Stinger R-GM14H User manual

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 1

Rev: V1

Date: 030121

®

Introduction and Features

The SR-GM14H is a complete radio replacement kit for the installation of the Stinger HEIGH10® modular radio in Chevrolet

Silverado and GMC Sierra trucks. All modules, cables and adapters are included to retain important features of the factory system,

including: OnStar, front and rear park assist, warning chimes, factory reverse camera, steering wheel-mounted radio controls and

AM/FM reception. Plug & Play wiring harnesses allow for quick and easy installation without the need to cut or splice any wiring.

The display mounting panel allows ush mounting the 10 inch display without modifying/cutting any part of the vehicle’s sub-dash.

Important Notes

Recommended Tools

We recommend reading this manual thoroughly to familiarize yourself

with the entire process prior to beginning the installation.

1. HEIGH10 Display Mounting Panel

2. Dual USB Extension (SSUSB2)

3. AM / FM Antenna Adapter (BAA22)

4. Satellite Antenna Adapter (SAT-01)

5. Main Harness (SR-GM14H-HAR-A)

6. Vehicle Side Harness B (SR-GM14H-HAR-B)

7. Vehicle Side Harness C (SR-GM14H-HAR-C)

8. Radio Replacement Interface (RP5-GM51)

9. Steering Wheel Control Harness (GM5LIN-SW-HAR)

10. Factory Rear Camera Adapter (CAM-GM51)

11. IOB Display Harness (GM5CAM-DIS-HAR)

12. Chime Module (CMX)

13. Dierential Video Adapter (RPA-VA1)

Included Components

1

4

6

10

8

5

211

3

7

9

12

13

1. Does not retain the following factory features:

2. Not compatible with vehicles equipped with Bose amplied audio system.

3. Please make your vehicle settings selections before removing the factory radio for optimal installation time. Once the radio

has been removed, the vehicle settings which are normally selected through the factory radio can be accessed and changed

by downloading and installing the PAC Vehicle Settings program from http://www.pac-audio.com/rmware

4. The Voice button can be set to activate the factory OnStar function when pressed for longer than 1.5 seconds or given

the ability to control the aftermarket radio. This option can be found in the PAC Vehicle Settings program mentioned above in

note three. The default setting for this button is to control the factory OnStar. If this button is set to control the aftermarket radio,

OnStar can still be accessed by using the mirror controls.

● Factory satellite radio

● Rear seat entertainment system (RSE)

● Steering wheel control backlighting

● Factory USB Ports

Plastic Panel Tool

7mm Socket

10mm Socket

Pick Tool

Wire Feeder

Ratchet

Torx T15 Screwdriver

Small Flat-blade Screwdriver

NOTE: Along with the SR-GM14H components,

additional hardware and wire harnesses from the

HEIGH10 (UN1810) kit will also be used in the

installation.

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 2

Rev: V1

Date: 030121

®

GPS

UN1810

USB1 USB2

STINGER

BLACK

GRAY

10PIN6PIN

24PIN 16PINGPS AM/FM

ANT.

Stinger

Connection

Main Harness

Connection Connections shown are

all required for full

functionality of the kit

and radio. If adding

additional components,

additional connections

will be needed.

Connects to

SXV300 Satellite

Radio Tuner

(sold separately)

REVERSE CAM

A/V IN

RPA-VA1

REVERSE CAM

AUX

16PIN RADIO

6PIN RADIO

SWI

CAM GM51 INPUT

SWC INPUT

CMX

chime module

OR

SR-GM14H-HAR-B

SR-GM14H-HAR-A

SR-GM14H-HAR-B

CAM-GM51-HAR

GM5LIN-SW-HAR

CMX CHIME

RP5-GM51

Wiring Overview

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 3

Rev: V1

Date: 030121

®

Before starting, determine the vehicle’s factory audio system by

referencing the Service Parts Identication sticker inside the

upper glove box.

