Home Styles 5524-69 Operating instructions

Brand: Home Styles

Model: 5524-69

Type: Operating instructions

Part List

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damages occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure

a completed product as it was designed.

Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319

[email protected]

88 5524 691

Pantry

For assembly see instructions in carton 88 5524 692

Side Panel

1 pc.

Door

2 pcs.

Door

2 pcs.

Side Panel

1 pc.

Side Panel

1 pc.

Side Panel

1 pc.

Part List

Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319

[email protected]

Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level

Hardware List

Hex Wrench

1 pc.

Small

Hex Wrench

1 pc.

M4x45

Machine Screw

4 pcs.

Cam Lock Screw

28 pcs.(+2 extra)

Cam Lock

28 pcs.(+6 extra)

Adjustable Pin

16 pcs. (+1 extra)

M3x15

Wood Screw

for Magnet

8 pcs. (+1 extra)

Knob

4 pcs.

Also need the following from carton 88 5524 691

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damages occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure

a completed product as it was designed.

88 5524 692

Pantry

Back Stretcher

4 pcs.

Shelf

4 pcs.

Top

1 pc.

Bottom

1 pc.

Back Piece

1 pc.

Back Panel

2 pcs.

Back Piece

1 pc.

Back Panel

2 pcs.

Top

1 pc.

Bottom

1 pc.

Magnet

2 pcs.

Steel Plate

Connector

2 pcs.

M3.5x16

Wood Screw

20 pcs. (+1 extra)

Assembly Instructions 2/6

IMPORTANT

* Do not tighten up all the screws until each part is properly assembled.

* You should keep Hex Wrench in a safe place as you may need to tighten up the Cam Locks in the future.

* Use a soft cloth between these parts and the floor.

* After assembly, item must be level to work properly. Use the included adjustable levelers to level.

Figure 2

Figure 1

STEP 2

Put Cam Lock Screws into the

pre-drilled holes of Tops (G), (O)

and tighten.

Attach Magnets to Tops (G) and

(O) with Wood Screws for Magnet.

(see Figure 2)

STEP 1

Put Cam Lock Screws into the pre-drilled holes

of Side Panels (C), (D), (E), (F) and Bottoms (H), (P) and tighten.

(see Figure 1)

Cam Lock Screw

Wood Screw for Magnet

Magnet

Cam Lock Screw

Assembly Instructions 3/6

Figure 3

STEP 3

Attach Back Piece (K) to Back

Stretchers (J).

Slide Back Panels (L) into position.

Attach Side Panels (C) and (D) to unit

with Cam Locks. (See Figure 3)

Attach the unit to Bottom (H) with Cam

Locks.

STEP 4

Attach Doors (A) and (B) to unit by sliding

the door lift hinges into the side panel lift

hinges. (see Figure 4)

Attach Top (G) to unit with Cam Locks.

Assemble Knobs to Doors

(A) and (B) with Machine Screws.

(see Figure 5)

Cam Lock

Figure 5

Figure 4

Assembly Instructions 4/6

STEP 5

Attach Back Piece (M) to Back

Stretchers (J).

Slide Back Panels (N) into position.

Attach Side Panels (E) and (F) to unit

with Cam Locks.

Attach the unit to Bottom (P) with Cam

Locks.

Cam Lock

STEP 6

Attach Doors (A) and (B) to unit by sliding

the door lift hinges into the side panel lift

hinges.

Attach Top (O) to unit with Cam Locks.

Assemble Knobs to Doors

(A) and (B) with Machine Screws.

Assembly Instructions 5/6

STEP 7

Place the top unit onto the base unit.

Insert the Adjustable Pins into the

side panels at the desired level.

Place Shelves (I) into position.

STEP 8

To level the unit, adjust the adjustable

levelers on the bottom of unit. (see Figure 6)

Insert Wood Screws from the back

of the unit and tighten.

Note: Unit must be level before tightening these screws.

Attach Steel Plate Connectors with Wood Screws.

(see Figure 7)

Steel Plate Connector

Adjustable Pin

Figure 7

Figure 6

Wood Screw

Wall Screw

M3.5x16

Wood Screw

1 pc.(+1 extra)

Anchor

1 pc.(+1 extra)

Bracket

2 pcs.(+1 extra)

Tipover Restraint

1 pc.(+1 extra)

Hardware List

Drill 3/8” hole in wall

Top of unit

Attention!

To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust

these instructions exactly!

M3.5x40

Wall Screw

1 pc.(+1 extra)

tie end

loop end

Place unit at desired location.

Drill a hole in wall3/8”

at the appropriate location.

Insert Anchor into the wall hole

and attach Bracket with Wall Screw.

Attach Bracket at pre-drilled hole at top

of unit with Wood Screw.

Use Tipover Restraint to secure Bracket

on unit to Bracket on wall.

(see Figure X)

Put tie end of Tipover Restraint into loop end

of Tipover Restraint and pull until tight.

Figure X

Assembly Instructions 6/6

Bracket

on wall

Anchor in wall

3/8” wall hole

Bracket at

top of unit

Tipover

Restraint

Home Styles 5524-69 Operating instructions

Home Styles 5524-69 Operating instructions

Home Styles 5524-69 Operating instructions

Related papers

Other documents