MULTISPAN LC-1046D Owner's manual

Brand: MULTISPAN

Model: LC-1046D

Type: Owner's manual

LC-1046D

AUXILIARY SUPPLY:

LENGTH COUNTER

Supply voltage

Power consumption

(VA RATING) Approx 4 VA @ 230V AC MAX

ENVIRONMENT CONDITION:

Relative Humidity

Protection Level

(AS Per Request)

Operating Temp. 0°C to 55°C

UP to 95% RH

(non-condensing)

IP-65 (Front side) As per IS/IEC

60529 : 2001

230V AC, 50Hz

Input (Start Pulse)

Display

Memory

Size

Keys

Counting Direction

Panel Cutout

Upper: 6 digit, 7 segment, 0.56” Red

Nonvolatile

Lower: 4 digit, 7 segment, 0.40” Green

96 (H) x 96 (W) x 43 (D) mm

SET/ENT, SHIFT, INC, RESET

92 (H) x 92 (W) mm

TECHNICAL SPECIFICATION

GENERAL SPECIFICATION:

DISPLAY AND KEYS:

DIMENSION:

MECHANICAL INSTALLATION

TERMINAL CONNECTION

NPN/PNP Proximity

Micro Switch

UP/ DOWN

Reset Option Front Panel Reset

Terminal Reset

Outline Dimension (mm) Panel Cutout

Dimension (mm)

INPUT SPECIFICATION:

OUTPUT SPECIFICATION:

Relay

Relay Type

Rating

1 nos.

1 C/O (NO-C-NC)

5A, 230V AC

Relay Output

PROXY COLOR CODE

+12V OUTPUT GND

Brown Black Blue

Red Green Black

LC 1046D

TOTAL

BATCH

1 2 3 4 78910

L N

www.multispanindia.com

MICRO SWITCH:- M/S Connection 7 & 9

230V AC

50Hz, 4VA

Made in India

RST

NCCNO

RELAY

+12V

I/P I/P

NPN PNP GND

LC 1046D-B1-00

MECHANICAL INSTALLATION GUIDELINES

1. Prepare the panel cutout with proper dimensions as shown

above.

2. Fit the unit into the panel with the help of clamp given.

3. The equipment in its installed state must not come in close

proximity to any heating source, caustic vapors, oils steam,

or other unwanted process byproducts.

4. Use the specified size of crimp terminal (M3.5 screws) to

wire the terminal block. Tightening the screws on the

terminal block using the tightening torque of the range of

1.2 N.m.

5. Do not connect anything to unused terminals.

INSTALLATION GUIDELINES

1. This equipment, being built-in-type, normally becomes a

part of main control panel and in such case the terminals

do not remain accessible to the end user after installation

and internal wiring.

2. Do not allow pieces of metal, wire clippings, or fine metallic

fillings from installation to enter the product or else it may

lead to a safety hazard that may in turn endanger life or

cause electrical shock to the operator.

3. Circuit breaker or mains switch must be installed between

power source and supply terminal to facilitate power ‘ON’ or

‘OFF’ function. However this mains switch or circuit breaker

must be installed at convenient place normally accessible to

the operator.

4. Use and store the instrument within the specified ambient

temperature and humidity ranges as mentioned in this

manual.

MAINTENANCE

1. The equipment should be cleaned regularly to avoid

blockage of ventilating parts.

2. Clean the equipment with a clean soft cloth. Do not use

isopropyl alcohol or any other cleaning agent.

3. Fusible resistor must not be replaced by operator.

Read complete instructions prior to installation

and operation of the unit.

WARNING : Risk of electric shock.

SAFETY PRECAUTION

All safety related codifications, symbols and instructions

that appear in this operating manual or on the equipment

must be strictly followed to ensure the safety of the operating

personnel as well as the instrument.

If all the equipment is not handled in a manner specified

by the manufacturer, it might impair the protection provided

by the equipment.

WARNING GUIDELINES

WARNING : Risk of electric shock.

1. To prevent the risk of electric shock, power supply to the

equipment must be kept OFF while doing the wiring

arrangement. Do not touch the terminals while power is

being supplied.

2. To reduce electro magnetic interference, use wire with

adequate rating and twists of the same of equal size shall

be made with shortest connection.

3. Cable used for connection to power source, must have a

cross section of 1mm or greater. These wires should have

insulations capacity made of at least 1.5kV.

4. A better anti-noise effect can be expected by using

standard power supply cable for the instrument.

1 - Total Length in meter

2 - Length Counting Speed (Meter/Min)

FRONT PANEL DESCRIPTION

To enter in parameter setting

mode

To reset total Length

To view batch count

PRESS KEYFUNCTION

OPERATOR MODE

PARAMETER SETTING MODE

Edited parameter value to be set,

And move to the next parameter

It will select the digit to modify,

When value is edited

It will change the Value of

selected digit

Press Key

RESET

01 2 3 4.5

01 2 3

To view grand total

KEY OPERATION

PARAMETER SETTING

1 2 3 4 5. 6

9 9 9 9 9. 9

9 9 9 9. 9 9

D O W N

e n a b L e

9 9 . 9

9 9 9 9 9 9

m e d I u m

9 9 9 9

S E C O N D

1 2 3. 4

s e t

d I a

C O N T

p a s s

t I m e

D P

p u L S

P P R

P A S S

Change by

& Key

Change by

& Key

Change by

& Key

Change by

Key

Press key

SET

ENT

SET

ENT

SET

ENT

SET

ENT

SET

ENT

SET

ENT

SET

ENT

SET

ENT

Total Length in Mtr.

Speed in Mtr/Min

Set Length Value

Set Diameter Value

Set Count Direction

Enable Mode : Password

will show on display

Disable Mode : Password

will not show on display

direct show set point

(UP & Down)

Set Time Value

Set Decimal Point

Set Speed Selection

Set PPR Selection

First : First it will show

password then it will

show the set point

Second : First it will show

set point it will show the

password

Press key for save & exit

SET

ENT

NOTE

1). The proximity switch give pulse to counter everytime the

metal on the roller is sensed.

2). Length of Material ( in meter ) for one revolution

= 3.14 X Diameter (mm)

3). Total length

= { 3.14 X Diameter (mm) X Number of Revolutions } / 1000

4). Total Meters/Minute

= { 3.14 X Diameter (mm) X RPM } / 1000 X PPR

WORKING

1). When proxy pulse comes, upper display indicates increment

in ‘Total Length’ in Meter, Lower Display indicates‘Speed’

in Meter/Min according to Diameter and PPR set.

2). For Manual Reset Mode, Set time = 00.0 sec &

For Auto Reset Mode, Set time = 00.1 to 99.9 sec.

3). When Total Length = Set Length, Then Relay will energies ,

and remains ON till Set Auto Reset Time. Relay will turn off

after completion of time.

If time is set = 00.0 sec. then relay remains ON until key

is pressed.

4). If there is a power failure, the last reading is stored in the

memory and Counter starts resume counting from the last

stored value, when power ON.

5). No. of bolts inserted in a roller should be the same as that

of PPR.

Dia mm

20mm Minimum

4mm Distance

Proximity

Note:

PROXY ALIGEMENT

1). Please consult support engineers for sensing area size for

proxy to sense.

2). Please ensure proper sensing area size before installing

proxy sensor in your equipment.

3). Sensing area must be equal or more than the proxy

head size.

NOTE

Slow ( Max. RPM 500)

Medium ( Max. RPM 5000)

Fast ( Max. RPM 15000)

Change by

Key

Change by

Key

Change by

Key

Change by

Key

Change by

Key

Range :- 000.001

to 99999 mtr

Range :- 00.0

to 99.9 sec

Range :- 0000.01

to 9999.99 mm

Range :-

999.999,

9999.99, 99999.9

& 999999

Pulse per revolution

2 5

p a s s

Change by

& Key

Press key

SET

ENT

Password 25 Fix

MULTISPAN LC-1046D Owner's manual

MULTISPAN LC-1046D Owner's manual

MULTISPAN LC-1046D Owner's manual

Related papers

Other documents