EZ-FLO 10687 Installation guide

EZ-FLO
Brand
EZ-FLO
Model
10687
Category
Sanitary ware
Type
Installation guide
Single Control
Kitchen Faucet
With Pull Down Spray
Before You Begin
Check to make sure you have the following:
10687
Tools and Supplies
You will need the following to install your new faucet:
Adjustable
Wrench
Phillips
Screwdriver
Silicone
Sealant
Shut off main water supply before installation.
Faucet Installation
2 Check for proper thickness of sink. 3a With deck plate installation: Place a bead of
clear silicone sealant (not included) around the
base of the putty plate. Place the putty plate and
the deck plate on the sink. Rotate the two
half-moon locking nuts inward, then insert the
top mounting fixture into the sink.
3b Without deck plate installation:
Rotate the two half-moon locking nuts
inward, then insert the top mounting
fixture into the sink.
5 Insert water supply lines one by
one through the large hole of the top
mounting fixture.
6 Align arrow on faucet body with arrow
on top mounting fixture. Attach faucet
body to top mounting fixture and turn
counter-clockwise. Make sure there is no
gap, then tighten the set screw with the
hex wrench.
Ø1 3/8”~Ø1 1/2”
(Ø35mm~Ø38mm)
1/16”~1 1/2”
(1mm~38.1mm)
Cold Line
Hot Line
Ø1 3/8”~Ø1 1/2”
(Ø35mm~Ø38mm)
1/16”~1”
(1mm~25.4mm)
Ø1 3/8”~Ø1 1/2”
(Ø35mm~Ø38mm)
1/16”~1”
(1mm~25.4mm)
(a)
Ø1 3/8”~Ø1 1/2”
(Ø35mm~Ø38mm)
1/16”~1 1/2”
(1mm~38.1mm)
(a)
7 Identify hot and cold water supply
valves below sink. Connect and tighten the
water supply line nuts by using two
adjustable wrenches (avoid twisting or
kinking).
Red Line
Blue Line
Cold
Hot
8 Remove spray head from hose.
Turn on water and allow water to run
through the hose to flush out the
faucet. Check for leaks.
Hot
Open
Cool
1 Shut off water supply.
4 The word “FRNT” on the top
mounting fixture must face the front of the
sink. Secure the top mounting fixture in
place with the provided hex wrench and
screw the locking nuts clockwise.
9 Replace spray head.
Faucet Installation
1 Screw & Plug A66D558
2 Metal Handle A662358-T
3 Handle Trim Cap A103062
4 Locking Nut A104072
5 Ceramic Disc Cartridge A507348N
6 Screw A008003
7 Spray Head A528014N
8 Cover Plate Assembly A667003
9 Top Mounting Fixture A521000
10 Hex Wrench (H2.5mm * 45mm L * 70mm L) A031011NI
11 Hex Wrench (H2.5mm * 11mm L * 53mm L) A031217NI
Keep this manual for ordering replacement parts.
Replacement Parts
Minor problems often can be fixed without a plumber. Before doing any work on the faucet, shut off water supply and
close stopper or drain to avoid losing small parts.
noituloSesuaCmelborP
Troubleshooting Guide
Locking nut has come loose. O-ring
on cartridge is dirty or damaged.
Tighten the locking nut. Clean or
replace O-ring.
Leaks underneath handle.
3.
1.
4.
5.
6.
8.
7.
11.
10.
2.
9.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

EZ-FLO 10687 Installation guide

EZ-FLO
Brand
EZ-FLO
Model
10687
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents