location” on page (5) for more fasten-

er and wall thickness requirements.

Sealant

FIG. 8

B. Install Mounting Bracket

1.  Install mounting bracket(s) on a

at surface, and level to ensure correct function

and appearance.

Using the mounting bracket as a template, mark

its position and all hole locations. See (FIG. 2).

2. Mark a line between the (2) outside top holes,

and between the (2) outside bottom holes. See

(FIG. 7).

FIG. 7

Horizontal Line

Between Outside

Bottom Holes

Horizontal Line

Between Outside

Top Holes

Vertical

(Intersecting)

Line

3. Verify horizontal lines are level. Then mark ver-

tical lines from all remaining holes to intersect

marked horizontal lines. See (FIG. 7).

Due to the nature of long extruded parts,

the mounting bracket may be slightly

bowed. Some hole locations may be

above or below marked horizontal lines.

4.  FIRE OR ELECTRICAL SHOCK

HAZARD. Make sure there are no obstacles

(wires, pipes, etc.) inside RV’s [roof / oor /

walls]. Shut OFF gas supply, disconnect 120

Vac power from RV, and disconnect positive (+)

12 Vdc terminal from supply battery BEFORE

drilling or cutting into RV. Failure to obey these

warnings could result in death or serious injury.

Drill 1/4″ clearance holes for M6 carriage bolts

on the marked (intersecting) locations. See

(FIG. 2) & (FIG. 7).

If sleeves (installer supplied) are used,

larger clearance holes are necessary. Drill

appropriately sized clearance holes to ac-

commodate sleeves.

INSTALLATION

C. Install Awning

1.  LIFTING HAZARD. Use proper

lifting technique and control when lifting product.

Failure to obey this caution could result in injury.

With a mechanical lift, or the help of additional

personnel, lift awning up to mounting bracket.

Do NOT hook onto mounting bracket until

wiring is routed.

2. With the help of additional personnel, hook aw-

ning onto mounting bracket. See (FIG. 9).

FIG. 9

Mounting Bracket

Sleeves (Optional

-Installer Cut To Length)

RV Wall (Structure Not Shown)

Backing Plate

(Optional-Installer Supplied)

Awning

3.  IMPACT OR CRUSH HAZARD. Do

NOT extend awning until it is securely [mounted

/ hooked] onto mounting bracket(s). Take special

care when extending. Otherwise, awning could

dislodge and fall. Failure to obey this warning

could result in death or serious injury.

Carefully extend awning approximately 1′. Then

verify awning’s back rail is fully contacting mount-

ing bracket’s vertical surface. See (FIG. 10).

FIG. 10

Back Rail

Mounting

Bracket

No Gap

4.  IMPACT OR CRUSH HAZARD.

Do NOT operate or leave awning unattended un-

til it is securely fastened to mounting bracket(s).

Otherwise, awning could dislodge and fall. Fail-

ure to obey this warning could result in death or

serious injury.

Place and tighten self drilling screws through

mounting bracket and into awning’s back rail.

See (FIG. 11).

FIG. 11

Self

Drilling

Screw

Backing

Plate

(Optional-

Installer

Supplied)

Awning

Mounting

Bracket

Back Rail

Sleeves

(Optional

-Installer Cut

To Length)

FIG. 14

Shoulder Bracket

Pitch Adjustment

Screw

Collet Clamp Screws Back Shoulder Collet

Lateral Arm

Assembly

5.  PINCH HAZARD. Keep CLEAR

of pivot area while raising or lowering lateral arm

assembly. Failure to obey this caution could re-

sult in injury.

Carefully loosen pitch adjustment screw, and

pivot lateral arm assembly down (lower lead

rail) until it is in desired position. See (FIG. 12)

& (FIG. 14).

6. Tighten both collet clamp screws to 140 in·lb

torque to re-clamp back shoulder collet. See

(FIG. 14).

7. Repeat steps (4) through (6) for each lateral arm

assembly.

8. Remove ties from lateral arm assemblies when

done.

9. Verify awning will close without interference.

See subsection, “B. Adjust Lateral Arm

Assemblies (If Required)” on page (8)

if adjustments are necessary.

See subsection, “C. Adjust Lead Rail

Alignment (If Required)” on page (10)

to adjust lead rail alignment.

B. Adjust Lateral Arm Assemblies (If

Required)

 Do NOT allow lateral arm assem-

blies to rub against lower lip of back rail when clos-

ing, or allow awning fabric to contact shoulder base

when fully opened. Otherwise, premature wear and

abrasions could occur.

If awning will not close correctly, or if lateral arm as-

sembly’s elbow will not clear back rail, it will require

adjustment. See (FIG. 15).

The lateral arm assembly’s elbow should just

clear (slightly above) lower lip of back rail

without rubbing. Adjusting too high may in-

terfere with top (awning case), or may cause

shoulder base to contact awning fabric.

A. Adjust Fabric Slope (If Desired)

This awning is factory preset for a 5° fabric slope to

help accommodate water runoff. Alternatively, the

awning may be set for a steeper slope (up to 15°)

if adequate clearance (for door, etc.) is available.

See (FIG. 12).

FIG. 12

5° Slope

(Factory Preset)

1. Extend awning far enough (approximately 1′) to

access shoulder assembly. See (FIG. 13).

FIG. 13

Lateral Arm Assembly

Strapping

1′

Near Shoulder

Assembly

Near Wrist Assembly

Lead Rail

2. Tie all lateral arm assemblies securely (with

fabric strapping or light rope) near shoulder and

wrist. See (FIG. 13).

3. Support weight of lead rail and lateral arm as-

semblies securely.

4.  IMPACT OR CRUSH HAZARD.

Make sure lateral arm assemblies are tied and

supported securely (with lead rail) before loos-

ening fasteners. Otherwise, the lead rail and lat-

eral arm assemblies could shift or drop quickly

and unexpectedly. Failure to obey this warning

could result in death or serious injury.

Loosen collet clamp screws (clamping back

shoulder collet) on (1) lateral arm assembly

ONLY. See (FIG. 14).

ADJUSTMENTS (OPTIONAL)

FIG. 15

Elbow Clearance

Lateral Arm

Assembly

Top

Back Rail

Shoulder

Bracket

1. Extend awning far enough (approximately 1′) to

access pivot clamp screws. See (FIG. 16).

FIG. 16

Shoulder Bracket

Lateral Arm

Assembly

(Top Front) Tilt

Adjustment Screw

(Top Back) Tilt

Adjustment Screw

Shoulder Pivot

Pivot Clamp

Screws

2. Support weight of lead rail and lateral arm as-

semblies securely.

3.  IMPACT OR CRUSH HAZARD.

Make sure lead rail and lateral arm assemblies

are supported securely before loosening fasten-

ers. Do NOT completely remove fasteners, or

loosen them so far that shoulder base will dis-

engage from shoulder bracket. Otherwise, the

lead rail and lateral arm assemblies could shift

or drop quickly and unexpectedly, or lateral arm

assemblies could extend to the side (beyond

awning perimeter) quickly and unexpectedly.

Failure to obey this warning could result in death

or serious injury.

Slightly loosen pivot clamp screws (clamping

front shoulder collet to shoulder pivot). See

(FIG. 16) & (FIG. 17).

Loosen screws just enough to relieve

clamping pressure on components.

Repeat this step for each lateral arm as-

sembly requiring adjustment.

FIG. 17

(Top) Tilt Adjustment

Screw(s)

(Bottom) Tilt Adjustment

Screw(s)

Back Shoulder

Collet

Front Shoulder Collet

Pivot Clamp Screw

Shoulder Pivot

4. Retract awning until lateral arm assembly’s el-

bow meets top and back rail to check for clear-

ance. See (FIG. 15).

Allow enough gap to access top and bot-

tom tilt adjustment screws.

5. Adjust lateral arm assembly’s closing height.

See (FIG. 15), (FIG. 16), & (FIG. 17).

Repeat this step for each lateral arm as-

sembly requiring adjustment.

a. To increase (raise) elbow clearance:

I. Loosen (top front) & (bottom back) tilt

adjustment screws far enough to allow a

generous range of movement.

II. Tighten (top back) tilt adjustment screw.

III. Tighten (bottom front) tilt adjustment

screw.

IV. Repeat steps (II) through (III) as neces-

sary.

V. When desired clearance is reached, tight-

en (top front) & (bottom back) tilt adjust-

ment screws to clamp in place.

b. To decrease (lower) elbow clearance:

I. Loosen (top back) tilt adjustment screw.

II. Loosen (bottom front) tilt adjustment

screw.

III. Repeat steps (I) through (II) as neces-

sary.

IV. When desired clearance is reached, tight-

en (top front) & (bottom back) tilt adjust-

ment screws to clamp in place.

6. When you reach the appropriate clearance (for

ALL lateral arm assemblies), extend awning far

enough (approximately 1′) to access pivot clamp

screws.

VERIFY INSTALLATION

4. Retract awning again to check alignment of lead

rail against top and end caps.

5. Repeat steps (2) through (4) as necessary.

FIG. 18

Lead Rail

Wrist Pivot

Lateral Arm

Assembly

Top

Adjustment

Screw

RH End

Cap

Wrist Bracket

7. Tighten both pivot clamp screws to 140 in·lb

torque (to clamp front shoulder collet to shoul-

der pivot).

Repeat this step for each lateral arm as-

sembly.

8. Verify awning will close without interference.

See subsection, “C. Adjust Lead Rail

Alignment (If Required)” on page (10)

to adjust lead rail alignment.

C. Adjust Lead Rail Alignment (If Required)

After fabric slope and lateral arm assembly adjust-

ments, the lead rail may need realignment with top

and end caps. See (FIG. 18).

1. Check alignment of lead rail against top and end

caps.

2. Extend awning far enough (approximately 6″) to

access adjustment screw in wrist pivot.

3. Tilt lead rail, by turning adjustment screw in wrist

pivot (for each lateral arm assembly), until align-

ment appears correct.

a. Turn clockwise to tilt lead rail forward.

b. Turn counter-clockwise to tilt lead rail back.

A. Test Operation

Operate awning according to Operating Instruc-

tions to verify all parts are functioning correctly.

B. Secure Awning For Travel

1. Fully close awning. See “Close Awning” in Oper-

ating Instructions.

2. Verify awning is secure for travel. See “Prepare

Awning For Travel” in Operating Instructions.

C. Keep Literature

Instructions contain valuable information for prod-

uct use and consumer safety.



Keep BOTH the Installation and Operat-

ing Instructions with product.

ADJUSTMENTS (OPTIONAL)

Dometic 9500 .003 Installation guide

Brand: Dometic

Model: 9500 .003

Type: Installation guide

This manual is also suitable for

Download PDF

report

Dometic 9500 .003 Installation guide

This manual is also suitable for

Dometic 9500 .003 Installation guide

Related papers

Other documents