myPower
™
for iPhone
RECHARGEABLE MOBILE POWER
MP1200/MP1250 User Guide
USER GUIDE
Contents
Overview .............................................................2
Getting Started ....................................................2
Unpacking myPower for iPhone ......................2
Getting to Know myPower for iPhone .............3
Using myPower for iPhone ................................4
Inserting iPhone into the Case .........................4
Viewing the Battery Capacity ...........................5
Charging myPower for iPhone ........................5
Syncing iPhone ................................................6
Storing myPower for iPhone ...........................6
Troubleshooting ..................................................7
Limited Warranty ................................................7
myPower
™
for iPhone
RECHARGEABLE MOBILE POWER
Overview
myPower
™
for iPhone is a lithium polymer
battery wrapped in an elegant leather sleeve.
This battery doubles the run time of the iPhone
battery by powering the connected iPhone
on the go. When plugged into a USB power
adapter or computer USB port, myPower for
iPhone will charge its internal battery, and
that of a connected iPhone. A battery level
indicator shows the amount of remaining
battery power.
As a bonus, myPower for iPhone doubles as a
dock for iPhone, enabling the device to sync
with a connected computer while docked and
charging.
Getting Started
Unpacking myPower for iPhone
Your myPower for iPhone package includes
the following:
User guide (not shown)
myGuard
™
screen protector
(not shown)
myPower
for iPhone
2 MP1200/MP1250
USB cable
Getting to Know myPower for iPhone
Batttery
level
indicator
Mini USB port to
sync and charge
USER GUIDE 3
Rechargeable
lithium polymer
battery
Using myPower for iPhone
You can use myPower for iPhone to power
your iPhone, or to charge your iPhone while
connected to external power. When powering
iPhone, myPower for iPhone will bypass the
iPhone battery to power a connected iPhone,
thus extending the overall life of the iPhone
battery. The battery will not charge iPhone
unless connected to an external power source.
myPower for iPhone is charged in two ways: by
connecting to a USB power adapter, or to a USB
port on a computer. The included USB cable is
used to charge the device. If you are using an
iPhone-compliant USB power adapter, you also
may charge your iPhone at the same time by
inserting the iPhone in the case while connected
to an external power source.
As a bonus feature, myPower for iPhone
doubles as a dock to sync iPhone to your
computer when connected via the USB cable.
In this case, myPower for iPhone will both sync
and charge iPhone.
Inserting iPhone into the Case
Placing iPhone in the Case
1. Slide iPhone into the case, ensuring that the
iPhone is fully docked onto the 30-pin
connector in the bottom of the case.
4 MP1200/MP1250
2. Snap the tab in place to secure iPhone.
3. Use iPhone as you would normally. The
iPhone battery will not be used while iPhone
is docked in the case.
Removing iPhone from the Case
1. Unsnap the tab.
2. Gently pull iPhone from the case.
Viewing the Battery Capacity
When iPhone is docked into the case, the
Battery Level Indicator on the bottom left side of
myPower for iPhone will indicate the remaining
battery capacity as follows:
Green (65%-100%)
Orange (30%-65%)
Red (1%-30%)
Charging myPower for iPhone
An empty myPower for iPhone will charge in
about 3 hours using an iPhone compliant power
adapter. Both empty batteries can be charged in
about 6 hours.
1. Connect the mini USB connector to the mini
USB port on myPower for iPhone.
USER GUIDE 5
2. Connect the USB connector to a USB power
adapter or to a USB port on a computer.
The battery capacity indicator will turn red
to indicate the myPower for iPhone battery
is being charged. If connected, the iPhone
battery charging status indicator will indicate
charging.
3. Unplug the USB cable when the battery
capacity indicator changes from red to green
as the battery is fully charged.
Note: If you are charging iPhone at the same
time, you must use an iPhone-compliant USB
adapter.
Syncing iPhone
The intelligent design of myPower for iPhone
enables you to sync iPhone while charging it via
a USB port on your computer.
1. Connect the mini USB connector to the mini
USB port on myPower for iPhone.
2. Connect the USB connector to a USB port
on a computer. iPhone will sync with your
computer.
Storing myPower for iPhone
Lithium polymer batteries must be used
consistently for maximum performance.
6 MP1200/MP1250
Therefore, if you do not use the battery often,
you should complete a charge cycle (discharge/
recharge the battery) once a month.
While not in use, store myPower for iPhone in a
dry area where the temperature is between -4°
and 113° F (-20 and 45°C). Extreme tempera-
tures can damage the battery, and the battery
life will decrease with higher temperatures or a
moist environment.
Troubleshooting
If myPower for iPhone does not power iPhone,
take these steps:
1. Verify that iPhone is properly docked into the
30-pin connector at the bottom of the case.
2. Check the Battery Level Indicator to verify that
myPower for iPhone is charged.
Limited Warranty
The product enclosed herein is warranted to be
free of operational defects for a period of one
year from the date of purchase. In the event of
a defect in operation during the warranty period
Tekkeon, Inc. will replace the defective product
when the owner returns all product contents.
The limited warranty will be considered void if
the unit is tampered with, subject to misuse,
USER GUIDE 7
negligence or accidental damage, has been
improperly serviced, or if the security seal is
removed. This warranty is limited to replacement
only and shall not cover any other damages.
Any product returned to Tekkeon, Inc. with no
fault found will be returned to the owner at the
owner’s expense.
To obtain warranty coverage, please complete
and submit the enclosed registration card.
Disclaimer of Warranties
Any user of this product does so at the user’s
own risk. To the maximum extent permitted by
applicable law, Tekkeon, Inc. and its suppliers
provide the hardware and any support services
related thereto “as is” and with all faults; and
hereby disclaim all warranties and conditions,
whether express, implied or statutory, includ-
ing, but not limited to implied warranties of
merchantability, fitness for a particular purpose,
non-infringement, lack of negligence or
correspondence to description, except for
those warranties specifically and expressly
provided in the Limited Warranty.
With respect to the use of this product, in no
event shall the company be liable for any loss
of profit or any other commercial damage,
including but not limited to special, incidental,
consequential and other damages.
8 MP1200/MP1250
Customer Support
Customer support for myPower for iPhone is
available at:
Tekkeon, Inc.
c/o myPower for iPhone
3002 Dow Avenue, #134
Tustin, CA 92780
888-787-5888 / 714-832-1266
Tekkeon, Inc. must issue a Return Merchandise
Authorization (RMA) number for all exchanges
or refunds.
www.tekkeon.com
www.tekkeon.com
© 2009 Tekkeon, Inc.
Rev B
All Rights Reserved
myPower™ is a trademark of Tekkeon, Inc.
“Works with iPhone”means that an
electronic accessory has been designed
to connect specifically to iPhone and has
been certified by the developer to meet
Apple performance standards. Apple is not
responsible for the operation of this device
or its compliance with safety and regulatory
standards. iPhone is a trademark of Apple
Inc. Specifications are subject to change
without notice.
Cut loose. Stay loose.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Tekkeon myPower MP1200 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Tekkeon myPower MP1250 User manual
-
Tekkeon myPower MP1280 User manual
-
-
-
-
-
-
-
-
Other documents
-
iLuv mypower50L Quick start guide
-
-
iLuv myPower104 User manual
-
-
-
-
-
-
-