OWNER’SMANUAL
MPN(s): PLTRAINER1-PLTRAINER2
SKU(s): 400868
UPC(s): 840009205927
2
P A R T S D I A G R A M / E X P L O D E D V I E W
3
KEY
BOX
DESCRIPTION
QTY
KEY
BOX
DESCRIPTION
QTY
(1)
2
Base Frame
1
(38)
2
Shock Absorber RubberΦ77*Φ47.5*13
4
(2)
2
Middle Base Frame
1
(39)
2
End Cap Φ48*2
4
(3)
2
Front Base Frame
1
(40)
2
End Cap □50*2
4
(4)
2
Right Base Frame
1
(41)
2
Pulley Spacer Bush
8
(5)
2
Left Base Frame
1
(42)
2
Front Pipe Sleeve
4
(6)
1
Upright Frame
2
(43)
2
Rubber Sleeve
8
(7)
2
Top Cross Frame
1
(44)
2
End Cap Φ25*2.5
2
(8)
1
Middle Upright Frame
1
(45)
2
12 Section Chains
1
(9)
1
Guide Rod
2
(46)
2
Hook Φ8*80
5
(10)
1
Right Cross Frame
1
(47)
2
Clip Φ50*Φ5
2
(11)
1
Left Cross Frame
1
(48)
2
Triceps Rope
1
(12)
2
Handle Bar Frame
1
(49)
2
Ankle Strap
1
(13)
2
Right Sliding Frame
1
(50)
2
Rubber Foot
2
(14)
2
Left Sliding Frame
1
(51)
2
Shock Absorber RubberΦ55*Φ25*25
2
(15)
1
Heighten Frame
2
(52)
2
Sliding Sleeve
4
(16)
2
Bar Plate Holder
1
(53)
2
□50 horseshoe Sleeve
4
(17)
2
Fixing Frame
1
(54)
2
Handle Grip
2
(18)
2
Pedal Frame
2
(55)
2
Bushing
4
(19)
2
Small Hook
4
(56)
2
Hex BoltM8*12
6
(20)
2
Upright Bar Plate Holder
2
(57)
2
Hex Bolt M10*20
4
(21)
2
Long Pulley Plate
2
(58)
2
Hex Bolt M10*25
4
(22)
2
Spacer Bush
2
(59)
2
Hex Bolt M10*35
5
(23)
2
Three Pulley Fixing Plate
1
(60)
2
Hex Bolt M10*45
19
(24)
2
Pulley Frame
1
(61)
2
Hex Bolt M10*65
4
(25)
2
Dual Pulley Frame
2
(62)
2
Hex Bolt M10*70
18
(26)
1
Small Handle
1
(63)
2
Hex Bolt M10*75
16
(27)
1
Long Handle
1
(64)
2
Hex Bolt M12*110
2
(28)
2
Upper Cable Combination
1
(65)
2
Cross Recess Pan Head Bolt M5*10
4
(29)
2
Lower Cable Combination
1
(66)
2
Hex Socket Head BoltM6*15
8
(30)
2
Cable Combination
1
(67)
2
Flat Washer Φ9*Φ16*1.6
6
(31)
2
Pin Combination
2
(68)
2
Flat Washer Φ11*Φ20*2
108
(32)
2
Handle Grip
2
(69)
2
Flat Washer Φ10.5*Φ30*2.5
14
(33)
2
Handle Grip
2
(70)
2
Flat Washer Φ13.5*Φ24*2.5
4
(34)
2
Hollow Sleeve
4
(71)
2
Spring Washer Φ10
4
(35)
2
Φ95 Pulley
30
(72)
2
Nut M10
62
(36)
2
Φ50 Pulley
1
(73)
2
Nut M12
2
(37)
2
Shock Absorber RubberΦ55*Φ26*5
2
(74)
2
Thin Nut M12
1
4
A S S E M B L Y I N S T R U C T I O N S
Step 1
Install the Guide Rod(9) to Base Frame (1), using Hex Bolt M10*25 (58).
Assemble the Base Frame (1) , Middle Base Frame (2)and Front Base Frame (3) using Flat Washer Φ11*Φ20*2
(68) , Flat Washer Φ10.5*Φ30*2.5 (69) ,Nut M10 (72)and Hex Bolt M10*70 (62).
Please tighten all bolts.
5
Step 2
Connect Right Base Frame(4), Left Base Frame(5), Middle Base Frame (2)and Front Base Frame (3), using Flat
Washer Φ11*Φ20*2 (68) , Flat Washer Φ10.5*Φ30*2.5 (69) ,Nut M10 (72), Hex Bolt M10*70 (62) and Hex
Bolt M10*75 (63).
Please tighten all the bolts .
6
Step 3
1. Install Middle Upright Frame (8) on the Middle Base Frame (2), using Flat Washer Φ11*Φ20*2 (68),Nut M10 (72)
and Hex Bolt M10*75 (63).
2. Put the Shock Absorber Rubber (37) ,Heighten Frame (15) ,Shock Absorber Rubber (51) and Bar Plate
Holder on the Guide Rod (9) .Then assemble the Pulley Frame (24) on Bar Plate Holder(16).Tighten the Nut.
7
Step 4
1. Assemble the Top Cross Frame (7) on Middle Upright Frame(8) and Guide Rod(9), using Flat Washer Φ
11*Φ20*2 (68),Nut M10 (72) , Hex Bolt M8*25 (58) and Hex Bolt M10*75 (63).
2. Install the Fixing Frame (17) on the Handle Bar Frame (12) using Flat Washer Φ9*Φ16*1.6 (67) and Hex
Bolt M8*12 (56).
3. Install the Handle Bar Frame (12) on the Top Cross Frame (7) using Flat Washer Φ11*Φ20*2 (68) , Flat
Washer Φ10.5*Φ30*2.5 (69) ,Nut M10 (72), and Hex Bolt M10*70 (62).
Step 5
8
Install Right Cross Frame(10), Left Cross Frame(11) on Top Cross Frame (7) and Handle Bar Frame (12) , using
Flat Washer Φ11*Φ20*2 (68) , Flat Washer Φ10.5*Φ30*2.5 (69) ,Nut M10 (72), Hex Bolt M10*70 (62) and
Hex Bolt M10*75 (63).
Step 6
9
1. Put the Right Sliding Frame(13) and Left Sliding Frame(14) on Upright Frame(6).
2. Install the Upright Frame(6) on Right&Left Base Frame(4&5) and Right&Left Cross Frame(10&11), using
Flat Washer Φ11*Φ20*2 (68),Nut M10 (72) and Hex Bolt M10*75 (63).
3. Fixing the Rubber Sleeve(43) on Upright Frame (6) using Hex Socket Head Bolt M6*15(66).
Please tighten all the bolts and nuts.
Step 7
10
1. Install the J-Hook(19) on the Middle Upright Frame (8) using Flat Washer Φ9*Φ16*1.6 (67) and Hex Bolt
M8*12 (56).
2. Install the Upright Bar Plate Holder(20) on Right& Left Base Frame(4&5) using Flat Washer Φ11*Φ20*2
(68) , Nut M10 (72), and Hex Bolt M10*70 (62).
3. Install the Pedal Frame(18) on Front Base Frame(3) using Flat Washer Φ11*Φ20*2 (68) , Spring Washer Φ
10 (71) , and Hex Bolt M10*20 (57).
Please tighten all the bolts and nuts.
Step 8
11
1. Fixing the pulley(35) on the Top Cross Frame (7) using Pulley Spacer Bush(41), Flat Washer Φ11*Φ20*2
(68),Nut M10 (72), Hex Bolt M10*45 (60), Hex Bolt M10*65 (61) and Hex Bolt M10*75 (63).
2. Remove the Fixing frame(Z), Washer(Y) and Stopper(X) from the Upper cable(28),then through each
pulley(A)(B)(C)(D)(E)(F)(G)(H)(G)(F)(E)(D)(C)(J)(K) in turn as drawing, and the stopper (X), Washer(Y) and
Fixing frame(Z), using Flat Washer Φ11*Φ20*2 (68),Nut M10 (72) and Hex Bolt M10*35 (59).
Please tighten all the bolts and nuts.
Step 9
12
1. Fixing the pulley(35&36) on the Base Frame using Flat Washer Φ11*Φ20*2 (68),Nut M10 (72) and Hex
Bolt M10*45 (60).
2. The Lower Cable(29) through each pulley(L)(M)(N)(O)(P) in turn as drawing, then fixing by Flat Washer
Φ11*Φ20*2 (68),Nut M10 (72) and Hex Bolt M10*35 (59).
Please tighten all the bolts and nuts.
Step 10
1. Fixing the pulley(35) on the Cross Frame ,using Pulley Spacer Bush(41), Flat Washer Φ11*Φ20*2
(68),Nut M10 (72), Hex Bolt M10*45 (60) and Hex Bolt M10*65 (61).
13
2. Remove the Fixing frame(Z), Washer(Y) and Stopper(X) from the cable(30),then through each
pulley(R)(S)(T)(U)(V)(W) in turn as drawing, and the stopper (X), Washer(Y) and Fixing frame(Z), using
Flat Washer Φ11*Φ20*2 (68),Nut M10 (72) and Hex Bolt M10*35 (59).
Please tighten all the bolts and nuts.
Step 11
Install all Accessories on the Machine.
14
15
This concludes the PLTRAINER Owner’s Manual.
If applicable to your product, make sure to tighten all nut-
and-bolt combinations before use.
Enjoy!
DISCLAIMER
This equipment must be used with care by capable and competent individuals under supervision, if necessary.
The use of any fitness equipment, including this one, involves the potential risk of injury. You accept and assume full
responsibility for any and all injuries, damages (both economic and non-economic), and losses of any type, which may
occur, and you fully and forever release and discharge Titan, its insurers, employees, officers, directors, associates, and
agents from any and all claims, demands, damages, rights of action, or causes of action, present or future, whether the
same be known or unknown, anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
TITAN MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE EQUIPMENT, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, WHETHER EXPRESS OR IMPLIED BY LAW,
COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. BUYER ASSUMES ALL LIABILITY IN
USE OF THE EQUIPMENT.
NEED HELP?
CONTACT US FIRST.
1 (800) 605-8241
info@titandistributorsinc.com/www.titan.fitness
Business Hours: Monday–Friday • 8:00 a.m.–5:00 p.m. (CT)
/
