Sterling Roll-In Shower 62060103 Specification

Type
Specification

This manual is also suitable for

Features
Compression molded from our exclusive solid Vikrell
®
material
Factory installed stainless steel grab bars
Engineered for ease of installation
Durable swirl-gloss finish
10-year consumer/3-year commercial limited warranty
Tongue-and-groove 4-piece modular design allows for
easy snap together installation
1/2 (13 mm) low profile threshold for easy
wheelchair access
63-1/2 (1613 mm) x 40-5/8 (1032 mm) x 73-1/4
(1861 mm) direct-to-stud rough-in, including flange
63-1/4 (1607 mm) x 39-3/8 (1000 mm) x 72 (1829
mm) complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
ADA
ICC/ANSI A117.1
HUD, UM Bulletin 73A
NAHB Research Foundation, Inc.
ASTM E162
ASTM E662
ANSI Z124.1.2
63 (1600 mm) ADA COMPLIANT
ROLL-IN SHOWER
62060103
Colors/Finishes
0: White
Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Description Colors/Finishes
62060103 63 (1600 mm) ADA compliant* shower receptor and wall
surround, with grab bars
0 Other_____
*Product is shipped as ADA compliant with factory assembled grabs bars. When properly installed, the complete
installation is ADA compliant. Components are also available separately but are provided only as ADA adaptable.
Page 1 of 2
1016221-4-
G
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING
Installation Notes
Install this product according to the installation guide.
Drain cutout in subfloor to be 10-1/2 (267 mm) per rough-in
illustration below to allow the backside of the drain to sit
below the subfloor surface.
Studs should be positioned as shown.
Backer boards and fasteners protrude beyond the back wall
1-1/2 (38 mm). If installing this product against wall board,
1-1/2 (38 mm) furring strips installed over the wall board are
recommended. The stud pocket depth of 40-5/8 (1032 mm)
will need to be increased by the combined thickness of the
wall board and furring strips.
39-3/8"
(1000 mm)
1" (25 mm)
63-3/8" (1610 mm) Min
63-1/2" (1613 mm) Max
31-5/8"
(803 mm)
Ø 3-5/16"
(84 mm)
Drain Hole
Ø 10-1/2"
(267 mm)
Drain Cutout
18-3/4"
(476 mm)
4"
(102 mm)
13"
(330 mm)
8"
(203 mm)
29"
(737 mm)
40-5/8"
(1072 mm) Max
16"
(406 mm)
15-3/4"
(400 mm)
16"
(406 mm)
63-5/16"
(1608 mm)
1-1/4"
(32 mm)
73-9/16"
(1868 mm)
8" (203 mm)
39-3/8"
(1000 mm)
63-1/4"
(1607 mm)
33"
(838 mm)
72"
(1829 mm)
73-1/4"
(1861 mm)
Product Diagram
63 (1600 mm) ADA COMPLIANT ROLL-IN SHOWER
Page2of2
1016221-4-
G
  • Page 1 1
  • Page 2 2

Sterling Roll-In Shower 62060103 Specification

Type
Specification
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI