KT-Elektronik SOL3-5 Quick Installation And Operating Manual

Brand: KT-Elektronik

Model: SOL3-5

Type: Quick Installation And Operating Manual

This manual is also suitable for

SOL3-7

Solar and differential temperature controller

SOL3-5

Quick installation and

operating manual

Firmware version 1.07,

June 2011

Quick installation and operating manual KT-Elektronik

Disclaimer of liability

We are constantly developing our products and therefore, reserve the right to change the product or the information

contained in this document at any time without notice.

We do not assume any liability for the accuracy or completeness of these mounting and operating instructions. Moreover, we

do not guarantee that the buyer can use the product for an intended purpose. Excluded are any liability for claims by the

buyer, especially claims for compensation including lost profits or any other financial loss, except the damage was caused

intentionally or by gross negligence. If an essential term of the contract is breached by negligence, our liability is limited to

the foreseeable damage.

Important safety instructions

For your own safety, observe the following instructions on the installation, start up and operation of the controller:

The device may only be installed, started up or operated by trained and experienced

personnel familiar with the product.

The controller has been designed for use in electrical power systems. For wiring and

maintenance, you are required to observe the relevant safety regulations.

Content

Installation......................................................................................................................................................................................3

Mounting................................................................................................................................................................................3

Electrical connection..............................................................................................................................................................3

Systems.........................................................................................................................................................................................5

Operation and display....................................................................................................................................................................7

Operating controls.................................................................................................................................................................7

Display...................................................................................................................................................................................8

Information level....................................................................................................................................................................9

Setting the controller time......................................................................................................................................................9

Check and modify times-of-use...........................................................................................................................................10

Check and set party mode...................................................................................................................................................10

Setting the system code number (selection of the hydraulic scheme)................................................................................11

Activating and deactivating funktions .................................................................................................................................11

Modify parameters...............................................................................................................................................................12

Resetting to default values..................................................................................................................................................13

Important key numbers........................................................................................................................................................13

Manual mode.......................................................................................................................................................................13

Function block lists......................................................................................................................................................................14

CO1: Heating circuit Rk1.....................................................................................................................................................14

CO3: Solar circuit.................................................................................................................................................................14

CO4: DHW heating .............................................................................................................................................................15

CO5: System-wide functions ..............................................................................................................................................15

CO6: Modbus.......................................................................................................................................................................15

Parameter lists.............................................................................................................................................................................16

PA1: Heating circuit.............................................................................................................................................................16

PA3: Solar circuit.................................................................................................................................................................16

PA4: Auxilary heating – Storage tank temperature.............................................................................................................17

PA5: System-wide parameters............................................................................................................................................17

PA6: Modbus communikation..............................................................................................................................................17

Technical specification.................................................................................................................................................................19

Material........................................................................................................................................................................................19

2 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

The SOL3-5 is a controller for solar thermal systems, and includes at max. nine temperature sensor inputs, five switching

outputs, one pulse input and one 0-10V input or output.

The controller is ready to use with the temperatures and operating schedules preset by the manufacturer. On start-up, the

current time and date need to be set at the controller.

This Quick manual contains necessary information for installation and start up.

Further informations are available at http://www.KT-Elektronik.de.

Document Content

Mounting and operating instructions detailed decription of the device characteristics

System schemes Schemes of all supported hydraulic systems

Installation

Mounting

Panel mounting Top hat rail mounting Wall mounting

Electrical connection

The wiring diagram is shown on the back side of the housing. This diagram is usable for most of the supported systems. In

some special configurations, the switching output connections are different. The sheet below are showing the terminal-

assignmet for all available system schemes.The terminal-assignment for inputs is valid for all systems.

Not to required sensors must not be connected.

KA_37386_SOL3-5_EN001 3

Quick installation and operating manual KT-Elektronik

System T. 21 T. 23 T. 24 T. 26 T. 27 T. 29 T. 30

I - I.0.0

CP1

I - I.0. I

CP1 UP M- M+

I - I. I.0

CP1 NH

I - I. I. I

CP1 NH UP M- M+

I - I.2.0

CP1 ZP

I - I.2. I

CP1 ZP UP M- M+

I - I.3.0

CP1 ZP NH

I - 2.0.0

CP1 SUV

I - 2.0. I

CP1 SUV UP M- M+

I - 2. I.0

CP1 SUV NH

I - 2.2.0

CP1 SUV ZP

I – 2.3.0

CP1 SUV ZP NH

I - 3.0.0

SP1 SP2

I - 3.0. I

SP1 SP2 UP M- M+

I - 3. I.0

SP1 SP2 NH

I - 3.2.0

SP1 SP2 ZP

I – 3.3.0

SP1 SP2 ZP NH

I o I.0.0

CP1 CTP

I o I.0. I

CP1 CTP UP M- M+

I o I. I.0

CP1 CTP NH

I o I.2.0

CP1 CTP ZP

I o I.3.0

CP1 CTP ZP NH

I o 2.0.0

CP1 CTP SUV

I o 2. I.0

CP1 CTP SUV NH

I o 2.2.0

CP1 CTP SUV ZP

I o 2.30

CP1 CTP SUV ZP NH

I o 3.0.0

CP1 SP1 SP2

I o 3. I.0

CP1 SP1 SP2 NH

I o 3.2.0

CP1 SP1 SP2 ZP

I o 3.3.0

CP1 SP1 SP2 ZP NH

2 - I.0.0

CP1 CUV

2 - I.0. I

CP1 CUV UP M- M+

2 - I. I.0

CP1 CUV NH

2 - I.2.0

CP1 CUV ZP

2 - I.3.0

CP1 CUV ZP NH

2 - 2.0.0

CP1 CUV SUV

System T. 21 T. 23 T. 24 T. 26 T. 27 T. 29 T. 30

2 - 2. I.0

CP1 CUV SUV NH

2 - 2.2.0

CP1 CUV SUV ZP

2 – 2.3.0

CP1 CUV SUV ZP NH

2 - 3.0.0

CUV SP1 SP2

2 - 3. I.0

CUV SP1 SP2 NH

2 - 3.2.0

CUV SP1 SP2 ZP

2 – 3.3.0

CUV SP1 SP2 ZP NH

2 o I.0.0

CP1 CUV CTP

2 o I. I.0

CP1 CUV CTP NH

2 o I.2.0

CP1 CUV CTP ZP

2 o I.3.0

CP1 CUV CTP ZP NH

2 o 2.0.0

CP1 CUV CTP SUV

2 o 2. I.0

CP1 CUV CTP SUV NH

2 o 2.2.0

CP1 CUV CTP SUV ZP

2 o 3.0.0

CP1 CUV SP1 SP2

2 o 3. I.0

CP1 CUV SP1 SP2 NH

2 o 3.2.0

CP1 CUV SP1 SP2 ZP

3 - I.0.0

CP1 CP2

3 - I.0. I

CP1 CP2 UP M- M+

3 - I. I.0

CP1 CP2 NH

3 - I.2.0

CP1 CP2 ZP

3 - I.3.0

CP1 CP2 ZP NH

3 - 2.0.0

CP1 CP2 SUV

3 - 2. I.0

CP1 CP2 SUV NH

3 - 2.2.0

CP1 CP2 SUV ZP

3 – 2.3.0

CP1 CP2 SUV ZP NH

3 o I.0.0

CP1 CP2 CTP

3 o I. I.0

CP1 CP2 CTP NH

3 o I.2.0

CP1 CP2 CTP ZP

3 o I.3.0

CP1 CP2 CTP ZP NH

3 o 2.0.0

CP1 CP2 CTP SUV

3 o 2. I.0

CP1 CP2 CTP SUV NH

3 o 2.2.0

CP1 CP2 CTP SUV ZP

3 o 3.0.0

CP1 CP2 SP1 SP2

3 o 3. I.0

CP1 CP2 SP1 SP2 NH

3 o 3.2.0

CP1 CP2 SP1 SP2 ZP

4 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

Systems

The SOL3-5 provides 72 different hydraulic systems. These differs in basic system components and extentions.

Basic system components Extentions

•number of collector arrays,

•number of storage tanks,

•switching between collector arrays and storage tanks using

valves or pumps,

•internal (or non) or external heat exchanger

•heating circuit,

•auxilary heater,

•circulation pump

The system variants are characterised about a multi-digit system identifier for the choice by basic system components and

extentions. The order of the system identifier becomes clear with the help of the followed shown hydraulic systems.

The schemes below are only schemes, without any kind of basic valves and security equipement. A system scheme is

identified by a explicit system schema indicator (e.g. I o 2. I.0)

System I  I.0.0

1 collector array, 1 storage tank

System 2  I.0.0

2 collector arrays (valve),

1 storage tank

System 3  I.0.0

2 collector arrays (2 pumps),

1 storage tank

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

CP1

Speicher1

Kollektor-

feld 1

CF1CF1

SF 1

CP 1

Kollektor-

feld 2

CF2

CUV

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

Kollektor-

feld 2

CP 2

CF2

CP1

System I o I.0.0

1 collector array, 1 storage tank,

external heat exchanger

System 2 o I.0.0

2 collector arrays (valve),

1 storage tank, external heat exchanger

System 3 o I.0.0

2 collector arrays (2 pumps),

1 storage tank, external heat exchanger

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

CP1

CT P

Speicher1

Kollektor-

feld 1

CF1CF1

SF 1

CP 1

CTP

Kollektor-

feld 2

CF2

CUV

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

CT P

Kollektor-

feld 2

CP2

CF2

CP 1

System I  2.0.0

1 collector array, 2 storage tanks (valve)

System 2  2.0.0

2 collector arrays (valve),

2 storage tanks (valve)

System 3  2.0.0

2 collector arrays (2 pumps),

2 storage tanks (valve)

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

CP1

SF 2

Speicher2

SUV

Speicher1

Kollektor-

feld 1

CF1CF1

SF 1

CP 1

Kollektor-

feld 2

CF2

CUV

SF 2

Speicher2

S UV

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

Kollektor-

feld 2

CP2

CF2

CP 1

SF 2

Speicher2

S UV

KA_37386_SOL3-5_EN001 5

Quick installation and operating manual KT-Elektronik

System I o 2.0.0

1 collector array, 2 storage tanks (valve),

external heat exchanger

System 2 o 2.0.0

2 collector arrays (valve),

2 storage tanks (valve),

external heat exchanger

System 3 o 2.0.0

2 collector arrays (2 pumps),

2 storage tanks (valve),

external heat exchanger

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

CP1

CTP

SF 2

Speicher2

SUV

Speicher1

Kollektor-

feld 1

CF1CF1

SF 1

CP 1

Kollektor-

feld 2

CF2

CUV

SF 2

Speicher2

CTP

S UV

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

Kollektor-

feld 2

CP2

CF2

CP 1

SF 2

Speicher2

CT P

S UV

System I o 3.0.0

1 collector array,

2 storage tanks (2 pumps),

external heat exchanger

System 2 o 3.0.0

2 collector arrays (valve),

2 storage tanks (2 pumps),

external heat exchanger

System 3 o 3.0.0

2 collector arrays (2 pumps),

2 storage tanks (2 pumps),

external heat exchanger

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

CP1

SP 2

S P1

SF 2

Speicher2

SP 2

S P1

Speicher1

Kollektor-

feld 1

CF1CF1

SF 1

CP 1

SP 2

S P1

Kollektor-

feld 2

CF2

CUV

SF 2

Speicher2

SP 2

S P1

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

SP 2

S P1

Kollektor-

feld 2

CP2

CF2

CP 1

SF 2

Speicher2

SP 2

S P1

System I  3.0.0

1 collector array,

2 storage tanks (2 pumps)

System 2  3.0.0

2 collector arrays (valve),

2 storage tanks (2 pumps)

Speicher1

Kollektor-

feld 1

CF1CF1

S F1

SF 2

Speicher2

SP 2

S P1

Speicher1

Kollektor-

feld 1

CF1CF1

SF 1

SF 2

Speicher2

Kollektor-

feld 2

CF2

CUV

SP 2

S P1

Every shown schemes above could be extend with some additional functions. The extentions (e.g.heating circuit, auxilary

heating and circutation) can be combined. They are coded in the lower digits of the system schema indicator.

Xxx.0.0 no extention xxx.0. I heating ciruit

xxx. I.0 auxilary heating xxx. I. I auxilary heating and heating ciruit

xxx.2.0 circulation pump xxx.2. I circulation pump and heating ciruit

xxx.3.0 auxilary heating and circulation pump xxx.3. I aux. heating, circulation and heating ciruit

Example extentions of the basic system scheme I - I

System I - I.0. I

(with heating ciruit)

System I - I. I.0

(with auxilary heating)

System I - I. I. I

(with aux. heating and heating

6 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

Operation and display

Operating controls

Rotary pushbutton

Turn: Display, select parameters and function blocks

Push: Confirm adjusted selection or settings

Rotary switch – Operating modes

Control operation active, display of informations about the

operation of the controller (normal position - information level)

Control operation deactivated, frost protection is activated

(controller is still active)

Manual mode: Valves and pumps can be controlled manually.

Rotary switch – Parameter

Solar threshold on

Solar threshold off

Times-of-use and operating modes for:

heating circuit (1), auxilary heating (2) und circulation (3)

Party mode ... lets dance :-)

Setup of time, date and year

Configuration and parameter level

KA_37386_SOL3-5_EN001 7

Display

Rotary Switch Rotary

pushbutton

Quick installation and operating manual KT-Elektronik

Display

System scheme

The controller SOL3-5 it equipped with a graphical display. The display

allows it to visualize the current system scheme with all relevant sensor

informations as welll as state informations of pumps and valves for a

quick overview of the operating condition of the system.

Among the symbols used in the system scheme are the following:

Element Symbol Meaning

Pump

Pump is in operation

Pump is not in operation

Switching valve

Switching valve is showen with filled triangles

Valve

Valve is not in operation

Valve 'CLOSE' is in operation

Valve 'OPEN' is in operation

Auxilary heating

Auxilary heating is not in operation

Auxilary heating is in operation

Collector pump

A temporarily shown sun above a collector represents an operating state indication

of the pump belonging to the collector.

Condition for the activation of the pump is not met and the pump is not operating.

Condition for the activation of the pump is met and the pump is operating.

The condition for switching off the pump is met, but pump is due to the minimum ON

time still in operation.

Condition for switching on the pump is met, but pump is due to the minimum OFF

time yet in operation.

Operating mode

The operating modes of heating circuit, hot water circulation and auxilary

heating are in the system scheme, context-sensitive arranged and allow

capture at a glance the current function of the system part.

Operating mode Symbol Symbol Time phase

Standby Nominal operation

(Day mode)

Automatic mode Reduced operation

(Night mode)

Manual mode

8 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

Information level

At the normal rotary switch position ,„Information level“, the system scheme, time, date as well as relevant temperatures

measured by the connected sensors and state informations of pumps and valves of the selected hydraulc schema.

By turning and pushing the rotary pushbutton it is possible to show time, date, temperature, and query the values of

connected sensors and their setpoints.

Set rotary switch to Information level ;

Display: System schema and time

Turn rotary pushbutton;

Select value: In the display appears, depending on system configuration, successively the different

data points, which are described by an acronym:

Push rotary pushbutton;

Setpoint or limit value compared to the displayed value.

Pushing the rotary pushbutton in the clock display shows the date and year.

Sample displays Meaning

So: 14:57 Time

AF: -5.3°C Outdoor temperature AF

RF: 20.4°C Room temperature RF

VF: 34.1°C Temperature at flow sensor of heating circuit VF

SF1: 52.9°C Temperature at storage tank sensorr SF1

CF1: 27.3°C Temperature at collector sensor CF1

coll 12 h Operating hours of solar circiut

trend show Graphical presentation of logged system data

Setting the controller time

The current time and date must be set immediately after the commision

and after a power failure of more than 24 hours. In this case, the system

time on the clock 01/01/2000 10:00 preset and is displayed inverted (white

on black) .

Set rotary switch to time ;

Display: System scheme and time(inverted)

Turn rotary pushbutton;

Edit time, year or date

Push rotary pushbutton;

Confirm time, year or date

Display: year, date or time

Set rotary switch to Information level

KA_37386_SOL3-5_EN001 9

Quick installation and operating manual KT-Elektronik

Check and modify times-of-use

There are three independent sets of times-of-use for:

heating circuit, hot water circulation, auxilary heating.

For systems that do not contain the functional groups mentioned, this chapter

has no meaning, the display and input of times-of-use is not offered by the

SOL3-5.

Three times-of-use can be set for each day of the week. If only one time-of-use is

required, start and stop of second time-of-use must be equal.

Set rotary switch to times-of-use ;

Times-of-use for heating circiut is graphicaly shown, name of times-of-use is displayed inverted.

Turn rotary pushbutton: Select times-of-use (heating circuit, hot water circulation, auxilary heating)

Push rotary pushbutton: Confirm fo modify times-of-use - heating circuit

Day of week interval is shown inverted for the selection.

Turn rotary pushbutton: Select day of week (Monday to Sunday or single days)

Push rotary pushbutton: Confirm day of week or interval

Start of first time-of-use is shown inverted

Turn rotary pushbutton: Modify Start of first time-of-use

Push rotary pushbutton: Confirm Start of first time-of-use

Stop of first time-of-use is shown inverted

Turn rotary pushbutton: Modify Stop of first time-of-use

Push rotary pushbutton: Confirm Stop of first time-of-use; Modification of first time-of-use finished

Day of week interval is shown inverted for the selection.

Set rotary switch to Information level

Check and set party mode

Using the Party mode function, the controller continues or activates the day

mode during the time when the party timer is active, regardless of the

programmed times-of-use. The activation of the party mode (count down) starts

with turning the rotary switch to any operating mode position (e.g.information

level). When the party timer has elapsed, the party mode timer is reset to 00:00.

The party mode counts down in steps of 15 minutes and ranges up to 48 hours.

Set rotary switch to party mode stellen;

Times-of-use for heating circiut is graphicaly shown, name of times-of-use is displayed inverted.

Push rotary pushbutton: Confirm fo modify party timer - heating circuit

Party timer of heating circuit is in digits displayed inverted an graphicaly shown (black)

Turn rotary pushbutton: Modify party timer

Push rotary pushbutton: Confirm party timer

Set rotary switch to Information level

10 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

Setting the system code number (selection of the hydraulic scheme)

During the system choice the system scheme associated with the system code

number is displayed graphically, so the choice is possible using the concrete image.

The modification of the system code number resets the previously set function

blocks to the factory setting (FS). Function block parameters and settings in the

parameter levels will remain. The system code number is set in the configuration

level.

Set rotary switch to configuration and parameter level ;

Display: Settings menue (LCD contrast selected)

Turn rotary pushbutton: Select 'syst.var.id' in Settings menue (system code number)

Push rotary pushbutton: Confirm modification of system code number

Display: Access code (Key number)

Turn rotary pushbutton: Set valid key number

Push rotary pushbutton: Confirm key number

Display: System scheme and system code number inverted

Turn rotary pushbutton: Modify system code number

Push rotary pushbutton: Confirm system code number

Factory settings for the selected installation will be set automatically.