The installations are very similar for each type of factory audio

system, but there are dierences referenced throughout this guide.

Note: The installation shown in this guide is IO5 with factory

rear camera and steering wheel controls.

One of these RPO codes will be listed:

IO3, IO4, IO5, IO6 or IOB

Step 3Step 2

Step 1

Section 1: Disassembly

Part One: Center Dash Disassembly

If equipped, remove the two

7mm screws from the CD/DVD

mechanism, remove and unplug.

(This plug will not be reconnected).

Remove the four 7mm screws

securing the radio display/climate

control panel. Pull outward to

release the retaining clips.

Remove all connectors from the

back of the panel.

Remove the radio display/climate

control trim panel using a plastic

trim tool to release the retaining

clips. Unplug any wire harnesses

from the back of the trim panel, if

equipped.

This installation manual will cover the necessary order of procedures to complete the installation

eciently and to avoid redoing any steps. The order will be as follows; Disassembly, In-Vehicle Harness

Connections and Preparation, Interface and Main Harness Connections, Display Mounting Panel

Preparation, Radio Module Preparation and Radio Unit Installation.

The installation steps shown are all required for full functionality of the radio. If adding additional

components; cameras, ampliers, satellite radio, etc., additional steps and harnesses will be needed.

Factory Radio Code

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 4

Rev: V1

Date: 030121

®

Step 4

Part One: Center Dash Disassembly (cont.)

Remove the three 7mm screws

securing the air vent on the left

side of the radio opening and

remove the vent.

Step 3

Step 2

Step 1

Using a panel tool or similar,

release the top retaining clips and

remove the storage assembly.

Remove the upper Torx T15

screw inside the storage

compartment.

Remove the two Torx T15 screws

from the bottom edge of the

storage compartment.

Part Two: Lower Storage Compartment Removal

Section 1: Disassembly (cont.)

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 5

Rev: V1

Date: 030121

®

Step 3

Step 6

Step 2

Step 5

Step 1

Step 4

Section 1: Disassembly (cont.)

Part Three: Glove Box Removal (Optional)

Pull outward on the lower glove

box to release the retaining clips

and remove the lower glove box.

Unplug the gray 12 pin camera

harness from the HMI module.

Open the upper and lower glove

box doors and remove the two

Torx T15 screws securing the

lower glove box.

Up, behind the metal bar running

across the inner dash, locate the

HMI Module; black module with

multiple colored plugs facing down.

Remove the two Torx T15 screws

from the bottom edge of the lower

glove box.

Remove the two Torx T15 screws

and pull to remove the upper

glove box. Unplug the factory USB

port from the backside.

If the vehicle is equipped with IO4, IO5 or IO6 radio AND a factory rear camera, follow the steps below to

remove the glove box. For IO3 and IOB vehicles, or no factory rear camera, proceed to Part Four.

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 6

Rev: V1

Date: 030121

®

Part Four: A Pillar Removal

Step 3

Step 2

Step 1

Pull the trim panel to release the

retaining clips and remove.

Remove the two 10mm bolts.

Remove the inserts covering the

bolts on the passenger A pillar

handle.

Part Five: Lower Steering Column Cover Removal (Optional)

Step 3

Step 2

Pull downward on the lower

cover on both sides to release

the locking tabs and remove the

lower cover.

Remove the plastic handle from

the steering wheel tilt lever by

pulling outward, towards the

driver’s door on the handle. A trim

tool may also be used if unable to

remove by hand.

If the vehicle is equipped with IO3, IO4, IO5 or IO6 radio AND steering wheel controls, follow the steps

below to remove the lower steering column cover. For IOB vehicles or no steering wheel controls, proceed

to Section Two on next page.

Step 1

Remove the two Torx T15 screws

from the bottom edge of knee

panel below the steering column.

Pull outward to remove the panel

and lay carefully on the oor board.

Section 1: Disassembly (cont.)

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 7

Rev: V1

Date: 030121

®

Step 3Step 2

Step 1

Step 4

Install the optional USB cover and

feed the USB cables through the

front of the panel. Secure with the

anged nut and then lock with the

lock nut.

Remove the plastic sleeve by

depressing the two tabs and

pushing out the front.

From the backside of the lower

storage compartment, remove the

metal insert from the power outlet

by releasing the two retaining clips

with a small pick and pushing out

the front side.

Route the USB cables up and out

of the right side opening at the

rear of the CD/DVD opening.

Section 2: In-Vehicle Harness Connections and Preparation

Part One: Dual USB Extension (SSUSB2)

Apple CarPlay, Android Auto, and any Firmware Updates require access to a USB port. The SSUSB2 is designed to extend the

USB ports on the back of the HEIGH10 to where they are accessible once the radio is installed.

For this installation, the factory 12V power outlet will be replaced with the SSUSB2. You may chose to follow these steps, or

mount the USB port somewhere else in the vehicle. Please note, the factory USB ports will no longer function after the factory

radio is removed.

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 8

Rev: V1

Date: 030121

®

Step 3

Step 2

Step 1

Route the camera RCA out of the

left side opening at the rear of the

CD/DVD opening.

Secure the T-harness to the factory

wire harness. Route the 50” single

lead from the GM5LIN-SW-HAR to

the radio opening, securing with zip

ties.

Route the yellow RCA end of

the camera cable to the radio

opening. Secure plug and cable

with zip ties.

Plug the male connector into the

female end of the GM5LIN-SW-

HAR and plug the GM5LIN-SW-

HAR male end into the female

connector on the steering column.

Plug the gray 12 pin camera

harness from the HMI module into

the CAM-GM51-HAR.

Locate and unplug the black 10

pin connector located on the

underside of the steering column.

Section 2: In-Vehicle Harness Connections and Preparation (cont.)

Part Two: Factory Rear Camera Retention Harness (CAM-GM51-HAR)

Part Three: Steering Wheel Control (SWC) Retention Harness (GM5LIN-SW-HAR)

If the vehicle is equipped with IO4, IO5 or IO6 radio AND a factory rear camera, follow the steps below to

install the factory camera retention harness behind the glove box. For IO3 and IOB vehicles, or no factory

rear camera, proceed to Part Four.

If the vehicle is equipped with IO4, IO5 or IO6 radio AND steering wheel controls, follow the steps below to

install the SWC retention harness at the steering column. For IO3 and IOB vehicles, or no steering wheel

controls, proceed to Part Four.

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 9

Rev: V1

Date: 030121

®

Step 1 Step 2 Step 3

Step 4

Route the steering wheel control

lead into the CD/DVD area

through the left side opening in the

rear of the cavity.

Part Three: Steering Wheel Control (SWC) Retention Harness (cont.)

Part Four: GPS Antenna

The GPS antenna is required for proper operation of Apple CarPlay and Android Auto, in addition to the optional GPS if

installed. The GPS antenna is included in the HEIGH10 hardware.

Section 2: In-Vehicle Harness Connections and Preparation (cont.)

Continue routing the GPS cable

across the inner dash towards the

radio opening securing with zip ties.

Position the GPS antenna and

route the antenna cable down

into the glove box area. Replace

the A pillar panel and ensure the

cable does not interfere or get

pinched.

Route the GPS cable into the CD/

DVD area through the right side

opening at the rear of the cavity.

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 10

Rev: V1

Date: 030121

®

Step 2 Step 3

Step 1

Unplug the Black antenna cable

from the factory tuner and re-route

it down and through the right side

opening of the lower CD/DVD area.

Connect the BAA22 Antenna

adapter to the factory antenna.

Unplug the Green and Gray

or Mustard and Gray (IOB)

connectors from the factory tuner

and re-route them down and

through the left opening of the

lower CD/DVD area.

Part Five: Vehicle Side Plug Relocation and Antenna Adapter

Section 2: In-Vehicle Harness Connections and Preparation (cont.)

