Parkside PAHS 12 A1 Operation and Safety Notes

Brand: Parkside

Model: PAHS 12 A1

Category: Power sanders

Type: Operation and Safety Notes

This manual is also suitable for

88933

IAN 88933

BATTERY POWERED PALM SANDER PAHS 12 A1

AKKU-HANDSCHLEIFER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

BATTERY POWERED PALM SANDER

Operation and Safety Notes

Translation of original operation manual

AKUMULATORSKI ROČNI BRUSILNIK

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

AKU RUČNÍ BRUSKA

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

GB Operation and Safety Notes Page 5

SI Navodila za upravljanje in varnostna opozorila Stran 15

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 25

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 35

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

4 4 a

5 GB

Table of contents

Introduction

Proper use ............................................................................................................................................Page 6

Features ...............................................................................................................................................Page 6

Scope of delivery ................................................................................................................................Page 6

Technical Data ....................................................................................................................................Page 6

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 8

5. Use and handling of the cordless electrical power tool ..............................................................Page 9

6. Service .............................................................................................................................................Page 9

Safety notices specifically pertaining to hand grinders ....................................................................Page 9

Safety notices specifically pertaining to chargers .............................................................................Page 9

Before Initial Use

Removing / charging / inserting the battery pack .............................................................................Page 10

Checking the battery charge .............................................................................................................. Page 10

Start-up

Vacuum dust extraction ......................................................................................................................Page 10

Dust box for internal vacuum extraction ............................................................................................ Page 10

Adapter for external vacuum extraction (with reducer piece) .........................................................Page 11

Rotating the backing plate .................................................................................................................Page 11

Advice on use ......................................................................................................................................Page 11

Maintenance and cleaning ............................................................................................... Page 11

Service centre ..............................................................................................................................Page 11

Warranty .........................................................................................................................................Page 12

Disposal ............................................................................................................................................Page 12

Declaration of Conformity / Manufacturer..........................................................Page 13

6 GB

Introduction / General safety advice for electrical power tools

Introduction

Battery powered palm sander

PAHS 12 A1

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product.

The instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as descri-

bed and for the speciﬁed applications. If you pass

the product on to anyone else, please ensure that

you also pass on all the documentation with it.

Proper use

This device – when combined with the appropriate

sandpaper – is suitable for dry-sanding wood, plas-

tic, metal, ﬁller and painted surfaces. The device is

particularly suitable for corners, proﬁles or diﬃcult to

access places. Any other use or modiﬁcation to the

device shall be considered as improper use and

could give rise to considerable dangers. We will

not accept liability for loss or damage arising from

improper use. Not suitable for commercial use.

Features

Rechargeable battery pack

Battery pack release button

Adapter connection

Adapter for external dust extractionr

Reducer

Tab (dust box)

Dust box for self-generated dust extraction

Dust box release button

Vents

Patented grinding plate (360° pivot)

ON / OFF switch

Rechargeable battery LED signals

Charge indicator red

Charge indicator green

Charger

Scope of delivery

1 Battery powered palm sander

3 Sanding sheets (60 / 80 / 120 grit)

1 Rechargeable battery pack

1 Charger

1 Adapter for external dust extraction with reducer

1 Dust box

1 Carrying case

1 Instructions for use

Technical Data

Battery powered palm sander PAHS 12 A1:

Rated speed: n

10000 rpm

Rated frequency: n

20000 rpm

Grinding plate: 360° pivot

Rechargeable Battery Pack PAHS 12 A1-1:

Type: LITHIUM-ION

Rated voltage: 12 V

Capacity: 1300mAh

Charger PAHS 12 A1-2:

Input:

Rated voltage: 230 V∼, 50 Hz

Rated power: 16 W

Output:

Rated voltage: 11.5 V

Rated current: 600 mA

Charging time: approx. 180 min

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accord-

ance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 79.2 dB(A)

Sound power level: 90.2 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration a

= 6.188 m / s

Uncertainty K = 1.5 m / s

7 GB

Introduction / General safety advice for electrical power tools

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Try to keep the vibration loads as low as possible.

Measures for the reduction of the vibration load are,

for example, wearing gloves and reduction of the

working time. Here, all parts of the operating cycle

have to be calculated in (i.e. times where the elec-

trical tool is switched oﬀ and the times where the

electrical tool is switched on but is running without

load).

General safety advice

for electrical power tools

Read all the

safety advice and instructions!

Failure to observe the safety advice and

instructions may result in electric shock, ﬁre and /

or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electric-

ity (by means of a mains lead) and electrical tools

mains lead).

Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas

can lead to accidents.

b) Do not work with the device in poten-

tially explosive environments in which

there are inflammable liquids, gases

or dusts. Electrical power tools create

sparks, which can ignite dusts or fumes.

Keep children and other people away

while you are operating the electrical

tool. Distractions can cause you to lose con-

trol of the device.

Electrical safety

The mains plug on the device must match

the mains socket. The plug must not

be modified in any way. Do not use

an adapter plug with devices fitted

with a protective earth. Unmodiﬁed

plugs and matching sockets reduce the risk of

electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended, e.g.

to carry the device, to hang up the de-

vice or to pull the mains plug out of the

mains socket. Keep the mains lead

away from heat, oil, sharp edges or

moving parts of the device. Damaged or

tangled mains leads increase the risk of elec-

tric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also approved

for use outdoors. The use of an extension

cable suitable for outdoor use reduces the risk

of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electri-

cal power tool in a moist environment

is unavoidable. The use of an RCD reduces

the risk of electric shock.

Introduction

8 GB

General safety advice for electrical power tools

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b) Wear personal protective equipment

and always wear safety glasses. The

wearing of personal protective equipment such

as dust masks, non-slip safety shoes, safety hel-

mets or ear protectors, appropriate to the type

of electrical power tool used and work under-

taken, reduces the risk of injury.

c) Avoid accidental starting. Ensure the

power tool is switched oﬀ before con-

necting it to the mains and or connec-

ting the battery, before picking it up

or carrying it. Accidents can happen if you

carry the device with your ﬁnger on the ON /

OFF switch or with the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing

and balance at all times. By doing this

you will be in a better position to control the

device in unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

9 GB

General safety advice for electrical power tools

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Use and handling of the

cordless electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

b) Only the rechargeable battery units

supplied are to be used with an elec-

trical power tool. The use of other recharge-

able battery units may lead to the danger of

injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

d) Fluids may leak out of rechargeable

battery units if they are misused. If

this happens, avoid contact with the

ﬂuid. If contact occurs, ﬂush the af-

fected area with water. Seek addi-

tional medical help if any of the ﬂuid

gets into your eyes. Escaping battery ﬂuid

may cause skin irritation or burns.

6. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Safety notices speciﬁcally

pertaining to hand grinders

DANGER DUE TO DUST!

When working on wood for extended periods

and particularly when working on materials

which generate dust which is dangerous to the

health, be sure to connect it to a suitable dust

extractor. Wear safety glasses and a dust mask.

Avoid sanding paint containing lead or other

materials harmful to your health.

TOXIC FUMES! Working

with harmful / toxic dust poses a risk to the

health of the person operating the unit and to

anyone nearby.

RISK OF FIRE FROM FLYING SPARKS!

Grinding metals produces flying sparks. Thus

be very careful not to endanger persons, and

that no flammables are near the work area.

Ensure proper ventilation when working on pla-

stics, paint, lacquer, etc.

Do not work on damp materials or moist surfaces.

Do not work on materials containing asbestos.

Asbestos is considered carcinogenic.

Never use the device for any purpose other

than the intended purpose and only use it with

the original parts and accessories. Using parts

or accessories not speciﬁed in the instructions

may result in injuries.

Secure the work-piece. Use clamps or a

vice to secure the work piece. This will secure it

more safely than your hand.

Safety notices speciﬁcally

pertaining to chargers

(EN60335-1 / EN60335-2-29)

If the mains cable for this unit becomes dama-

ged it must be replaced by customer service or

similarly qualiﬁed professionals to avoid hazards.

Children or persons (including children) who

lack the knowledge or experience to use the

device or whose physical, sensory or intellectual

capacities are limited must never be allowed to

use the device without supervision or instruction

by a person responsible for their safety.

General safety advice for electrical power tools

10 GB

Start-up / Maintenance and cleaning / Service centre

General safety advice for electrical power tools / Before Initial Use / Start-up

Children should be supervised to ensure that

they do not play with the device.

Single use, non-rechargeable batteries must

never be recharged.

Before Initial Use

Removing / charging /

inserting the battery pack

Note: The battery packed is delivered partly

charged.

Charge the battery pack with the included charger,

ideally for a minimum of 3 hours. This will ensure

the battery delivers full power. Li-Ion batteries can

be charged at any time without reducing the life. In-

terrupting the charging process does not damage

the rechargeable battery.

1. To remove the rechargeable battery pack

press the release buttons

and slide the bat-

tery pack

out of the unit.

2. Insert the battery pack

into the charger

3. Insert the mains plug into the mains socket. The

charge indicator

will light up red.

4. The green charge indicator

shows charging

is complete and the battery pack

is ready

for use.

5. Slide the battery pack

into the unit.

Checking the battery charge

The battery LED

indicates the status or remain-

ing charge as:

RED/ YELLOW/ GREEN = maximum charge/ power

RED/ YELLOW = medium charge/ power

RED = low charge – recharge battery

Start-up

Note! Always switch the hand grinder on before

applying it to the material, then apply.

Switching the unit on:

Press the ON / OFF switch

Switching the unit off:

Press the ON / OFF switch

Vacuum dust extraction

DANGER OF FIRE! There is

the danger of ﬁre when working with electrical

devices that have a dust box or can be connected

to a vacuum cleaner. Under certain conditions the

wood dust in the dust extraction bag (or in the

vacuum‘s dust bag) may ignite, e.g. as a result of

ﬂying sparks generated when abrading metals or

metal objects left in wood. This can happen par-

ticularly if the wood dust is mixed with paint resi-

due or other chemicals and the abraded particles

are hot from prolonged abrasion. Therefore you

must empty the device’s dust collection box and the

vacuum cleaner’s dust bag before taking a break

or stopping work and always avoid overheating of

the abraded particles and the device.

Wear a dust mask!

Dust box for internal

vacuum extraction

Mounting:

Slide the dust box for self-generated dust ext-

raction

up to the stop on the hand sander.

Removal:

Press the release button

of the dust extraction

box for internal vacuum extraction

and

withdraw it towards the rear of the device.

Note: Empty the dust collector in good time in or-

der to ensure the optimum removal of

dust by

suction.

To do so, remove the dust box

from the de-

vice as described above. Open the dust box

by pulling on the tab

and remove the cover.

Now tap both parts to thoroughly clean them.

11 GB

Start-up / Maintenance and cleaning / Service centre

Adapter for external vacuum

extraction (with reducer piece)

Connection:

Push the adapter for external vacuum extraction

into the adapter connection

If it is necessary to use the reducer piece

push the reducer piece into the adapter for

external vacuum extraction

Push the hose of a suitable dust extraction de

vice approved for that purpose (e.g. a work-

shop vacuum cleaner) on to the adapter for

external vacuum extraction

or the reducer

piece

Removal:

Pull the hose of the dust extraction device oﬀ

the adapter for external vacuum extraction

Pull oﬀ the adapter for external vacuum extrac-

tion

(with the reducer piece

if used).

Attaching / detaching

sanding sheets

Attaching:

Sanding sheets are attached to the backing plate

by means of the hook and pile fastening.

Detaching:

Simply pull the sanding sheet oﬀ the backing

plate

(see Fig. C).

Rotating the backing plate

Rotate the backing plate

into the desired

position (see Fig. D).

Sanding and surfaces:

The sanding output and the quality of the surface

ﬁnish are determined by the grade of grit on the

sanding sheet.

Always use sanding sheets with grades that

are suitable for the particular surface you are

sanding.

Advice on use

Switch the device on before placing it against

the workpiece.

Apply light sanding pressure only.

Advance the device at an even rate.

Change sanding sheets at the appropriate time.

Do not work on diﬀerent types of material using

the same sanding sheet (e.g. wood and then

metal).

Clean the sanding sheet from time to time with

a vacuum cleaner.

Sand diﬃcult to reach places with the front or

side corners of the backing plate

Maintenance and cleaning

Always pull the mains plug is out

of the socket before doing any work on the device.

The battery powered palm sander is maintenance-free.

For cleaning the housing use a dry cloth only.

Remove any adhering sanding dust with a

narrow paint brush.

Never any kind of sharp object or petrol,

solvents or cleaning agents that might attack

plastic. Do not allow any liquids to enter the

inside of the device.

Always keep the ventilation slots

clear.

Service centre

Have your device

repaired only by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

If the plug or mains

lead needs to be replaced, always

have the replacement carried out by

the manufacturer or its service centre.

This will ensure that your device remains safe

to use.

General safety advice for electrical power tools / Before Initial Use / Start-up

12 GB

Declaration of Conformity / Manufacturer

Warranty / Disposal

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tamper-

ing not carried out by our authorized service branch.

Your statutory rights are not restricted in any way

by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: k[email protected]

IAN 88933

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electrical

power tools with the household

rubbish!

In accordance with European Directive 2002 / 96 / EC

(covering waste electrical and electronic equipment)

and its transposition into national legislation, worn

out electrical power tools must be collected separately

and taken for environmentally compatible recycling.

Do not dispose of rechargeable

batteries with your household

refuse!

Defective or worn out rechargeable batteries must

be recycled according to Directive 2006 / 66 / EC.

Dispose of batteries and appliances over the existing

collection facilities.

Contact your local refuse disposal authority for

more details of how to dispose of your worn out

electrical devices.

13 GB

Declaration of Conformity /

Manufacturer

We, KOMPERNASS GMBH, the person responsible

for documents: Mr Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that

this product complies with the following standards,

normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EC Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-1/A11:2010

EN 60745-2-4/A11:2011

EN 55014-1/A2:2011

EN 55014-2/A2:2008

EN 60335-2-29:2004+A2:10

EN 60335-1:2002+A11,A1:04+A12,

A2:06+A13:08+A14:10+A15:11

EN 62233:2008

EN 55014-1:2006+A1:2009+A2:2011

EN 55014-2:1997+A1:2001+A2:2008

EN 61000-3-2:2006+A1:2009+A2:2009

EN 61000-3-3:2008

and conﬁrm this with the CE symbol.

Type / Machine designation:

Battery powered palm sander PAHS 12 A1

Date of manufacture (DOM): 03–2013

Serial number: IAN 88933

Bochum, 31.03.2013

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations

in the course of product development.

Declaration of Conformity / Manufacturer

Warranty / Disposal

Kazalo

15 SI

Kazalo

Uvod

Uporaba v skladu z določili .............................................................................................................. Stran 16

Oprema .............................................................................................................................................. Stran 16

Obseg dobave ................................................................................................................................... Stran 16

Tehnični podatki ................................................................................................................................. Stran 16

Splošna varnostna navodila za električno orodje

1. Varnost na delovnem mestu .......................................................................................................... Stran 17

2. Električna varnost ........................................................................................................................... Stran 17

3. Varnost oseb .................................................................................................................................. Stran 18

4. Skrbno ravnanje in uporaba električnega orodja ....................................................................... Stran 18

5. Uporaba akumulatorskega orodja in ravnanje z njim ................................................................ Stran 19

6. Servis .............................................................................................................................................. Stran 19

Posebna varnostna opozorila za ročni brusilnik .............................................................................. Stran 19

Posebna varnostna opozorila za polnilnike ..................................................................................... Stran 19

Pred začetkom obratovanja

Odstranitev akumulatorja / polnjenje / vstavljanje ........................................................................... Stran 20

Preverjanje stanja akumulatorja ........................................................................................................ Stran 20

Začetek uporabe

Odsesavanje prahu ........................................................................................................................... Stran 20

Škatla za prah za lastno odsesavanje ............................................................................................. Stran 20

Adapter za dodatno odsesavanje (z reducirnim kosom) ................................................................ Stran 21

Pritrjevanje / odstranjevanje brusilnega lista .................................................................................... Stran 21

Vrtenje brusilne plošče ....................................................................................................................... Stran 21

Navodila za delo ............................................................................................................................... Stran 21

Vzdrževanje in čiščenje ...................................................................................................... Stran 21

Servis ................................................................................................................................................. Stran 21

Garancija ........................................................................................................................................ Stran 22

Odstranjevanje ......................................................................................................................... Stran 22

Izjava o skladnosti / Izdelovalec ................................................................................ Stran 23

Garancijski list ........................................................................................................................... Stran 24

16 SI

Akumulatorski ročni brusilnik

PAHS 12 A1

Uvod

Iskrene čestitke ob nakupu vaše nove naprave. Od-

ločili ste se za zelo kakovosten izdelek. To navodilo

za uporabo je sestavni del tega izdelka. Vsebuje

pomembna navodila za varnost, uporabo in odstrani-

tev. Preden začnete izdelek uporabljati, se seznanite

z vsemi navodili za uporabo in varnostnimi napotki.

Izdelek uporabljajte samo tako, kot je opisano, in

samo za navedena področja uporabe. Če izdelek

odstopite novemu lastniku, mu zraven izročite tudi

vse dokumente.

Uporaba v skladu z določili

Naprava je – odvisno od brusilnega papirja –

predvidena za suho brušenje lesa, umetnih snovi,

kovin, kita in lakiranih površin. Naprava je posebno

primerna za kote, proﬁle in težko dostopna mesta.

Kakršnakoli drugačna uporaba ali sprememba na-

prave ni v skladu z določili in predstavlja znatno ne-

varnost nesreč. Za škodo, nastalo pri uporabi, ki ni v

skladu z določili, ne prevzamemo jamstva. Naprava

ni namenjena za profesionalno uporabo.