Display: Settings menue (system code number selected) – following system parameters can be

modified

Activating and deactivating funktions

A function is activated or deactivated in the associated function block.

In one configuration level up to 24 function blocks are available. To visualize the

function blocks in two rows of 12 squares are shown. From top left to bottom right of

the function blocks are shown number 1 to 24. Activated function blocks are marked

by a black square.

The function blocks are described in the installation and operating manual. This

document contains a list of functions.

The functions are grouped by topic:

CO1: Heating circiut (1) CO5: System-wide functions

CO3: Solar circuit CO6: Modbus communication

CO4: Auxilary heating / DHW circuit

Set rotary switch to configuration and parameter level ;

Display: Settings menue (LCD contrast selected)

Turn rotary pushbutton: Select 'CO3' in Settings menue

Push rotary pushbutton: Confirm entering configuration menue 'CO3'

Display: Access code (Key number)

Turn rotary pushbutton: Set valid key number

Push rotary pushbutton: Confirm key number

Display: Configuration menue 'CO3'

KA_37386_SOL3-5_EN001 11

Quick installation and operating manual KT-Elektronik

Turn rotary pushbutton: Select funktion to activate or deactivate function (1/0)

Push rotary pushbutton: Confirm selection

Function block 'F01 Forced pump op. 0' is shown

Turn rotary pushbutton:

Activate or deactivate function (1/0)

Push rotary pushbutton: Confirm activation or deactivation of function;

Function block parameter

Some functions that can be configured via function blocks require additional parameters. This

function block parameters can be queried to select or confirm a function block is activated in the line

of succession to the function block input or confirmation.

Turn rotary pushbutton:

select another function block to set or 'end' choose to leave the configuration level 'CO3'

Modify parameters

The parameters are grouped by topics:

PA1: Heating circuit (1) PA5: System-wide parameters

PA3: Solar circuit PA6: Modbus communication

PA4: Auxilary heating / DHW circuit

•

Set rotary switch to configuration and parameter level ;

Display: Settings menue (LCD contrast selected)

Turn rotary pushbutton: Select 'PA3' in Settings menue

Push rotary pushbutton: Confirm entering parameter menue 'PA3'

Display: Access code (Key number)

Turn rotary pushbutton: Set valid key number

Push rotary pushbutton: Confirm key number

Display: Parameter menue 'PA3'

Turn rotary pushbutton: Select parameter to modify

Push rotary pushbutton: Parameter value to modify is shown inverted

Turn rotary pushbutton: Set parameter

Push rotary pushbutton: Confirm parameter

Turn rotary pushbutton:

select another parameter to modify or 'end' choose to leave the configuration level 'PA3'

12 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

Resetting to default values

All parameters and function blocks set over the rotary switch as well as parameters in PA parameter levels and function

blocks in CO configuration levels can be reset to their default settings (factory default).

Set rotary switch to configuration and parameter level ;

Display: Settings menue (LCD contrast selected)

Turn rotary pushbutton: Select 'CO3' in Settings menue

Push rotary pushbutton: Confirm entering configuration menue 'CO3'

Display: Access code (Key number)

Turn rotary pushbutton: Set key number '1991'

Push rotary pushbutton: Confirm key number '1991

Save default settings (fd)

Important key numbers

I732

Common parameters and configuration

I999

Enhanced information level

I995

Modify key number for common parameters and configuration

I99 I

Load factory defaults

0025

Modify FSR error mask

00 I0

Modify data logging cycle

0002

Software reset

Manual mode

Im Handbetrieb erfolgt die Einstellung aller Ausgänge, siehe Anschlussplan

Set rotary switch to Manual mode

Display: System schema and 'collector 1'

Push rotary pushbutton:

Specification of the control value is displayd inverted

Turn rotary pushbutton:

Modify specification of the control value (OFF, ON , Auto)

Push rotary pushbutton:

Confirm specification of the control value

Turn rotary pushbutton:

Display: Designation control

To exit the manual mode, set the rotary switch to the Iinformation level is provided. The manual

mode positions are no longer valid. All outputs will to the set through the control function defined

value.

Display: Time

Note:

The outputs of the controller are not affected by simply turning the rotary switch to (manual level). You have to enter a

positioning value or activate/deactivate the pumps to configure the outputs.

The frost protection does not work during the controllers manual mode !

KA_37386_SOL3-5_EN001 13

Quick installation and operating manual KT-Elektronik

Function block lists

CO1: Heating circuit Rk1

F Function FD Comment

01 Room sensor RF1 0 CO1 -> F01 - 1: Temperature display activ

02 Outdoor sensor AF1 0 CO1 -> F02 - 1: Weather compensated control activ

05 Underfloor heating

Drying of jointless floors

0 CO1 -> F05 - 1: Limitation of the adjustment ranges; Function block parameters:

Start temperature / 20 to 60 °C (25 °C)

Temperatur rise per day / 1 to 10 °C/24 h (5 °C/24 h)

Maximum temperature / 25 to 60 °C (45 °C)

Maintaining time of max. temp. / 1 to 10 days (4 days)

Temperature reduction per day / 0 to 10 °C/ 24 h (0 °C/24 h)

START

07 Optimization 0 CO1 -> F07 - 1: only with

• CO1 -> F01 - 1

• CO1 -> F02 - 1

08 Adaptation 0 CO1 -> F08 - 1: only with

• CO1 -> F01 - 1

• CO1 -> F02 - 1

• CO1 -> F11 - 0

09 Flash adaptation 0 CO1 -> F09 - 1 only with CO1 -> F01 – 1; Function block parameters:

Cycle time / 0 or 1 to 100 min (20 min)

KP (gain) / 0 to 25 (0)

11 4-point characteristic 0 CO1 -> F11 - 1: 4-point characteristic, only with CO1 -> F08 - 0

CO1 -> F11 - 0: Gradient characteristic

12 Control mode 1 CO1 -> F12 - 1: three-step-control; Function block parameters:

KP (proportional gain) / 0,1 to 50,0 (2,0)

TN (reset time) / 1 to 999 s (120 s)

TV (derivative-action time) / 0 to 999 s (0 s;

TY (valve transit time) / 5, 10, 15, …, 240 s (45 s)

CO1 -> F12 - 0: On/Off-Controll; Function block parameters:

Hysteresis / 1 to 30 °C (5 °C)

min. ON time/ 0 to 10 min (2 min)

min. OFF time / 0 to 10 min (2 min)

13 Limitation of deviation for

OPEN signal

0 CO1 -> F13 - 1 only with CO1 -> F12 – 1; Function block parameters:

max. deviation / 2 to 10 °C (2 °C)

F Function block number, FD Factory default

CO3: Solar circuit

F Function FD Comment

01 Force automatic run (pump) 1 CO3 F01 = 1 - Force automatic run active

02 Collector frost protection 0 CO3 F02 = 1 - Collector frost protection active

03 Start function (Vakuum tube ) 0 CO3 F03 = 1 - Start function active

04 Speed conrol CO3 F04 = 1 Speed control active

05 Solar heat meter 0 CO3 F05 = 1 - Solar heat meter active

Function block parameters: thermal capacity at 25°C, thermal capacity at 100°C

06 Heat meter pulse source 0 CO3 F06 = 1 - Volume flow sensor active Function block parameters: Pulse ration

CO3 F06 = 0 - Volume flow replacement value active

Function block parameters: Volume flow replacement value

07 CVF 0 CO3 F07 = 1 - Collector flow sensor active

08 CRF 0 CO3 F08 = 1 - Collector return flow sensor active

09 CVF für CTP 0 CO3 F09 = 1 -Collector flow sensor active CVF for heat exchanger pump CTP active

10 Temperature difference

controller

10K

CO3 F10 = 1 Temperatur difference controller active

Function block parameter: Temperatur difference set point / -30 bis 160°C

Reference input / Terminal number 1...9

Controlled input / Terminal number 1...9

F Function block number, FD Factory default

14 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

CO4: DHW heating

F Function FD Comment

14 Thermal desinfection 0 CO4 -> F14 - 1 only with CO4 -> F01 - 1

Function block parameters:

Day of week / 1, 2, …, 7, 1–7 (3)

Start time / 00:00 to 23:45 (00:00)Stop time / 00:00 to 23:45 (04:00)

Desinfection temperature / 60 to 90 °C (70 °C)

Set point boost / 0 to 50 °C (10 °C)

F Function block number, FD , Factory default

CO5: System-wide functions

If CO5 F00 - 1 is indicated, access to the return flow, flow rate and heat capacity settings arelocked.

F Function FD Comment

Sensor initialisization 1 Irrelevant of the function block setting: Pt 1000

04 Summer mode 0 CO5 -> F04 - 1: Activation of time-controlled summer mode

Function block parameters:

Start summer mode / 01.01 to 31.12 (01.06)

No. of days until activation / 1 to 3 (2)

Stop summer mode / 01.01 to 31.12 (30.09)

No. of days until deactivation / 1 to 3 (1)

Outdoor temperature limit for summer mode / 0 to 30 °C (18 °C)

05 Delayed outdoor

temperature adaptation

when temperature

decreases

06 Delayed outdoor

temperature adaptation

when temperature increases

CO5 -> F05, 06 - 1: Function block parameters::

Delay per hour / 1 to 6 °C/h (3 °C/h)