Section 3: Interface and Main Harness Connections and Preparation

Part One: RP5-GM51 Radio Interface Connections

Step 3Step 2

Step 1

Connect the four connectors from

the SR-GM14H-HAR-A Main

Harness to the indicated ports on

the RP5-GM51 module.

Remove the warning sticker on

Vehicle Connections port on the

other side of the RP5-GM51

module.

Using a small at-blade

screwdriver or similar, set the

Radio Select Dial on the side of

the RP5-GM51 to Number 4.

1 2

3

4

x

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 11

Rev: V1

Date: 030121

®

Part Two: Main Harness Connections (SR-GM14H-HAR-A)

Step 5

Step 4B

Step 4A

Plug the 6-pin lead on the Main

Harness into the RPA-VA1.

Connect the male and female ends

of the Light Green leads together.

For IOB radios, connect the white

2-pin and the black 18-pin of the

SR-GM14H-HAR-C to the Main

Harness.

For IO3, IO4, IO5 and IO6 radios,

connect the white 2-pin and the

black 18-pin of the SR-GM14H-

HAR-B to the Main Harness.

OR

Section 3: Interface and Main Harness Connections and Preparation

Step 7

Step 6

Connect the CMX Chime Module to

the 2 pin CMX Chime connector on

the Main Harness.

Connect the HEIGH10’s 24 pin AV

Harness AUX IN to AUX on the

Main Harness. Connect REVERSE

CAMERA IN to REVERSE CAM.

HEIGH10

24 Pin AV Harness

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 12

Rev: V1

Date: 030121

®

Section Four: Display Mounting Panel Preparation

Step 2Step 1 Step 3

Once all the clips are released,

remove the climate controls from

the factory bezel.

With the factory radio display /

climate control panel face down,

apply slight pressure to the front

of the controls while releasing the

locking tabs around the perimeter.

Align the controls in the HEIGH10

mounting panel and push to seat

and lock all the retaining clips.

Part One: Transferring the Climate Controls

Step 2

Step 1

Attach the display to the panel

using four M4 x 10 screws from

the HEIGH10 hardware pack.

Insert the display into the front of

the mounting panel and carefully

turn the panel over while holding

the display in place.

Part Two: Mounting the Display

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 13

Rev: V1

Date: 030121

®

Section Five: Radio Module Preparation

Part One: Radio Module Side Brackets

Step 2Step 1 Step 3

Save the cut o end pieces; they

will be used as spacers. From the

HEIGH10 hardware, four M5 x 10

screws will be used to attach the

brackets.

From the HEIGH10 hardware,

mark the two metal brackets as

shown above. Make a 90° bend

at the solid line and cut along the

dotted line.

Align one of the 90° side brackets

to the left side as shown. Bracket,

then spacer and attach with two

M5x10 screws in the locations

shown.

90° Bend Cut BracketSpacer

Step 4 Step 5

Align the other 90° bracket to

the right side as shown. Bracket,

then spacer and attach with two

M5x10 screws in the locations

shown.

From the HEIGH10 box, connect

the LVDS (Blue USB) and 10

pin display cables to the Radio

Module.

Bracket Spacer

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 14

Rev: V1

Date: 030121

®

Step 1A

Section 5: Radio Unit Installation

Step 1B Step 2

IO3, IO4, IO5, IO6: Connect

the Green and Gray vehicle

side plugs (1) on the RP5 Main

Harness to the matching plugs in

the vehicle.

IO4, IO5, IO6: If equipped,

connect the Yellow CAM-51 Input

RCA to CAMERA RCA (2) and

connect the male green/black

SWC Input to the female SWC

lead (3).

IOB: Connect the Mustard and

Gray vehicle side plugs (1) on

the RP5 Main Harness to the

matching plugs in the vehicle.

After the two vehicle side

plugs are connected, push the

connectors back into the rear

access hole as far as possible

to make room for when the radio

module is installed.

Part One: In-Vehicle Harness and Cabling Connections

1

3

2

OR

Step 4 Step 5

Temporarily place the RP5-GM51

module inside the CD/DVD

cavity while making the following

connections to the HEIGH10

Radio Module.

Plug in the two USB cables (1)

and the GPS antenna (2).

Plug in the HEIGH10’s 16 pin

Main Harness (1) and 24 pin A/V

Harness (2).

Step 3

1

2

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 15

Rev: V1

Date: 030121

®

Step 7

Connect the radio side of BAA22

Antenna Adapter (1) to the

HEIGH10’s AM/FM antenna input.

Plug in the 6 pin SWC / EXT IR

harness (2).

2018-19 IOB Only: Plug the 20

pin harness that was removed

from the factory display into the

GM5CAM-DIS-HAR.

Step 6

1

2

Section 5: Radio Unit Installation (cont.)

Part One: In-Vehicle Harness and Cabling Connections (cont.)

These are the connections for a typical installation. If adding additional cameras,

ampliers or satellite radio, those connections should be made at this point, before

mounting the radio module.

Part Two: Radio Unit Mounting

Step 2Step 1 Step 3

The plastic panel in front of the

CD/DVD cavity is narrower than

the cavity itself and will prevent

the side bracket screws from

passing. The side bracket screws

will need be angled up and over

this panel as it is put in place.

With the Chime Module and both

display cables routed over the top,

place the RP5 interface on top of

the radio module and slide it into

CD/DVD cavity as noted in Step 2.

Once in place, secure the radio

assembly with two 7mm screws.

Zip tie the Chime Module in

a suitable location. Use the

supplied two-sided tape to secure

the RP5 interface to the top of the

radio module.

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 16

Rev: V1

Date: 030121

®

Step 5Step 4

Plug the two display cables into

the back of the HEIGH10 display.

Re-connect the factory climate

control connector to the climate

controls.

Place the mounting panel in place

and temporarily secure it with two

7mm screws.

Before reassembly, it is

recommended to power up the radio

and check the chime volume* and

all other functionality...

Volume, Balance, Fade

AM/FM Reception

Bluetooth

USB

Apple Carplay

Android Auto

Camera(s)

* The Chime Module has a 4

position volume selector on the

side. Setting 1 being the loudest

and 4 being the quietest.

Section 5: Radio Unit Installation (cont.)

Part Two: Radio Unit Mounting (cont.)

Firmware Updates (RadioPRO)

The RadioPRO PC app will allow you to update the interface modules with new rmware as it becomes available. Please visit

www.PAC-audio.com/rmware to download available updates.

To update an interface module, open the RadioPRO PC app, connect the interface to your PC via a micro USB cable, and select

”Firmware” and then “Update Firmware”.

Product Updates (Firmware)

Now, select “Select File”. Finally, browse to the place where you saved the le, and select it. This will begin the updating

process. Once nished, disconnect the interface from the PC.

Firmware Updates (Stinger Radio and PAC Application APK)

To update the HEIGH10 radio rmware and PAC Application APK rmware, refer to the HEIGH10 product page:

www.stingerelectronics.com/products/heigh10

Stinger HEIGH10 Radio Replacement Kit

for select 2014-2019 Silverado/Sierra Truck

SR-GM14H

Pacific Accessory Corporation

Page 17

Rev: V1

Date: 030121

®

Reset / Restoring Interface Factory Settings

You can restore the RadioPRO interface module to factory default settings by pressing and holding the programming button

on the side of the module until the status LED starts blinking red. Once the LED starts blinking red, release the button. You

must release the button while the LED is blinking red in order to perform the reset. This reset will restore all settings to factory

defaults.

Email: support@PAC-audio.com

Phone: 866-931-8021

International: 727-592-5991

Technical Support

PN: UN1810

10-INCH MODULAR MULTIMEDIA DISPLAY SYSTEM

USER GUIDE

®

23

StingerElectronics.com StingerElectronics.com

CONTENTS

The Basics..................................4

Getting Started.........................6

AM/FM Radio............................8

Bluetooth Phone.......................9

Pairing a Device...................10

BT Device Settings.................11

Contacts/Call Log................12

Bluetooth Music......................13

SiriusXM

®

.

.................................

14

SiriusXM Replay™.................17

SiriusXM Lock Code..............18

USB Media...............................19

Apple CarPlay

®

.......................20

Android Auto™

.......................21

iPod.................................

.

........22

HDMI...................

.................

....23

AV In........................................23

Cameras.................................24

Navigation..............................25

Display Off...........

................

...25

Settings....................................26

Clock.....................................26

System Settings.....................26

Illumination............................27

Backgrounds.........................28

Display...................................28

Tabs........................................28

Camera.................................29

Audio Settings.........................30

Equalizer.................................31

Factory EQ.............................31

Crossover...............................32

Time Correction....................33

Toslink.....................................34

Gain/Volume........................34

Reset Button............................35

Trouble Shooting.....................36

Specications.

........................

38

WELCOME TO YOUR NEW

Enjoy the ride

TECHNICAL SUPPORT:

800-477-2267

[email protected]

CUSTOMER SOLUTIONS:

800-477-2267

[email protected]

Stinger is a Power Brand of AAMP Global

15500 Lightwave Drive, Suite 202

Clearwater, Florida 33760

AGREEMENT: End user agrees to use this

product in compliance with the instructions

and terms of use and with all State and

Federal laws. STINGER provides instructions

and safety warnings with respect to this

product and disclaims all liability for any

use not in conjunction with those instructions

or other misuse of its product. If you do not

agree, please discontinue use and contact

STINGER. This product is intended for off-road

use and passenger use only.

Visit StingerElectronics.com

for updates and further detailed information.

Apple CarPlay is a trademark of Apple Inc

Use of the Apple CarPlay logo means that a

vehicle user interface meets Apple performance

standards. Apple is not responsible for the

operation of this vehicle or its compliance with

safety and regulatory standards. Please note

that the use of this product with iPhone, iPod, or

iPad may affect wireless performance.

“Made for iPod,” “Made for iPhone,” and

“Made for iPad” mean that an electronic

accessory has been designed to connect

specically to iPod, iPhone, or iPad, respectively,

and has been certied by the developer to

meet Apple performance standards. Apple is

not responsible for the operation of this device

or its compliance with safety and regulatory

standards. Please note that the use of this

accessory with iPod, iPhone, or iPad may affect

wireless performance. iPad, iPhone, iPod nano,

and iPod touch are trademarks of Apple Inc.,

registered in the U.S. and other countries.

SiriusXM and all related marks and logos

are trademarks of Sirius XM Radio Inc.

Android, Android Auto, Google Play and

other marks are trademarks of Google

LLC.

The Bluetooth word mark and logos are

registered trademarks owned by

Bluetooth SIG, INC. and any use of such

marks by AAMP Global is under license.

HDMI, the HDMI Logo, and High-Denition

Multimedia Interface are trademarks

or registered trademarks of HDMI

Licensing LLC in the United States and

other countries

Stinger and the Stinger logo are

trademarks or registered trademarks of

AAMP Global in the United States and

other countries.

TM

45

StingerElectronics.com StingerElectronics.com

THE BASICS

Internal

Microphone

Reset

Button

Multifunction Knob

Press & Hold to Power On/Off

Turn to adjust Volume Up/Down

Press to Mute/Unmute

Home Button

Jump to the Home Menu Voice Button

Launches voice control

Tune/Track Up Button

Media control Next, Forward, Seek

Press & hold function in select sources

Tune/Track Down Button

Media control Previous, Back, Seek

Press & hold function in select sources

Page is loading ...

Stinger R-GM14H User manual

Related papers

Other documents