Oprema

Akumulator

Gumb za sprostitev akumulatorja

Adapterski priključek

Adapter za dodatno izsesavanje

Reducirni kos

Spona (posoda za prah)

Posoda za prah za lastno izsesavanje

Gumb za sprostitev posode za prah

Prezračevalne odprtine

Patentirana brusna plošča (vrtljiva za 360°)

Tipka za VKLOP / IZKLOP

LED lučke akumulatorja

Prikaz stanja napolnjenosti, rdeči

Prikaz stanja napolnjenosti, zeleni

Polnilnik

Obseg dobave

1 akumulatorski ročni brusilnik

3 brusne plošče (zrnavost 60 / 80 / 120)

1 akumulator

1 polnilnik

1 adapter za dodatno odsesavanje prahu z redu-

cirnim kosom

1 posoda za prah

1 nosilni kovček

1 navodila za uporabo

Tehnični podatki

Akumulatorski ročni brusilnik PAHS 12 A1:

Nazivno število vrtljajev: n

10000 min

-1

Nazivno število nihajev: n

20000 min

-1

Brusna plošča: vrtljiva za 360°

Akumulator PAHS 12 A1-1:

Tip: LITIJ-ION

Nazivna napetost: 12 V

Kapaciteta: 1300 mAh

Polnilnik PAHS 12 A1-2:

VHOD:

Nazivna napetost: 230 V∼, 50 Hz

Nazivna moč: 16 W

IZHOD:

Nazivna napetost: 11,5 V

Nazivni tok: 600 mA

Trajanje polnjenja: pribl. 180 min

Zaščitni razred: II /

Podatki o hrupu in vibracijah:

Izmerjena vrednost za hrup določena v skladu z

EN 60745. Raven hrupa električnega orodja po

A-vrednotenju tipično znaša:

Nivo zvočnega tlaka: 79,2 dB(A)

Nivo hrupa: 90,2 dB(A)

Negotovost K: 3 dB

Uporabljajte zaščitne glušnike!

Uvod

Uvod / Splošna varnostna navodila za električno orodje

17 SI

Uvod

Ocenjeni pospešek, tipično:

Vibracije na dlani in roki a

= 6,188 m / s

Negotovost K = 1,5 m / s

Nivo nihanja, ki je naveden v

teh navodilih, je bil merjen skladno z merilnim po-

stopkom, normiranim po standardu EN 60745, in se

ga lahko uporablja za primerjavo naprav. Nave-

deno vrednost emisije nihanja lahko uporabite tudi

za uvodno ocene izpostavitve.

Nivo nihanja se bo spreminjal skladno z uporabo

električnega orodja in lahko v nekaterih primerih

leži nad vrednostjo, navedeno v teh navodilih. Ka

dar

se električno orodje redno uporablja na tak način,

bi nihajno obremenitev lahko podcenili.

Poskusite ohraniti obremenitev zaradi vibracij čim

nižjo. Najboljši ukrep za zmanjšanje obremenitve

zaradi vibracij je nošnja rokavic med uporabo orodja

in omejitev delovnega časa. Pri tem je treba upošte-

vati vse dele obratovalnega cikla (npr. čase, med

katerimi je električno orodje izklopljeno, in čase, ko

je sicer orodje vklopljeno, vendar deluje brez obre-

menitve).

Splošna varnostna navodila

za električno orodje

Preberite var-

nostna opozorila in navodila!

Neupoštevanje varnostnih opozoril in

navodil lahko vodi do povzročitve električnega

udara, požara in / ali hudih poškodb.

Vsa varnostna opozorila in navodila shra-

nite za uporabo v prihodnje!

V varnostnih navodilih uporabljeni pojem “električno

orodje“ se nanaša na električno orodje na omrežni

pogon (s kablom za priključitev na omrežje) in na

električno orodje na akumulatorski pogon (brez

kabla za priključitev na omrežje).

Varnost na delovnem mestu

a) Delovno območje naj bo vedno čisto

in dobro osvetljeno. Nered in neosvetljena

delovna področja so lahko vzrok za nezgode.

b) Z orodjem ne delajte v okolici, kjer ob-

staja nevarnost eksplozije in v kateri

se nahajajo vnetljive tekočine, plini ali

prah. Električna orodja proizvajajo iskrice, ki

bi lahko povzročile vžig prahu ali pare.

c) Poskrbite, da bodo otroci in druge

osebe med uporabo električnega orod

dovolj oddaljene od mesta uporabe.

Če vaša pozornost ni v celoti usmerjena na

delo, lahko izgubite nadzor nad orodjem.

Električna varnost

Priključni vtič mora ustrezati električni

vtičnici. Vtiča v nobenem primeru ne

smete spreminjati. Skupaj z ozemljenimi

stroji ne uporabljajte dodatnih nastav

kov vtiča. Originalen nespremenjen vtič in

ustrezna vtičnica zmanjšata tveganje električ-

nega udara.

b) Preprečite telesni stik z ozemljenimi

površinami, kot so cevi, grelci, štedilniki

in hladilniki. Obstaja povečano tveganje

električnega udara, če je vaše telo ozemljeno.

c) Preprečite stik orodja z vodo ali vlago.

Vdor vode v električno orodje poveča tveganje

električnega udara.

d) Kabla ne uporabljajte za nošenje

orodja, za obešanje orodja ali za vle-

čenje vtiča iz vtičnice. Kabel zavarujte

pred vročino, olji, ostrimi robovi ali

gibljivim delom orodja. Poškodovani ali

zavozlani kabli povečajo tveganje električ-

nega udara.

e) Kadar z električnim orodjem delate na

prostem, uporabljajte samo električne

podaljške, ki so primerni in namenjeni

uporabi na prostem. Uporaba električnega

podaljška, ki je izdelan za uporabo na prostem,

zmanjša tveganje električnega udara.

f) Če se uporabi električnega orodja

v vlažnem okolju ne da izogniti,

Uvod / Splošna varnostna navodila za električno orodje

18 SI

upora bljajte zaščitno stikalo za ok-

varni tok. Uporaba zaščitnega stikala za

okvarni tok zmanjša tveganje električnega

udara.

3. Varnost oseb

a) Ves čas bodite pozorni, pazite, kaj de-

late in pri delu z električnim orodjem

ravnajte razumno. Orodja ne upora-

bljajte, če ste utrujeni ali če ste

pod

vplivom droge, alkohola ali zdravil

Trenutek nepozornosti med uporabo orodja

lahko povzroči resne poškodbe.

b) Vedno uporabljajte osebno zaščitno

opremo in vedno zaščitna očala. Upo-

raba osebne zaščitne opreme kot so maska za

prah, delovni čevlji z zaščito proti drsenju, za-

ščitna čelada ali zaščita sluha, odvisno od na-

čina uporabe električnega orodja, zmanjšuje

tveganje nastanka poškodb.

c) Preprečite nenameren vklop naprave.

Prepričajte se, ali je električno orodje

izklopljeno, preden ga priključite na

napajanje in / ali akumulator, ga dvi-

gnete ali nosite. Če imate pri nošenju na-

prave prst na stikalu za VKLOP / IZKLOP ali je

naprava vklopljena, to lahko vodi do povzro-

čitve nesreč.

d) Pred vklopom orodja odstranite vsa

orodja, ki jih potrebujete za nastavi-

tve in vse vijačne ključe. Orodje ali ključ

v vrtečem se delu orodja bi lahko povzročil

poškodbe.

e) Izogibajte se abnormalni telesni drži.

Skrbite za varno stojišče in pazite na

ravnotežje. Na ta način lahko napravo, še

posebno v nepričakovanih situacijah, bolje

kontrolirate.

f) Oblečeni bodite v primerna oblačila.

Ne nosite širokih oblačil ali nakita.

Poskrbite, da v bližino vrtečih se de-

lov stroja ne pridejo lasje, oblačila in

rokavice. Ohlapna oblačila, nakit ali dolgi

lasje bi se lahko ujeli v premikajoče se dele.

g) Kadar je vgrajena oprema za odsesa-

vanje ali prestrezanje prahu, se

prepričajte, da je oprema priključena

in pravilno uporabljena. Uporaba

opreme zmanjša ogrožanje zaradi prahu.

Skrbno ravnanje in uporaba

električnega orodja

a) Naprave ne preobremenjujte. Za vaše

delo uporabljajte za to namenjeno

električno orodje. Z ustreznim električnim

orodjem boste v določenem območju zmoglji-

vosti delali bolje in bolj varno.

b) Ne uporabljajte električnega orodja,

čigar stikalo je defektno. Električno orod

je,

ki se ne da več vklopiti ali izklopiti, je nevarno

in ga je treba dati v popravilo.

c) Preden izvajate nastavitve na napravi,

zamenjujete dele opreme ali napravo

daste iz rok, izvlecite električni vtič iz

vtičnice in / ali odstranite akumulator.

Ti previdnosti ukrepi preprečujejo nenameren

zagon električnega orodja.

d) Neuporabljano električno orodje hra-

nite zunaj dosega otrok. Osebam, ki z

napravo niso seznanjene ali niso pre-

brale teh navodil, uporabe naprave

ne dovolite. Električno orodje je nevarno, če

ga uporabljajo neizkušene osebe.

e) Napravo skrbno negujte. Kontroli-

rajte, če premikajoči se deli naprave

brezhibno delujejo in se ne zatikajo,

če so deli naprave odlomljeni ali

poškodovani, ter da delovanje na-

prave ni ovirano. Poškodovane dele

dajte pred ponovno uporabo naprave

v popravilo. Vzrok za mnoge nesreče je

slabo vzdrževano električno orodje.

f) Poskrbite, da bodo rezalna orodja

vedno ostra in čista. Skrbno vzdrževana

rezalna orodja z ostrimi rezili se ne zatikajo in

so lažje vodljiva.

g) Električna orodja, dodatno opremo,

nastavke itd. uporabljajte v skladu z

navodili za uporabo in na način, ki je

predpisan posebej za ta specialni tip

stroja. Vedno upoštevajte delovne po-

goje in vrsto dela, ki ga želite opraviti.

Splošna varnostna navodila za električno orodje

19 SI

Splošna varnostna navodila za električno orodje

Uporaba električnih orodij v namene, ki se raz-

likujejo od namenov, ki jih je predvidel proizva-

jalec, lahko povzroči nastanek nevarnih situacij.

5. Uporaba akumulatorskega

orodja in ravnanje z njim

a) Akumulatorje polnite samo v polnilnih

napravah, ki jih je priporočil izdelova-

lec. Za polnilno napravo, ki je namenjena za

določeno vrsto akumulatorjev, obstaja nevarnost

požara, če se jo uporablja z drugimi akumulatorji.

b) V električnem orodju uporabljajte samo

akumulatorje, ki so za to namenjeni.

Uporaba drugih akumulatorjev lahko vodi do

povzročitve poškodb in nevarnosti požara.

c) Akumulatorje, katerih ne uporabljate,

hranite stran od pisarniških sponk,

kovancev, ključev, žebljev, vijakov ali

drugih majhnih kovinskih predmetov,

ki bi lahko povzročili premostitev kon-

taktov. Kratki stik med kontakti akumulatorja

ima lahko za posledico povzročitev opeklin ali

požara.

V primeru napačne uporabe lahko iz

akumulatorja izteče tekočina. Izogi

bajte

se kontaktu s to tekočino. V primeru

naključnega kontakta prizadeto mesto

sperite z vodo. Če tekočine pride v oči,

dodatno poiščite tudi zdravniško po

moč.

Tekočina, ki izteka iz akumulatorja, lahko pov-

zroči draženje kože ali opekline.

6. Servis

a) Vaše naprave dajte vpopravilo servi-

sni službi ali strokovnjaku za električne

naprave, popravilo pa naj poteka

samo z originalnimi nadomestnimi

deli.

Na ta način se zagotovi, da varnost naprave

ostane ohranjena.

Posebna varnostna opozorila

za ročni brusilnik

NEVARNOST ZARADI

PRAHU! Pri dlje časa trajajoči obdelavi lesa

in še posebej, če obdelujete material, pri ka

terem

nastaja zdravju škodljivi prah, priključite napravo

na ustrezno zunanjo napravo za odsesavanje

prahu. Nosite zaščitna očala in protiprašno

masko!

Izogibajte se brušenju barv z vsebnostjo svinca

ali drugih materialov, ki vsebujejo zdravju

škodljive snovi.

STRUPENI HLAPI!

Obdelava škodljivega / strupenega prahu

predstavlja ogrožanje zdravja za upravljavca

ali osebe, ki se nahajajo v bližini.

NEVARNOST POŽARA ZARADI IS-

KRENJA! Kadar brusite kovine, pride do is-

krenja. Zato nujno pazite, da ne ogrožate oseb

in da se v bližini delovnega območja ne naha-

jajo vnetljivi materiali.

Pri obdelavi umetnih mas, barv, lakov ipd. po-

skrbite za zadostno prezračevanje.

Ne obdelujte vlažnih materialov ali površin.

Materiala, ki vsebuje azbest, ne smete obdelo-

vati. Azbest velja za kancerogeno snov.

Napravo uporabljajte samo v namene, za

katere je primerna, in samo z originalnimi

deli / priborom. Uporaba drugih delov, ki niso

priporočeni v navodilu za uporabo, ali drug-

ega pribora lahko pomeni za vas nevarnost

poškodbe.

Zavarujte obdelovanca. Uporabljajte

vpenjalno pripravo / primež, v katerem bo ob-

delovanec varno nameščen. Tako ga boste

varneje držali kot z roko.