08 Automatic summer / winter

time

09 Frost protection program II 1 CO5 -> F09 - 0: Frost protection program I (restricted Frostprotection)

Function block parameters:

Frost protection limit / –15 to 3 °C (3 °C)

CO5 -> F09 - 1: Frost protection program II

Function block parameters:

Frost protection limit / –15 to 3 °C (3 °C)

19 Temperature monitoring 0 CO5 -> F19 - 1: Temperature monitoring active

20 Sensor calibration 1 CO5 -> F20 - 1: Adjusting all sensor calibration values

CO5 -> F20 - 0: Deleting all adjusted sensor calibration values

21 Locking manual level 0

CO5 -> F21 - 1: In switch position (manual level) automatic mode applies

22 Locking the rotary switch 0 CO5 -> F22 - 1: 1: Rotary switch without function – Access after entering key number

still possible.

F Function block number, FD Factory default

CO6: Modbus

F Function FD Comment

01 Modbus 1 CO6 -> F01 - 1: Modbus active

02 Modbus-16-bit-adressing 0 Only with CO6 -> F01 – 1

CO6 -> F02 - 1: 16-bit-adressing,

CO6 -> F02 - 0: 8-bit-adressing

03 Modem function 0 CO6 -> F03 - 1 only with CO6 -> F01 – 1 and CO6 -> F08 - 1

04 Automatic modem

configuration

0 CO6 -> F04 - 1 only with CO6 -> F03 – 1and CO6 -> F08 - 1

05 Lock dial-upl 0 CO6 -> F05 - 1: No dial-up to GLT in case of error, only with CO6 -> F03 - 1

KA_37386_SOL3-5_EN001 15

Quick installation and operating manual KT-Elektronik

06 Dial-up also upon corrected

error

0 CO6 -> F06 - 1: 1: Dial-up to GLT also to indicate that an error has been corrected ,

only with CO6 -> F03 - 1

07 Control system monitoring CO6 -> F07 - 1: Resetting all level bits to “autonomous“ when there is no

communication, nur mit CO6 -> F01 - 1

08 Text message (SMS ) CO6 -> F08 - 1: Sending of text message active (SMS) active

F Function block number, FD Factory default

Parameter lists

PA1: Heating circuit

Nr. Symbol Descrition Range Factory defaults

PA1.01

Gradient, flow

with CO1 -> F05 - 1:

0,2 to 3,2

0,2 to 1,0

0,4

1,0

PA1.02

Level (parallel shift) –30 to 30 °C 0 °C

PA1.03 4-point-characteristic

1...4

Outdoor temperature –40 to 50 °C -15,-5,5,15°C

1...4

Flow temperature (Day mode) 5 to 130 °C 70,55,40,25°C

1...4

Flow temperature (Night mode) 5 to 130 °C 60,40,20,20°C

PA1.06

Min. flow temperature 5 to 130 °C 20 °C

PA1.07

Max. flow temperature

with CO1-> F05 - 1:

