GB
Unpacking
11
Operating Your Remote Control
22
Installing the Base Stand
33
Quick Start Guide
L46FE12
Thank you for purchasing your new Logik T V.
Your new TV incorporates the latest technology to enhance your
viewing experience. We would suggest that you allow about 20
mins for initial setup.
Please follow this guide for a successful rst time installation.
Remove all packaging from the TV. Retain the packaging. If you
dispose of it please do so according to any local regulations.
1. Lay the TV down on a at surface with the back side facing up.
Please make sure a soft cushioned material (such as a pillow or
thick piece of foam) is placed beneath the screen.
2. To install the TV stand, rst attach the base stand to the TV.
Align the screw holes then secure with a screw driver (not
included) using the 6 screw A provided to x the base stand to
the TV
Install the batteries correctly by following the polarity
(+ and -) indications in the battery compartment.
The screw holes will only align if the front of the base
stand is at the front of the TV.
1. Press and lift the back
cover up to open the
battery compartment
of the remote control.
2. Insert two AAA size
batteries. Close the
battery compartment
cover.
46” Full HD LED TV
Screw A x 6
(P.N.: 100-016-4011)
TV with Stand Support
TV Base
Digital Switchover
Addendum
Remote Control /
AAA Batteries x 2
Screw A x 6
Screw B x 5
Instruction Manual
Quick Start Guide
AV Cable
TV Front
Base Stand
Front
screw
Turning the TV On for the First Time
66
Connecting to the Mains Socket
55
Connecting the Aerial
44
Connect one end of the RF coaxial cable to the aerial socket on the
wall and the other end of the cable to the RF (75Ω) socket at the rear
right side of your TV.
1. Connect the mains cable to the mains socket after you have
completed all the connections.
2. Switch on the POWER ON/OFF switch which is located at the front
right side under the frame. At this stage, the TV switches to standby
mode. The red LED indicator will illuminate on the front panel of the
TV.
3. In standby mode, press the / I button at the front right side panel
of the TV or the button on the remote control to turn the TV on.
The red LED indicator will turn blue.
Do not connect the TV to the mains supply until you
have completed all the connections.
(P.N.: 002-L39-LOGIK)
Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these
features, please take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call our UK Call Centre on 0844 561 1234.
Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
To mains
socket
HDMI1 IN
HDMI2 IN
PC IN
RF Coxial Cable
(not included)
OR
Please ensure aerial is plugged in!!
Then press OK button to start
Country
France
Germany Portugal
Italy Spain
UK
Menu
Channel Tuning
TV : 0 Channel
DTV : 0 Channel
Radio : 0 Channel
Data : 0 Channel
1 %... 471.25 MHz (TV)
Please press MENU key to skip
Please select an OSD Language
Deutsch
Español Français
Português Italiano
English
The first time you turn the TV on, it will go straight into First Time Installation menu.
1. Press the OK button to
start First Time
Installation menu.
4. Channel tuning will
commence. This operation
may take up to 6 minutes.
The display will show the
progress of the tuning and
the number of channels
found.
2. Press the buttons
to select English as your
desired language to be
displayed on the menu.
Press the OK button to
confirm.
3. Press the
buttons to select UK as
the country where you
will operate the TV.
Press the OK button to
confirm.
-
1