Posebna varnostna opozorila

za polnilnike (EN60335-1 /

EN60335-2-29)

Če je napeljava za priključitev naprave na

omrežje poškodovana, jo mora zamenjati

proizvajalec ali njegova servisna služba ali

podobno usposobljena oseba, da se prepreči

nevarnosti.

Splošna varnostna navodila za električno orodje

20 SI

Ta naprava ni namenjena za to, da jo uporabl-

jajo osebe (vključno z otroci), ki so omejene v

telesnih, zaznavnih ali duševnih zmogljivostih

ali jim primanjkuje izkušenj in / ali znanja, razen

v primeru, če jih nadzira oseba, odgovorna za

njihovo varnost, ali pa so od te osebe dobili

navodila o tem, kako se napravo uporablja.

Otroke je treba nadzorovati, da se prepričate,

da se ne igrajo z napravo.

Ne polnite baterij, ki se ne smejo ponovno

polniti.

Pred začetkom obratovanja

Odstranitev akumulatorja /

polnjenje / vstavljanje

Napotek: Akumulator je ob dobavi delno napol-

njen. Če je mogoče, pred zagonom obratovanja

polnite akumulator najmanj 3 ure v polnilniku. Tako

boste zagotovili polno moč akumulatorja. Li-ionski

akumulator lahko kadar koli polnite, ne da bi s tem

skrajšali uporabno dobo. Prekinitev postopka pol-

njenja akumulatorju ne škoduje.

1. Za odstranitev akumulatorja

pritisnite gumba

za sprostitev

in povlecite akumulator

naprave.

2. Vtaknite akumulator

v polnilnik

3. Električni vtič vtaknite v vtičnico. Prikaz stanja

napolnjenosti

sveti rdeče.

4. Zeleni prikaz stanja napolnjenosti

pomeni,

je polnjenje zaključeno in da je akumulator

pripravljen za uporabo.

5. Potisnite akumulator

v napravo.

Preverjanje stanja akumulatorja

Stanje oz. preostala moč je v LED lučki akumulatorja

prikazana kot sledi:

RDEČA / RUMENA / ZELENA = maksimalna napol-

njenost / moč

RDEČA / RUMENA = srednja napolnjenost / moč

RDEČA = skoraj prazen – napolnite akumulator

Začetek uporabe

Napotek! Ročni brusilnik vedno najprej vključite

in ga šele nato približajte obdelovancu.

Vklop naprave:

Pritisnite tipko za VKLOP / IZKLOP

Izklop naprave:

Pritisnite tipko za VKLOP / IZKLOP

Odsesavanje prahu

NEVARNOST POŽARA!

Pri delu z električnimi napravami, ki razpolagajo s

škatlo za prah ali se jih s pomočjo neke priprave

za odsesavanje prahu lahko priključi na sesalnik

za prah, obstaja nevarnost požara! Pod neugodnimi

pogoji, kot npr. pri letenju isker, pri brušenju kovin

ali ostankov kovin v lesu, se lahko lesni prah v škatli

za prah (ali v vrečki za prah sesalnika za prah) sam

vname. To se še posebno lahko zgodi takrat, kadar

je lesni prah pomešan z ostanki laka ali drugih

kemičnih snovi in je po dolgotrajnem delu vroč.

Zaradi tega se obvezno izogibajte pregrevanju

brušenega materiala in naprave in pred odmori

med delom prestrezno škatlo za prah oz. vrečko

za prah v sesalniku za prah vedno izpraznite.

Nosite protiprašno zaščitno masko!

Škatla za prah za

lastno odsesavanje

Priključitev:

Potisnite zaboj za prah za lastno sesanje

ročni brusilnik vse do konca.

Snemanje:

Pritisnite tipki za sprostitev

škatle za prah

za lastno odsesavanje

in s potegom nav-

zdol škatlo snemite.

Napotek: Za zagotavljanje optimalne sposob-

nosti sesanja, zaboj za prah za lastno sesanje

pravočasno izpraznite.

Splošna varnostna navodila … / Pred začetkom obratovanja / Začetek uporabe

Začetek uporabe / Vzdrževanje in čiščenje / Servis

Page is loading ...

Parkside PAHS 12 A1 Operation and Safety Notes

Brand: Parkside

Model: PAHS 12 A1

Category: Power sanders

Type: Operation and Safety Notes

This manual is also suitable for

88933

Download PDF

report

in other languages

Deutsch: Parkside PAHS 12 A1
slovenčina: Parkside PAHS 12 A1

Parkside PAHS 12 A1 Operation and Safety Notes

This manual is also suitable for

Parkside PAHS 12 A1 Operation and Safety Notes

in other languages

Related papers

Other documents