5 to 130 °C

5 to 50 °C

50 °C

PA1.08

Outdoor temp. deactivation value in rated operation 0 to 50 °C 22 °C

PA1.09

Outdoor temp. deactivation value in reduced operation –20 to 50 °C 15 °C

PA1.10

activation value in rated operation –20 to 5 °C –15 °C

PA1.11

Day set point for flow temp. 0 to 40 °C 20,0 °C

PA1.12

Night set point for flow temp. 0 to 40 °C 15,0 °C

PA3: Solar circuit

Nr. Symbol Descrition Range Factory defaults

PA3.01

Min. ON time collector pump 0 to 1800 s 60s

PA3.02

Min. OFF time collector pump 0 to 1800 s 180s

PA3.03

Max. storage tank 1 temperature switch OFF condition 50 to 160 °C 60°C

PA3.04

Max. storage tank 1 temperature switch ON condition 50 to 160 °C 58°C

PA3.05

Max. storage tank 2 temperature switch OFF condition 50 to 160 °C 60°C

16 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

PA3.06

Max. storage tank 2 temperature switch ON condition 50 to 160 °C 58°C

PA3.07

Mode of storage tank priority 1 to 5 3

PA3.08

Min. storage tank temperature for charging

Only in mode 2 of storage tank priority

5 to 90°C 30°C

PA3.09

Charging time for low-priority storage tank

Only in mode 3 of storage tank priority

0 to 120 min 15 min

PA3.10

Max. collector temperature switch OFF condition 90 to 160°C 130°C

PA3.11

Max. collector temperature switch ON condition 90 to 160°C 110°C

PA3.12

Min. collector temperature switch OFF condition -20 to 50°C 30°C

PA3.13

Min. collector temperature switch ON condition -20 to 50°C 35°C

PA3.14

Min. Switch ON time before change collector array 0 to 1800 s 60s

PA3.15

Switch-On delay collector / ext. heat exchanger pump 0 to 250 s 120 s

PA3.16

Follwow-up time collector / ext. heat exchanger pump 0 to 250 s 10 s

PA4: Auxilary heating – Storage tank temperature

Nr. Symbol Descrition Range Factory defaults

PA4.01

Day set point for storage tank temperature 5 to 90 °C 45 °C

PA4.02

Night set point for storage tank temperature 5 to 90 °C 10 °C

PA4.03

Hysteresis for storage tank temperature 0 to 30 °C 5 °C

PA4.04

Temperature difference to delay auxilary heating

When collector pump is active

0 to 20 °C 0 °C

PA5: System-wide parameters

Nr. Symbol Descrition Range Factory defaults

PA5.01

Public holidays 01.01 to 31.12

PA5.02

Vacation periods 01.01 to 31.12

PA6: Modbus communikation

Nr. Symbol Descrition Range

PA6.01

Stationsadresse 1 to 247

PA6.02

Stationsadresse (16-Bit) mit CO6.F02 - 1 1 to 32000

PA6.03

Modem cyclic initialisation ) 0 to 255 min

KA_37386_SOL3-5_EN001 17

Quick installation and operating manual KT-Elektronik

PA6.04

Modem dialing pause (P) 0 to 255 min

PA6.05

Modem time-out (T) 1 to 255 min

PA6.06

Number of redialing attempts to building control station (C) 1 to 255

PA6.07

Phone number of control station (TELnr) Max. 22 characters; 1, 2, 3,

…, 9, 0;

„-“ = end of a string

„P“ = pause

PA6.08

Access number (TAPnr)

PA6.09

Cell phone number

18 KA_37386_SOL3-5_EN001

KT-Elektronik SOL3-5

Technical specification

Inputs 9 inputs for Pt 1000 temperature sensors or binary input,

1 pulse input for calorimetry

1 input signal 0 bis 10 V (alternativly output signal 0-10V)

Outputs 5 relay outputs with varistor suppressor,

max. load 250 V AC, 2A (at cos φ= 1)

1 output signal 0 to 10 V (for speed control) (alternatively input 0-10V)

Optional interfaces 1 x Modbus interface (USB, RS-232, RS-485, LAN)

1 x interface for Datalogging module

1 x interface for Memory module

Operating voltage 85 to 250 V, 48 to 62 Hz, max. 3,5 VA

Ambient temperature 0 to 40 °C (operation),

–10 °C to 60 °C (storage and transport)

Degree of protection IP 40 according to IEC 529

Class of protection II according to VDE 0106

Degree of contamination 2 according to VDE 0110

Overvoltage category II according to VDE 0110

Humidity rating F according to VDE 40040

Noise immunity According to EN 61000-6-1

Noise emission According to EN 61000-6-3

Installation Panel mount, wall mount, top hat rail mount

Dimensions LxWxH (mm) 144 x 98 x 60

Weight Approx. 0,5 kg

Material

Mat.-Nr. Identification Despription

37386 SOL3-5 SOL3-5 Solar thermal and differential temperature controller

11982 USB-L3 USB-Communickation cable to connect SOL3 und WPR3 to USB (PC)

11988 KOM232PC Adapter to connect SOL3 and WPR3 to RS232 interface (PC)

11989 KOM232M Adapter to connect SOL3 and WPR3 to Modem (PSTN/GSM/ISDN)

11994 iCon485 Adapter to connect SOL3 and WPR3 to RS485 interface (Bus)

11991 DataMod11 Dial-up data modem for direct connection to telephone line (PSTN)

11993 ModTCP Modbus-TCP-Gateway

11997 ModBus-MBus ModBus-MBus Gateway

11996 CoRe01 Converter / Repeater for RS232 and/or RS485 interfaces

11998 SA5000 RS485 overvoltage protection module

11995 USB-CO3 RS485 / USB Converter 3, including software Datalogging-Viewer

37699 DataMEM Dataloging memory module for recording data, direct connection to controller

17090 ParaMEM Parameter memory module to transfer parameter and configuration data

37160 KT-Visual Remote control software KT-Visual

KA_37386_SOL3-5_EN001 19

KT-Elektronik GmbH

Berlinickestrasse 11

12165 Berlin

Telefon: (030) 79 08 05-0

Telefax: (030) 79 08 05-20

e-mail: [email protected]

Internet: http://www.kt-elektronik.de

KA_37386_SOL3-5_EN001

08/2011

KT-Elektronik SOL3-5 Quick Installation And Operating Manual

Brand: KT-Elektronik

Model: SOL3-5

Type: Quick Installation And Operating Manual

This manual is also suitable for

SOL3-7

Download PDF

report

KT-Elektronik SOL3-5 Quick Installation And Operating Manual

This manual is also suitable for

KT-Elektronik SOL3-5 Quick Installation And Operating Manual

Related papers

Other documents